ALECTO DBX-99 Owner’s Manual (DRAFT) 1.
TABLE OF CONTENTS Temperature Setting the Temperature Range Safety Information Getting Started Unpacking Setting the Temperature Alert Sound Alert Vibrate Alert Baby Unit Parent Unit Basic Steps to Install Wall mounting the Baby Unit LCD Display Power On/Off Lullaby Playing the Lullaby Stop lullaby Temporarily Stopping the Lullaby Play Start countdown Timer Start, Stop and Reset the count up timer Monitoring Sensitivity Adjusting Volume Talk Back Paging Torch Nightlight Out of Range Low Battery Ch
Safety Information Baby Unit • • • • Baby Unit Front • • • • • • Avoid exposure of the units to moisture or liquid. Clean the units with a damp cloth. Do not expose the units to extreme heat or direct sunlight. To prevent electric shock, do not open the cabinets of the baby unit, parent unit and charger. Avoid metallic contact (e.g. metal clips, keys) between the battery contacts and charging conductors. Read the marking on the mains adapter for the mains supply required for this baby monitor.
Parent Unit Basic Steps to Install 1. Connect the output plug of the mains adapter to the DC socket at the back of the baby unit and the mains adapter to the wall mains supply. 2. Plug the charger adaptor for the Parent Unit into the mains power socket. 3. Remove the battery door on the Parent Unit by lifting the battery door outward. 4. Insert 2 x AA rechargeable batteries, observing their polarities, into the battery compartment on the Parent Unit. 5. Replace the battery door on the Parent Unit. 6.
Wall mounting the Baby Unit LCD Display Use the following wall mount template to locate and install the mounting pins/screws if you prefer to wall mount your base unit. The dimensions are shown in millimeters (mm). Icon Function • Speaker is muted Sound alert is on and menu is not being navigated. Indicates current battery level • Animated when charging. • When the battery indicator displays 3 blocks, the battery is fully charged.
Power On/Off Sensitivity Baby Unit You can adjust the sensitivity on Parent Unit to monitor the sound from Baby Unit. For example, if your baby is a particularly quiet sleeper, you can increase the sensitivity levels so that you are sure to hear if baby disturbs or becomes uncomfortable. • . The Green Link light comes on to show To switch on, press that the units are within range of each other. • To switch Off, press light goes off until the display goes blank and the link • • Parent Unit • .
Paging Temperature If the Parent Unit is misplaced, you can use the page button on the Baby Unit to locate the Parent Unit. on the Baby Unit. The Parent Unit will automatically • Press reset to mid volume and the paging alert will sound. • PAGING is displayed on the LCDs of both units. • To stop the Page alert, press any button on the Parent Unit, or press again on the Baby Unit. You can monitor the temperature in the baby’s room. The room temperature is constantly displayed in Celsius on both Units.
• • Press Press to confirm. to return the display to standby. Sound Alert Sound alerts are played only on the Parent Unit. You can turn on/off the sound alerts through the menu. • Press scroll to Sound alert. Press • If the sound alert is currently off, Alert On? is displayed. • If the sound alert is currently on, Alert Off? is displayed. to confirm. • Press • Press to return to the standby display. Vibrate Alert Vibrate alert is only available on the Parent Unit.
• If lullaby play is not resumed within 60 seconds, lullaby will stop automatically. Record a lullaby Record your own Lullaby or story words up to <64> seconds long. 1. Press and hold RECORD key on the Baby Unit. Begin recording after the beep. The display shows RECORDING, 2. To end recording, release RECORD. The unit beeps twice. To play your recorded lullaby, follow the steps for Play Lullaby on page 8 and select Own. • • • • • • Press scroll to Timer. Press . Display shows Countdown. Press .
• • When it is stop and displays a counted time, press 00:00:00; again to restart it. Press to reset it to LED will flash. When the units are linked, the green Link LED will be steadily lit. Cancel count up timer. Note: Link break alert cannot be manually set on or off, but it can be suppressed for 4 minutes by pressing any button. There is only visual alert shown on the Baby Unit. • • • • Low Battery scroll to Timer. Press . Press Scroll to Count up. Press . . Timer Off? is displayed.
• • Press again to switch the unit back on. until you hear a While the unit is switching on, press and hold beep. The unit will restore all the original factory settings. Note: If is not pressed within 4 seconds, the unit returns to idle mode. If you want to restore the factory default settings on the baby monitor, you will need to restore factory default setting on the Baby Unit or on the Parent Unit individually.
Packaging information: (Customer’s name) has marked the packaging with standard symbols designed to promote the recycling and appropriate disposal of your eventual waste. The labeled packaging material is recyclable. This product complies with the essential requirements for Radio and Telecommunications Terminal Equipment.
