Alfa Laval CM Condition Monitor 2067-0000 Lit. Code Manual No.
Published by Alfa Laval Kolding A/S Albuen 31 DK-6000 Kolding, Denmark +45 79 32 22 00 The original instructions are in English © Alfa Laval Corporate AB 2021-06 This document and its contents are subject to copyrights and other intellectual property rights owned by Alfa Laval Corporate AB. No part of this document may be copied, re-produced or transmitted in any form or by any means, or for any purpose, without Alfa Laval Corporate AB’s prior express written permission.
Contents 1 EC Declaration of Conformity.......................................................................... 5 2 About Condition Monitor...................................................................................... 7 3 2.1 Purpose of this manual..............................................................................................8 2.2 Use of symbols..........................................................................................................9 Installation...........
EN 1 EC Declaration of Conformity The Designation Company Alfa Laval Kolding A/S Compagny Name Albuen 31, DK-6000 Kolding, Denmark Address +45 79 32 22 00 Phone No hereby declare that Alfa Laval CM Condition Monitor Designation Type Conformities - ESTI EN 301 480 - 1 Electromagnetic Compatibility (EMC) - CISPR32 EN 55032 - Electromagnetic compatibility of multimedia equipment. - ESTI EN 300 328 V2.1.
EN 1 EC Declaration of Conformity ISED Statements: This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
EN 2 About Condition Monitor The Condition Monitor (CM) is a compact, easy to use, vibration monitoring system which allows the user to monitor the condition of rotating equipment. The CM is battery powered, and communication is performed wirelessly by means of Bluetooth, thus no need for cabling. During operation, the CM measures equipment vibration. The measurements are compared against a baseline set during an initial “Teach” calibration period, which reflects a normal condition.
EN 2 About Condition Monitor 2.1 Purpose of this manual NOTE Save this manual for future reference and keep it readily available. For detailed use of product guidance, consult the Alfa Laval Condition Monitor application. Requesting other information for instructions, situations, or events that are not considered in this manual or in the sales documents, please contact your local Alfa Laval representative.
About Condition Monitor 2 EN 2.2 Use of symbols This section describes the symbols used throughout this manual. Note NOTE Information considered important to the reader, but not related to hazards. Attention ATTENTION Informs the reader about a potential hazard, if not avoided will result in serious injury. Hot surface HOT SURFACE Informs the reader about potential hot surfaces.
EN 2 About Condition Monitor 10 200002050-2-EN-GB
EN 3 Installation NOTE When mounting the CM, it is important to achieve a solid mechanical connection between the equipment and the CM in addition to any adapter if fitted, ideally mounted to a flat surface. The CM can be mounted on surfaces up to 80° C (176° F). 3.1 General Guidelines The general guidelines for custom fitting of the CM to rotating equipment, we recommend the following.
EN 3 Installation 3.3 Setup 1 Install and open the Alfa Laval Condition Monitor application. Scan the QR code see “Section 3.4 Software”. 2067-0001 2 Wake up the CM by shaking it, until the LED flashes blue or hold a magnet to the QR-code until the LED flashes blue, then remove the magnet.
Installation 3 EN 3 Mount the CM on the rotating equipment. 2067-0004 4 Connect your handheld device with the CM, and follow the “First Time Setup” instructions in the Alfa Laval Condition Monitor application. 2067-0005 3.4 Software To install the Alfa Laval Condition Monitor application, use a handheld device that operates with Android or iOS - Direct download via QR-code. 2067-0007 * Application download in China with Android: Go to Condition Monitor product page, at www.alfalaval.
EN 3 Installation 14 200002050-2-EN-GB
EN 4 Safety NOTE Attention Failure to observe the instructions contained in this manual could result in personal injury and property damage, and may void the warranty. Read this manual carefully before installing and using the product. 4.1 Product ATTENTION Attention Never heat the Condition Monitor to temperatures in excess of 90°C (194°F). Heating above these temperatures could result in serious injury. Never dispose of the Condition Monitor in a fire, this could result in serious injury.
EN 4 Safety 16 200002050-2-EN-GB
EN 5 Troubleshooting Issue Cause Connection The CM does not appear in the “My The CM is in sleep mode. Devices” list. Shake the CM and wait for the blue LED to blink or wake the CM by use of a magnet, see “Section 5.1 Magnet functionality” The CM does not wake up when performing the wake instructions. The CM software may be suspended. Perform a software reboot by use of the magnet, if the reboot does not correct the issue, perform a factory reset by use of a magnet, see “Section 5.
EN 5 Troubleshooting 18 200002050-2-EN-GB
Troubleshooting 5 EN 5.2 Tips and tricks Wink function: Locating a CM among other CM´s To easily identify a CM from others, use the Wink functionality. In the My Devices list tap and hold a CM card, until the Wink dialog pops up. Selecting Wink, will instruct the CM to flash purple with 1 second between flashes for a total of 1 minutes, giving the user time to visually locate the CM.
EN 5 Troubleshooting 20 200002050-2-EN-GB
EN 6 Addendum Alfa Laval Specific Equipment Installation Guidelines.
