User Guide English ( 3 – 14 ) Guía del usuario Español ( 15 – 26 ) Guide d’utilisation Français ( 27 – 38 ) Guida per l’uso Italiano ( 39 – 50 ) Benutzerhandbuch Deutsch ( 51 – 62 ) Appendix English ( 63 )
User Guide (English) Introduction Box Contents Debut drum rack, assembled including: Debut sound module (4) 6” / 15.2 cm drum pads (3) Cymbal poles (3) 10” / 25 cm Cymbal pads (2) Floor pedals (hi-hat and kick) Cable snake Sound module power adapter (2) Sticks Drum Stool Headphones Drum key Velcro strap User Guide Safety & Warranty Manual Support For the latest information about this product (system requirements, compatibility information, etc.) and product registration, visit alesis.com.
Assembly 1. Remove the Debut drum rack, cymbals and cymbal poles from each of their boxes. Place the drum rack (as shown, right) on a flat, level surface. 2. Unfold the rack legs and loosen the joints of each rack arm to unfold. If needed, flip the drum module arm vertically and then tighten to set it in place. Once the kit has been fully expanded, retighten the joint clamps so the arms are secure. 3. Insert the cymbal arms to the empty cymbal clamps on the rack arms and tighten to secure.
4. Remove the wing-nuts and washers from each cymbal stand. Attach the cymbal pads to the poles. Reattach the wing-nuts and washers and tighten to secure the cymbal to the pole. 5. Connect the multipin head of the included cable snake to the port on the bottom side of the Debut module. Tighten the two screws to secure the cable snake to the module. 6. Connect the labeled 1/4" cables at the tail end of the cable snake to each respective drum pad, cymbal and foot pedal in the drum kit.
Module Features Top Panel 2 1 3 4 5 6 7 8 9 1. Power Button: Press this button to turn the drum module on. Press and hold it for 2 seconds to turn the drum module off. 2. Display: This screen shows information relevant to the drum module's current function and operation. 3. Volume Knob: Turn this knob to adjust the volume of the Main Outputs and Phones Output. 4. – / +: Press either of these buttons to decrease or increase the value shown in the display. 5.
Rear Panel 3 4 1 6 5 2 1. Power Jack: Use the included power adapter (9 V, 500 mA, center pin-positive) to connect this jack to your power outlet. 2. Cable Snake Input: Connect the head of the included cable snake here. Connect the cables at the tail end of the cable snake to your kit's triggers (drum pads, cymbal pads, and pedals). 3. Main Outputs: Use standard 1/4" mono cables (not included) to connect these outputs to your monitor, amplifier, or PA system.
Selecting a Kit To select one of the module's 10 preset kits, do one of the following: 1 2 3 4 5 VARIATION • Press the Variation button so it is lit red, and then press the 1, 2, 3, 4, or 5 button to select Kit 1, 2, 3, 4, or 5 respectively. • Press the Variation button so it is lit green, and then press the 1, 2, 3, 4, or 5 button to select Kit 6, 7, 8, 9, or 10 respectively. The Kit Number will appear in the Display.
Using the Metronome (Click) You can use the built-in metronome ("click") to help you keep time while practicing with the built-in Drum Coach or with patterns. You can change the metronome's tempo (speed), volume, sound, and time signature. Turning the Metronome On or Off CLICK To turn the metronome on or off, press the Click button. Adjusting the Metronome Tempo To adjust the metronome's tempo (speed): 1. Press the Tempo button. 2.
Changing the Metronome Interval To change the metronome's note division (the note value it measures with each click): 3 1. Press the Click button and 3 button simultaneously. 2. The Display will show the current interval. Use the – / + buttons to select a new interval: 2 (half note), 3 (triplet), 4 (quarter note), 6 (sextuplet), 8 (eighth note), or 16 (sixteenth note). The default is 4. 3. Wait 4 seconds. The drum module will automatically save the new setting.
Gradual Up/Down This exercise evaluates how quickly you can play while still maintaining accurate time. 2 To use Gradual Up/Down: COACH 1. Press the Pattern button and Tempo button at the same time. Then press the 2 button. 2. Set the metronome's time signature and interval (as described in the Using the Metronome (Click) section). 3. Press the Start/Stop button. 4. Do one of the following: PATTERN TEMPO START /STOP 1 • Press the 1 button to select G-1 Mode.
5. Hit the pads in the rhythm you selected (above) and in time with the metronome (the starting tempo is your metronome's current setting). The six LEDs of the 1-5/Variation buttons indicate how accurate or “in time" you are: • When you are right on the beat, the 3 and 4 buttons will light up. 1 • When you are slightly off the beat, the 2 or 5 button will light up. 2 3 4 5 GOOD SLOW VARIATION FAST • When you are off the beat, the 1 or Variation button will light up.
Drum Mute This exercise lets you silence specific parts of various drum patterns so that you can test different drumming techniques as you fill in the gaps while playing along with the pattern. 5 To use Drum Mute: 1. Press the Pattern button and Tempo button at the same time, and then press the 5 button. COACH PATTERN TEMPO START /STOP 2. Press the Start/Stop button. 3. Use the – / + buttons to select the drum pattern you want to play to. 4.
Triggering Sounds on an External MIDI Device VOL MIDI IN MIDI OUT R L R L USB 1. Using a standard USB cable (not included), connect the drum module's USB port to a USB port on your computer. 2. If you are triggering sounds in software, skip to the next step. 3. 4. 5. If you are triggering sounds in an external MIDI device, make sure that device is connected to your computer (either directly via USB or through a USB-MIDI interface). Set the active track of your MIDI software, sequencer, etc.
Guía del usuario (Español) Introducción Contenido de la caja Batería electrónica Debut ensamblada, incluyendo: Módulo de sonido Debut (4) Pads de tambor de 6 pulg. / 15,2 cm (3) Soporte para platillos (3) Pads de platillos de 10 pulg.
Instalación 1. Retire la estructura de la Debut, los platillos y soportes para platillos de cada una de sus cajas. Coloque la estructura (como se muestra a la derecha) sobre una superficie plana y nivelada. 2. Despliegue las patas de la estructura y afloje las articulaciones de cada brazo de la estructura para poder desplegarlos. De ser necesario, incline el módulo de batería para que quede más vertical y luego ajústelo para que quede firme en esa posición.
4. Retire la tuerca mariposa y la arandela de cada soporte de platillo. Inserte los pads de platillo en los soportes. Vuelva a colocar las tuercas mariposa y las arandelas, y apriételas hasta que los platillos queden firmemente sujetos a los soportes. 5. Enchufe el cabezal multiconector del manojo de cables incluido en el conector que se encuentra del lado inferior del módulo del Debut. Apriete los dos tornillos para sujetar el manojo de cables al módulo. 6. Conecte los cables de 1/4 pulg.
Características Panel superior 2 1 3 4 5 6 7 8 9 1. Botón de encendido: Pulse este botón para encender el módulo de batería. Manténgalo pulsado 2 segundos para apagar el módulo de batería. 2. Pantalla: Esta área muestra valores y texto relevantes de las funciones y la operación del módulo de batería. 3. Perilla de volumen: Gire esta perilla para ajustar el volumen de las salidas Main (Principal) y Phones (Auriculares). 4.
Panel trasero 3 4 1 6 5 2 1. Conector hembra de alimentación: Use el adaptador de alimentación incluido (de 9 V, 500 mA, pin central positivo) para conectar este conector hembra al tomacorriente. 2. Conector del multicable: Conecte aquí su multicable incluido y conecte los cables del multicable a los disparadores de su kit (pads de tambor, pads de platillos y pedales). 3. Salidas principales: Use cables mono estándar de 1/4 pulg.
Cómo seleccionar un kit Para seleccionar uno de los 10 kits preprogramados del módulo, realice uno de los siguientes procedimientos: 1 2 3 4 5 VARIATION • Pulse el botón Variation de modo que se ilumine verde y luego pulse el botón 1, 2, 3, 4 o 5 para seleccionar el Kit 1, 2, 3, 4 o 5 respectivamente. • Pulse el botón Variation de modo que se ilumine rojo y luego pulse el botón 1, 2, 3, 4 o 5 para seleccionar el Kit 6, 7, 8, 9 o 10 respectivamente. El número del kit aparece en la Pantalla.
Usar el metrónomo (clic) Puede usar el metrónomo integrado ("clic") para ayudarle a mantener el tiempo cuando practica con el instructor de batería integrado o con patrones. Puede cambiar el tempo (velocidad), el volumen, el sonido y la firma de tiempo del metrónomo. Activar y desactivar el metrónomo CLICK Para activar o desactivar el metrónomo, pulse el botón Click. Ajustar el tempo del metrónomo Para ajustar el tempo (velocidad) del metrónomo: 1. 2. 3. Pulse el botón Tempo.
Cambiar el intervalo del metrónomo Para cambiar la división de notas (el valor de la nota que mide con cada clic) del metrónomo: 3 CLICK 1. Pulse simultáneamente los botones Click y 3. 2. Aparece en la Pantalla el intervalo actual. Use los botones – / + para seleccionar un nuevo intervalo: 2 (blanca), 3 (tresillo), 4 (negra), 6 (seisillo), 8 (corchea), or 16 (semicorchea). El valor predeterminado es 4. 3. Espere 4 segundos. El módulo de batería guarda automáticamente el nuevo ajuste.
Gradual Up/Down (El arriba/abajo gradual) El ejercicio arriba/abajo gradual permite evaluar cuán rápidamente puede tocar mientras mantiene un tiempo preciso. Para usar el arriba/abajo gradual: 2 COACH 1. Pulse simultáneamente los botones Pattern y Tempo y luego pulse el botón 2. 2. Ajuste la firma de tiempo y el intervalo del metrónomo (según se explica en la sección Usar el metrónomo (clic)). 3. Pulse el botón Start/Stop. 4.
5. Golpee los pads al ritmo que seleccionó (arriba) y en sincronismo con el metrónomo (el tempo inicial es el ajuste de su metrónomo de ese momento). Los seis LED de los botones 15/Variation indican cuán preciso ("a tiempo") va usted: • Cuando está bien en el beat, se encienden los botones 3 y 4. 1 2 • Cuando está ligeramente fuera del beat, se encienden los botones 2 y 5. • Cuando está fuera del beat, enciende el botón 1 o Variation.
Drum Mute (El silencio de batería) El ejercicio de silencio de batería le permite silenciar ciertas partes de los diversos patrones de batería para que pueda tocar libremente y crear sus propias partes sobre el resto del patrón de batería. 5 Para usar el silencio de batería: 1. Pulse simultáneamente los botones Pattern y Tempo y luego pulse el botón 5. COACH PATTERN TEMPO START /STOP 2. Pulse el botón Start/Stop. 3. Use los botones – / + para seleccionar el patrón de batería con el que desea tocar.
Disparar sonidos en un dispositivo MIDI externo VOL MIDI IN MIDI OUT R L R L USB 1. Usando un cable USB estándar (no incluido), conecte el puerto USB del módulo de batería a un puerto USB de su computadora. 2. Si está disparando sonidos en software, salte al paso siguiente. Si está disparando sonidos en un dispositivo MIDI externo, asegúrese de que el dispositivo esté conectado a su computadora (ya sea directamente por USB o por medio de una interfaz USB-MIDI). 3.
Guide d’utilisation (Français) Présentation Contenu de la boîte L’ensemble de batterie Debut assemblé comprend : Module de son Debut 4 pads de batterie de 15,2 cm 3 tiges de cymbale 3 pads de batterie de 25 cm 2 Pédales au sol (charleston et grosse caisse) Câble multipaire Adaptateur secteur du module de son 2 pilons Banc Casque d'écoute Clé de batterie Bande de fixation Velcro Guide d’utilisation Consignes de sécurité et informations concernant la garantie Assistance Pour les dernières informations concer
Démarrage 1. Retirez le support de batterie, les cymbales et les tiges de cymbale Debut de leurs emballages. Placez le support de batterie (comme illustré, à droite) sur une surface plane et de niveau. 2. Dépliez les pieds du support et dévissez les bagues de fixation des articulations sur chaque bras afin de pouvoir les déplier. Si nécessaire, placez le bras du module de son à la verticale, puis revissez-le.
4. Retirez les écrous à oreilles et les rondelles de chaque tige de cymbale. Fixez les pads de cymbale aux tiges. Revissez les écrous à oreilles et les rondelles afin de fixer la cymbale à la tige. 5. Reliez la tête multibroches du câble multipaire fourni au port sur le dessous du module Debut. Serrez les deux vis pour fixer le câble multipaire au module. 6.
Caractéristiques Panneau supérieur 2 1 3 4 5 6 7 8 9 1. Interrupteur d'alimentation : Appuyez sur cette touche afin de mettre le module sous tension. Maintenez-la enfoncée pendant 2 secondes afin de mettre le module hors tension. 2. Écran d’affichage : Cet écran affiche les valeurs et le texte pertinent selon les fonctions et le fonctionnement du module. 3. Volume : Tournez ce bouton pour régler le volume de la sortie principale et casque. 4.
Panneau arrière 3 4 1 6 5 2 1. Entrée d’alimentation : Utilisez l’adaptateur secteur inclus (9 V, 500 mA, fiche à centre positif) pour relier cette entrée à une prise secteur. 2. Connecteur de câble multipaire : Branchez le câble multipaire inclus ici, puis ses extrémités aux déclencheurs de votre ensemble de batterie (pads de batterie, pads de cymbales et pédales). 3.
Sélection d’un ensemble de sonorités de batterie (kit) Pour sélectionner un des 10 ensembles de sonorités programmés du module, effectuez l'une des opérations suivantes : • Appuyez sur la touche Variation afin qu’elle s’allume rouge, puis sur la touche 1, 2, 3, 4 ou 5 pour sélectionne l’ensemble 1, 2, 3, 4 ou 5 respectivement.
Utilisation du métronome (clic) Vous pouvez utiliser le métronome intégré (« clic ») pour vous aider à garder le rythme tout en pratiquant avec le professeur de batterie intégré ou avec des enchaînements. Vous pouvez modifier le tempo (vitesse), le volume, le son et la division temporelle du métronome. Activation ou désactivation du métronome CLICK Pour activer ou désactiver le métronome, cliquez sur la touche Click. Réglage du tempo du métronome Pour régler le tempo (vitesse) du métronome : 1.
Modification de l’intervalle du métronome Pour modifier la division du temps du métronome (le nombre de temps par mesure pour chaque clic) : 1. Appuyez simultanément sur les touches Click et 3. 2. L’écran affiche l’intervalle en cours. Utilisez les touches – / + pour sélectionner un nouvel intervalle : 2 (blanche), 3 (triolet), 4 (noire), 6 (sextolet), 8 (croche) ou 16 (double croche). La valeur par défaut est 4. 3. Attendez 4 secondes. Le module enregistrera automatiquement le nouveau réglage.
Gradual Up/Down (accélération et ralentissement progressif) L’option d’accélération et de ralentissement progressif permet d’évaluer la vitesse avec laquelle vous jouer tout en conservant les temps. 2 Pour utiliser Gradual Up/Down : COACH 1. Appuyez simultanément sur les touches Pattern et Tempo, puis sur la touche 2. 2. Réglez les paramètres de la division temporelle et de l’intervalle (comme indiqué dans la section Utilisation du métronome (clic)). 3. Appuyez sur la touche Start/Stop. 4.
5. Frappez les pads au rythme sélectionné (ci-dessus) et en temps avec le métronome (le tempo initial est la valeur actuelle du réglage du métronome). Les six DEL des touches 1-5/Variation indiquent la précision (en temps) avec laquelle vous frappez les pads : • Lorsque vous suivez le rythme, les touches 3 et 4 s’allument. • Lorsque vous êtes légèrement décalé, la touche 2 ou 5 s'allume. 1 • Lorsque vous êtes décalé, la touche 1 ou Variation s'allume.
Drum Mute (Mise en sourdine de certaines parties de l’enchaînement) L’option de mise en sourdine de certaines parties de l’enchaînement vous permet de jouer en toute liberté et de créer vos propres composants que vous pouvez ajouter à l'enchaînement. 5 Pour utiliser Drum Mute : 1. Appuyez simultanément sur les touches Pattern et Tempo, puis sur la touche 5. 2. Appuyez sur la touche Start/Stop. 3. Utilisez les touches – / + pour sélectionner l’enchaînement de batterie que vous désirez jouer. 4.
Déclencher des sons sur un appareil MIDI externe VOL MIDI IN MIDI OUT R L R L USB 1. À l'aide d'un câble USB standard non inclus, reliez le port USB du module de percussion à un port USB sur votre ordinateur. 2. Si vous déclenchez des sons d’un logiciel, passez à l'étape suivante. Si vous déclenchez des sons d’un appareil MIDI externe, assurez-vous que cet appareil est branché à votre ordinateur (que ce soit directement via le port USB ou via une interface USB-MIDI). 3.
Guida per l’uso (Italiano) Introduzione Contenuti della confezione Rack per batteria Debut assemblato con inclusi: Modulo audio Debut (4) pad batteria da 6” / 15,2 cm (3) montante dei piatti (3) pad piatti da 10” / 25 cm (2) pedali da terra (hi-hat e grancassa) Fascio di cavi Adattatore di alimentazione modulo audio (2) bacchette Sgabello batteria Cuffie Chiave per batteria Fascetta in velcro Guida per l’uso Istruzioni di sicurezza e garanzia Assistenza Per conoscere le ultime informazioni in merito a ques
Configurazione 1. Rimuovere il rack per batteria Debut, piatti e montanti dei piatti da ciascuna delle loro confezioni. Collocare il rack per batteria (come illustrato a destra), su una superficie piana e uniforme. 2. Aprire le gambe del rack e allentare i giunti di ciascun braccio rack per aprirlo. Se necessario, collocare il braccio del modulo batteria verticalmente, quindi stringerlo per fissarlo in posizione.
4. Rimuovere i dadi ad alette e le rondelle da ciascun supporto per piatti. Fissare i pad piatti alle aste. Fissare nuovamente i dadi ad alette e le rondelle e stringerli per fissare il piatto all’asta. 5. Collegare la testa a più poli del fascio di cavi in dotazione alla porta sul lato inferiore del modulo Debut. Stringere le due viti per fissare il fascio di cavi al modulo. 6.
Caratteristiche Pannello superiore 2 1 3 4 5 6 7 8 9 1. Tasto di alimentazione: premere questo pulsante per accendere il modulo batteria. Tenerlo premuto per 2 secondi per spegnere il modulo batteria. 2. Display: quest'area mostra valori e scritte specifiche relativi alle funzioni e al funzionamento del modulo batteria. 3. Manopola volume: girare questa manopola per regolare il volume delle uscite principali e dell’uscita cuffie. 4.
Pannello posteriore 3 4 1 6 5 2 1. Jack di alimentazione: servirsi di un adattatore di alimentazione in dotazione (9 V, 500 mA, polo centrale positivo) per collegare questo jack alla presa di corrente. 2. Connettore per il fascio di cavi: collegare il fascio di cavi in dotazione a questo livello e collegare i cavi del fascio ai trigger del kit (pad batteria, pad piatti e pedali). 3.
Selezionare un Kit Per selezionare uno dei 10 Kit preset del modulo, procedere in uno dei seguenti modi: 1 2 3 4 5 VARIATION • Premere il tasto Variation in modo da farlo accendere rosso, quindi premil tasto 1, 2, 3, 4 o 5 per selezionare il Kit 1, 2, 3, 4 o 5 rispettivamente. • Premere il tasto Variation in modo da farlo accendere verde, quindi premere il tasto 1, 2, 3, 4 o 5 per selezionare il Kit 6, 7, 8, 9 o 10 rispettivamente. Il numero di Kit compare a Display.
Uso del metronomo (Click) Per aiutarsi a tenere il tempo durante gli esercizi con il Drum Coach incorporato o con i pattern, è possibile utilizzare il metronomo incorporato ("click"). È possibile cambiare il tempo (velocità), il volume, il suono e la divisione metrica del tempo tenuta dal metronomo. Accensione e spegnimento del metronomo CLICK Per accendere o spegnere il metronomo premere il tasto Click. Regolazione del tempo del metronomo Per regolare il tempo (velocità) del metronomo: 1.
Modifica dell'intervallo del metronomo Per modificare la divisione in note del metronomo (il valore della nota che misura con ciascun clic): 3 1. Premere contemporaneamente il tasto Click e il tasto 3. 2. Il Display mostrerà l'intervallo corrente. Servirsi dei tasti – / + per selezionare un nuovo intervallo: 2 (minima), 3 (terzina), 4 (semiminima), 6 (sestina), 8 (croma) o 16 (semicroma). L'intervallo predefinito è 4. 3. Attendere per 4 secondi.
Utilizzo della funzione Gradual Up/Down La funzione Gradual Up/Down valuta quanto velocemente si è in grado di suonare, pur mantenendo un tempo preciso. Per utilizzare la funzione Gradual Up/Down: 1. Premere il tasto Pattern e il tasto Tempo contemporaneamente, quindi premere il tasto 2. 2. Impostare divisione metrica del tempo e intervallo del metronomo (si veda Utilizzo del metronomo (Click)). 3. Premere il tasto Start/Stop. 4.
5. Battere i pad al ritmo selezionato (vedi sopra) e a tempo con il metronomo (il tempo iniziale è l'impostazione corrente del metronomo). I sei LED a livello dei tasti 1-5/Variation indicano il livello di precisione raggiunto (quanto si è "a tempo"). • Quando si è perfettamente a tempo, si accendono i tasti 3 e 4. 1 2 • Quando si è leggermente fuori tempo, si accendono i tasti 2 o 5. 3 4 5 VARIATION GOOD SLOW FAST • Quando si è fuori tempo, si accendono i tasti 1 o Variation.
Utilizzo della funzione Drum Mute La funzione Drum Mute consente di silenziare determinate parti di vari pattern di batteria, consentendo di suonare liberamente e di creare parti personalizzate nel resto del pattern di batteria. Per utilizzare il Drum Mute: 1. Premere il tasto Pattern e il tasto Tempo contemporaneamente, quindi premere il tasto 5. 5 COACH PATTERN TEMPO START /STOP 2. Premere il tasto Start/Stop. 3.
Attivazione di suoni su un dispositivo MIDI esterno VOL MIDI IN MIDI OUT R L R L USB 1. Servendosi di un cavo USB standard (non in dotazione), collegare la porta USB del modulo batteria ad una porta USB del computer. 2. Se si attivano suoni in un software, saltare al passaggio successivo. Se si attivano suoni in un dispositivo MIDI esterno, assicurarsi che il dispositivo sia collegato al computer (o direttamente tramite USB o tramite un'interfaccia USB-MIDI). 3.
Benutzerhandbuch (Deutsch) Einführung Lieferumfang Debut Drum Rack, enthält zusammengebaut: Debut Sound-Modul (4) 6” / 15,2 cm Drum-Pads (3) Beckenständer (3) 10” / 25 cm Becken-Pads (2) Bodenpedale (Hi-Hat und Kick) Kabelschlange Soundmodul-Netzteil (2) Sticks Trommelhocker Kopfhörer Stimmschlüssel Klettverschluss Benutzerhandbuch Sicherheitshinweise und Garantieinformationen Kundendienst Für aktuelle Informationen zu diesem Produkt (Systemanforderungen, Kompatibilität etc.
Setup 1. Nehmen Sie das Debut Drum Rack, die Becken und Beckenständer aus den Schachteln. Stellen Sie das Drum-Rack (wie rechts gezeigt) auf eine ebene Fläche. 2. Klappen Sie die Rackbeine auseinander und lösen Sie die Gelenke jedes Rackarms, um sie zu aufzuklappen. Klappen Sie den Drummodularm bei Bedarf vertikal um und ziehen Sie ihn dann fest, um ihn in Position zu bringen. Ziehen Sie die Gelenkklemmen nach dem vollständigen Ausbau des Kits wieder fest, damit die Arme sicher sind. 3.
4. Entfernen Sie die Flügelmuttern und Unterlegscheiben von jedem Beckenständer. Befestigen Sie die Beckenpads an den Ständern. Bringen Sie die Flügelmuttern und Unterlegscheiben wieder an und ziehen Sie sie fest, um das Becken am Ständer zu befestigen. 5. Verbinden Sie den Multipin-Kopf der mitgelieferten Kabelschlange mit dem Anschluss an der Unterseite des Debut-Moduls. Ziehen Sie die beiden Schrauben an, um die Kabelschlange am Modul zu befestigen. 6.
Funktionen Oberseite 2 1 3 4 5 6 7 8 9 1. Netzschalter: Drücken Sie diese Taste, um das Drum-Modul einzuschalten. Halten Sie diese Taste 2 Sekunden lang gedrückt, um das Drum-Modul auszuschalten. 2. Display: Dieser Bereich zeigt Werte und Text zu Funktionen und Betrieb Ihres Drum-Moduls an. 3. Lautstärkeregler: Drehen Sie diesen Regler, um die Lautstärke der Hauptausgänge und des Kopfhörerausgangs einzustellen. 4.
Rückseite 3 4 1 6 5 2 1. Netzeingangsbuchse: Verwenden Sie ein Netzteil (im Lieferumfang enthalten, 9 V, 500 mA, mittlerer Pin mit positiver Polarität), um diese Buchse mit einer Steckdose zu verbinden. 2. Kabelschlangenanschluss: Hier können Sie Ihre Kabelschlange (im Lieferumfang enthalten) anschließen. Verbinden Sie die Kabel mit den Triggers (Drum-Pads, Becken-Pads und Pedale) Ihres Kits. 3.
Auswählen eines Kits Um eines der Preset-Kits dieses Moduls auszuwählen, gehen Sie wie folgt vor: • Drücken Sie die Taste Variation, so dass die Anzeige aufleuchtet grün. Drücken Sie anschließend die Tasten 1, 2, 3, 4 oder 5, um jeweils Kit 1, 2, 3, 4 oder 5 auszuwählen. 1 2 3 4 5 VARIATION • Drücken Sie die Taste Variation, so dass die Anzeige aufleuchtet rot. Drücken Sie anschließend die Tasten 1, 2, 3, 4 oder 5, um jeweils Kit 6, 7, 8, 9 oder 10 auszuwählen.
Einstellen des Metronoms (Klick) Sie können das integrierte Metronom ("den Klick") verwenden, um Ihnen dabei zu helfen, im Takt zu bleiben, wenn Sie mit dem integrierten Drum-Coach oder den Vorlagen üben. Sie können Tempo (Geschwindigkeit), Lautstärke, Klang und Taktart des Metronoms ändern. Ein- und Ausschalten des Metronoms CLICK Um das Metronom ein- oder auszuschalten, drücken Sie die Klick-Taste. Einstellen des Metronom-Tempos So stellen Sie das Tempo (Geschwindigkeit) des Metronoms ein: 1.
Ändern des Metronomintervalls So ändern Sie die Notenaufteilung des Metronoms (den Notenwert, der jedem Klick zugewiesen wird): 1. Drücken Sie gleichzeitig auf die Klick-Taste und die Taste 3. 2. Das Display zeigt das aktuelle Intervall. Verwenden Sie die Tasten - / +, um ein neues Intervall zu wählen: 2 (halbe Note), 3 (Triole), 4 (Viertelnote), 6 (Sextole), 8 (Achtelnote) oder 16 (Sechzehntelnote) (der Standardwert ist 4). 3. Warten Sie 4 Sekunden.
Gradueller Tempowechsel Beim graduellen Tempowechsel wird bewertet, wie schnell Sie spielen können ohne aus dem Takt zu kommen. So starten Sie die Übung "Gradueller Tempowechsel": 2 COACH 1. Halten Sie die Vorlagetaste und die Tempo-Taste gleichzeitig gedrückt und drücken anschließend die Taste 2. 2. Legen Sie die Taktart des Metronoms und das Intervall fest (im Abschnitt Einstellen des Metronoms (Klick) beschrieben). 3. Drücken Sie die Start-/Stopp-Taste. 4.
4. Drücken Sie die Start-/Stopp-Taste, um zu beginnen. 5. Schlagen Sie im (oben) gewählten Rhythmus und in Übereinstimmung mit dem Metronom auf die Pads (das Ausgangstempo entspricht der aktuellen Metronomeinstellung). Die sechs LEDs der 15/Variationstasten zeigen an, wie "taktgenau" Sie spielen. • Wenn Sie genau im Takt spielen, leuchten die Tasten 3 und 4 auf. 1 • Wenn Sie nicht ganz genau im Takt sind, leuchten die Tasten 2 und 5 auf.
Stummschalten Bei dieser Übung können Sie bestimmte Teile der verschiedenen Schlagzeugrhythmen stumm schalten, so dass Sie frei spielen und ihre eigenen Rhythmen zu den restlichen Rhythmuselementen spielen können. So starten Sie die Übung "Stummschalten": 5 COACH 1. Halten Sie die Vorlagetaste und die Tempo-Taste gleichzeitig gedrückt und drücken anschließend die Taste 5. PATTERN TEMPO 2. Drücken Sie die Start-/Stopp-Taste. 3. Verwenden Sie die Tasten Schlagzeugrhythmus auszuwählen. 4.
Triggern von Sounds auf externen MIDI-Geräten VOL 1. 2. MIDI IN MIDI OUT R L R L USB Verbinden Sie den USB-Anschluss des Drum-Moduls über ein Standard-USB-Kabel (separat erhältlich) mit einem USB-Anschluss Ihres Computers. Wenn Sie Sounds in einer Software triggern, überspringen Sie den nächsten Schritt. Wenn Sie Sounds in einem externen MIDI-Gerät triggern, stellen Sie sicher, dass das Gerät an Ihren Computer angeschlossen ist (entweder direkt über USB oder über eine USB-MIDI-Schnittstelle). 3.
Appendix (English) Technical Specifications Kits 10 preset kits; 5 General MIDI (GM) kits Sequencer 30 Patterns; 12 "Follow Me" patterns Resolution 192 ticks per quarter note Maximum Polyphony 64 Display 3-digit LED Tempo 30 – 280 BPM Connectors 25-pin trigger input jack (for cable snake) 1/8" TRS headphone output 1/4" TS main outputs (right and left/mono) 1/8" TRS auxiliary input USB port (MIDI) Power jack Power 9 V, 500 mA, center pin-positive Dimensions 5.8" x 7.2" x 4.
alesis.com Manual Version 1.