REV 13E www.WholesaleGateOpener.
Table of Contents General Safety … … … … … … … … … … … … … … ..… … … … … … … … … … … … … … ......… … … … … … … .. 2 Preparation for Installation … … … … … … … … … … … … … … … … … ..… … … … … … … … … … … … … ......… … .. 3 Parts List … … … … … … … … … … … … … … … ..… .… … … … … … … … … … … … … ......… … … … … … … … … … . 4 Optional Accessories Part List … … … … … … … … … … … … … … … ..… .… … … … … … … … … … … … … ......… 5 Technical Specifications & Feature … … … … … … … … .… … … … … … … … ..
Thank you for purchasing our sliding gate opener. We are sure that the products will be greatly satisfying as soon as you start to use it. The product is supplied with a user’ s manual which encloses installation and safety precautions. These should be read carefully before installation and operation as they provide important information about safety, installation, operation and maintenance. This product complies with the recognized technical standards and safety regulations.
Preparation for Installation Before proceeding to your opener installation, check if your gate structure is in accordance with the current standards, especially as follows: The gate sliding track is linear and horizontal. The wheels are suitable for use. The gate should be mounted and moved freely. Check that the structure is sufficiently strong and rigid, and that its dimensions and weights conform to those listed in the specifications table of this document. Make sure that the gate is plumb and level.
Parts List 4
Optional Accessories Parts List Technical Specifications & Features Specifications SCG 17 / AC 1500 SCG 20 / AC 2400 Power supply: 120V/60Hz or 230V/50Hz Motor voltage: 120VAC or 230VAC Frequency 433.92MHz Absorbed power: 300W Gate moving speed: 500W 15 cm/second Max gate weight: 600KGS/1500LBS 1000KGS/2400LBS Max torque: 12Nm 24Nm Environmental conditions: From -15°C to +40°C Protection class: IP44 Dimensions: 25.2×22×25 CM Features: ·Midway mode.
·Built in motor running limitation: max. 90 sec ·Reliable electromagnetism limit for easy adjustment ·Can be equipped with a wide range accessories Installation Overview Installation of the Opener Caution: *Be sure that the opener is installed in a level and paralleled position and is properly secured. Improper installation could result in property damage, severe injury, and/or death.
if necessary to protect the system from flooding, heavy snow etc. 2. Prepare one or more conduits for the electrical cables before pour concrete. Remember that cable conduits have to pass through the hole in the base plate. 3. Pour concrete and before it starts to harden, check that it is parallel to the gate leaf and perfectly level. 4.
washers and nuts temporarily. (Nuts will be further adjusted for a proper chain tension later) 3). Connect second chain bolt with another end of chain from chain box, then attach bolt to the L bracket on opposite end of gate using the washers and nuts. 4). Make sure that the chain is line up exactly with the position where the chain on the chain idler wheel. 5). Get the desired chain tension by adjusting two chain bolts of the both end. Cut the unwanted length of chain if necessary. 6).
Installation of Magnets for Limit Switches Before install limit switch, make sure the gate opener is put in manual operation. (the clutch connected with gear shaft is disengaged) and the mains power supply is disconnected. Position the two Magnet Components approximately on the gate and move the gate by hand to fix them in place. Fit magnets bracket Push the gate fully closed by hand.
Connecting Of Power Supply The power supply cord should be at least 3×0.75mm2. Connect the live wire and neutral wire to the “L”(2) and “N”(1) terminal respectively; and connect the earth wire to “PE”. Connecting Of the Control Board 1. Motor The BLACK wire of the motor should be connected into the “3”terminal. The YELLOW wire of the motor should be connected into the “4”terminal.
The RED wire of the motor should be connected into the “5”terminal. 2. Limit Switches The YELLOW wire of the limit switches should be connected into the “8”terminal. The BLACK wire of the limit switches should be connected into the “9”terminal. The RED wire of the limit switches should be connected into the “10”terminal. 3. Alarm Lamp (Optional) One wire of the alarm lamp should be connected into the “6”terminal, another should be connected into the “7”terminal. 4.
DIP Switch #1–#2: Running time of the motor in Midway Mode DIP Switch #1: ON –2 Seconds OFF –0 DIP Switch #2: ON –4 Seconds OFF –0 NOTE: The midway mode function would be disabled if both DIP switches are turned off. Factory default setting is disabled. E.g. Running time of the operator in pedestrian mode is 2 seconds. DIP Switch #3: Auto close function enabled/disabled DIP Switch #3: ON –auto close function enabled OFF –auto close function disabled E.g.
Test the reversing sensitivity For the sake of safety, it is very important to test the reversing sensitivity as soon as the control board set is finished. The reversing sensitivity adjustment is inverse correlation with stall force adjustment in potentiometer A and B. In other word, the stall force level is higher; the reversing sensitivity level is lower. Put an immobile object along the gate path, and then operate the gate to strike it during the open and close cycles.
Troubleshooting Have a multimeter to check voltage and continuity. Use caution when checking high voltage terminals. Symptom The remote control does not emit any single Possible Solution(s) Check the batteries are exhausted, replace them if necessary. 1. Make sure that the power cord is properly plugged into the mains outlet. 2. Check the fuse is blown in the control board; if necessary, identify the The operator doesn’ t reason for the failure and then replace a new one. 3.
www.WholesaleGateOpener.com 7106 S 220th St, Kent WA 98032 USA sales@WholesaleGateOpener.
