Installation Instructions

SENTREE
Safety and Installation
ALF-000008
ISED REGULATORY STATEMENTS (IC: 22365-ALB050)
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
CAN ICES-003(B) / NMB-003(B)
FCC REGULATORY STATEMENTS (FCC ID: 2AKXF-ALB050)
Changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
this equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
POWER REQUIREMENTS
Rated voltage 240 VAC, single phase, 60 Hz
Rated current 40mA
Rated power 9.6W
Maximum power consumption 12W
REPLACEABLE FUSE
Fuse specications
UL Listed or Recognized Supplemental
Circuit Protection
T 5.0 A H 300 VAC
Replace with same type and fuse rating
Example: Bel Fuse Inc, 0ADKC5000-BE
SAFETY & WARNINGS
ACTIVATE YOUR SENTREE
Go to app.alertlabs.com or download the
app for your iPhone to activate the sensor
and get full installation instructions.
WARNING: RISK OF ELECTRIC SHOCK.
CAN CAUSE INJURY OR DEATH:
DISCONNECT ALL REMOTE ELECTRIC
POWER SUPPLIES BEFORE SERVICING.
WARNING: CLASS 2 WIRING TO BE ROUTED AND
SUPPORTED SUCH THAT IT WILL NOT COME INTO
CONTACT WITH LINE VOLTAGE WIRING OR SHARP
EDGES WITHIN THE ASSEMBLY.
WARNING: REFRIGERANT CAN CAUSE FROSTBITE.
AVOID DIRECT CONTACT WITH THE SKIN. TO PROTECT
HANDS IN THE EVENT OF REFRIGERANT LEAKAGE,
WEAR GLOVES WHILE INSTALLING THE SENSOR.
WARNING
RISK OF ELECTRIC SHOCK.
CAN CAUSE INJURY OR DEATH:
DISCONNECT ALL REMOTE
ELECTRIC POWER SUPPLIES
BEFORE SERVICING
WARNING: RF EXPOSURE COMPLIANCE
The antenna(s) used for this transmitter must be
installed to provide a separation distance of at least
2
0 cm from all persons and must not be co-located
or operating in conjunction with any other product
antenna or transmitter.
CAUTION
Installation must be performed by qualied HVAC
technicians that are certied by the local Air
Conditioner and Refrigeration Licensing Agency.
Good refrigeration practices are expected to be used.
This Sentree device is intended to be connected to
condenser units powered by 240 VAC, single phase,
60 Hz power and must connect to unused 1/4 inch
quick connect terminals on the line side of the
condenser’s contactor.
This Sentree device is intended for use on systems
up to 600 psi operating pressure.
This Sentree device is only intended for use on 1–5
ton residential air conditioner units.
There shall be no cutting of wires, rearrangement
of existing components in the installed unit, cutting,
drilling or welding in electrical compartments or in
other areas where such operations may damage
electrical or refrigerant components and wiring.
This product is not to be used with ammable
refrigerants.
The kit assembly is suitable for locations where the
assembly is occasionally in direct contact with water,
as rain or defrost water, which may be permitted to
collect inside the condensing unit.
PKG-000076-002