Advanced Image Processing Solutions Dual SD/HD Frame Synchronizer Installation and Operation Manual C3032-8001-201 Copyright Algolith 2008, all rights reserved
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation Table of Contents Safety ...........................................3 Introduction ...................................4 About this manual .................................. 4 Overview ............................................... 4 Main Features ........................................ 4 Main Features ........................................ 5 Main Features ....................................... 5 The Algogear Series .................
Guide to installation and operation Safety FRS-1002-MD / FRS-1002-MD-LG-PA Electromagnetic Compatibility Before using this product, carefully review all the safety precautions in this user guide, and all the important regulatory and safety notices in the openGear DFR8310-C Multi-Definition Digital Products Frame User Manual.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA Introduction About this manual This user guide covers both the FRS-1002-MD and FRS-1002-MD-LG-PA cards. The FRS-1002 cards share many common features and the general content of this user guide applies to both products. Content and features specific to either product will be outlined by these graphic headers, so they can be easily associated with the proper product. Enjoy your reading.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation MD Main Features The FRS-1002-MD is a dual channel frame synchronizer. It processes 2 independent channels simultaneously in SD or HD. In addition, it processes 16 channels (4 groups) of embedded audio. Video and audio delay can be controlled independently. The graphic below represents a functional block diagram of the FRS-1002-MD. Output 1A Input 1 2 x 16 ch. Audio Mux Frame Sync Input 2 Output 1B Output 2A Output 2B 2 X 16 ch.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA The Algogear Series Designed for openGear, Algogear is a flexible, future-proof, modular solution that can maximize bandwidth, clean, synchronize and scale media. Algogear delivers unparalleled value and flexibility to broadcasters leveraging the Algogear solution, giving the ground-breaking ability to reprogram the cards with any of the available Algogear solutions at any time, at no cost.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation Installation and setup Static Discharge Whenever handling the FRS-1002 and other related equipment, please observe all static discharge precautions as described in the following note: Static discharge can cause serious damage to sensitive semiconductor devices. Avoid handling circuit boards in high static environments such as carpeted areas, and when wearing synthetic fiber clothing.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA Installation and setup The FRS-1002 card is installed in the openGear frame. openGear frame The FRS-1002 card requires a BNC rear output module. Depending on the frame model you purchased, your frame may be equipped with a fixed 100 BNC rear panel. openGear frame with a fixed 100 BNC rear panel Your frame model may have a modular rear panel, to accommodate different types of cards.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation Power Consumption The power rating of the openGear frame allows 125 watts to be redistributed over 10 slots. A single slot may exceed 12 watts but the overall power consumption shall not be above 125 watts. The FRS-1002-MD and FRS-1002-MD-LG-PA dissipate 14 watts. An openGear frame, when populated with Algogear cards only (VNR-1000-SD, VNR-1000-HD, XVC-1001-UC, XVC-1001-UC-BFSA, FRS-1002-MD and FRS-1002-MD-LG-PA...
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA 6 status LEDs are located near the FRS-1002 card’s front edge. Consult the graphic and color code below to identify the LEDs and their meanings Card Status - LED color code Green Yellow Red Normal Minor Problem Critical error Rear Input / Output Module Labels Algolith’s FRS-1002 card comes with the rear module labels of every available Algogear product at the time of purchase.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation Output Channels The FRS-1002 has 2 HD/SD-SDI inputs and 4 HD/SD-SDI outputs. Each channel in the Dashboard user interface corresponds to the matching input number. The label on the card’s BNC rear output module, at the back of the openGear frame, identifies the inputs and outputs.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA Operation Once installed in the openGear frame, the FRS-1002 card is controlled through the Dashboard software (version 2.2 or higher). For information on how to install the software and to manage openGear frames in Dashboard, please consult the Dashboard Software User Manual, provided on the installation CD you have received with this purchase, or visit our website at: http://www.algolith.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation The Basic Tree View Window All openGear frames and compatible cards in your system are displayed in the device list window. Select the card you wish to control in the Basic Tree View tab. For more information on the device list please consult the Dashboard Software User Manual, provided on the installation CD.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA The Card Status Window The Card Status window displays the input video format for each channel, the input audio format for each channel, and the reference video input. Control The user can control the FRS-1002 card’s various parameters in the Card Setup, Video Setup, Audio Setup and Alarm Setup windows. The following section describes how to adjust the parameters.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation Adjusting Parameters The FRS-1002 card provides an extra level of control and security with an administrator password-protected level, in which the parameters of the card can be modified and controlled. The non password-protected level or «read only» mode, where no password is entered, allows users to view the various settings, but does not permit changes to be made.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA The Card Setup Window The Card Setup window allows the configuration of parameters affecting the overall functionality of the card. Recall & apply settings Save settings Save Settings Destination The Save Settings Destination function allows the user to save up to 4 configurations of the FRS-1002 card’s parameters per channel.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation Selecting the Reference The FRS-1002 card provides four methods for referencing the incoming video signal. At the bottom of the Card Setup window, the reference selection can be chosen from a drop down menu. The reference selection is automatically saved and will be restored after power-up. The FRS-1002 accepts tri-level, bi-level and black burst reference signals. The video inputs can be synchronized with the house sync signal.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA External Card (BNC 10): Uses the reference signal from the FRS-1002 card’s rear module REF input.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation Video Setup Window The Video Setup window allows the configuration of video parameters affecting the individual channels of the card. Video Default Mode The video Default mode function is used if no valid video is detected at the input. Also, a reference mismatch may occur if there is a difference between the input video format’s frame rate and the reference format’s frame rate.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA Video Delay (line) The Video Delay (line) function allows users to adjust the delay in increments of one line. Maximum line delay values vary depending on the input format as follows: Format Line Delay Range 408i59.94 0 to 524 576i50 0 to 624 720p50 0 to 749 720p59.94 0 to 749 720p60 0 to 749 1080i50 0 to 1124 1080i59.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation LG-PA The Video Setup window for the FRS-1002-MD-LG-PA allows for configuration of the same video parameters as the FRS-1002MD, however, additional settings are available for the card’s Legalizer and Proc Amp. Proc Amp Legalizer Proc Amp The proc amp allows for adjustments to the Brightness, Contrast, Saturation and Hue levels of the video image. These parameters can be set as follows: Parameters Range Brightness -10% to 10%, in 0.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA Audio Setup Window The FRS-1002 card supports 16 audio channels in 4 groups of PCM-20 bits and PCM-24 bits encoded audio at 48KHz. The Audio Setup window allows the configuration of audio parameters (16 channels, 4 groups) affecting the individual channels of the card.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation Audio Delay Custom (ms) Sets the audio delay in 1 millisecond increments for a maximum value of 10 seconds. Audio Delay Custom (samples) Sets the audio delay in 1 sample increments for a maximum value of 47 audio samples.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA Channel A, Channel B Channel A represents a single audio channel. It can be mapped to any other channel output as is, or be mixed with another audio channel. Channel B represents the audio channel that is mixed to the first audio channel before being mapped to an output channel.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation Attenuation A, Attenuation B Audio attenuation can be set for mixed channels only, and will have no effect on a single channel that is not paired with another. Attenuation can be set to: • 0 dB • -3 dB • -6 dB Mix Enable The Mix Enable check box must be checked in order for two audio channels to be mixed. Output Gain The audio Output Gain can be adjusted from -30 dB to 30 dB in 0.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA The Alarm Setup Window Alarms reported to Dashboard Problems detected by the FRS-1002 card are transmitted as alarms to the card’s LED, to the Dashboard interface, and to the optional SNMP monitoring. The problems detected can be reported to the user as minor alarms or critical alarms.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation How to Repurpose your Algogear Card Algogear cards are easy to reconfigure. First, visit our website in the support section, at: http://www.algolith.com/support/downloads/ repurpose-algogear You will find a list of the Algogear products available for you. Select the Algogear solution you would like to download onto your existing Algogear card. Next enter your name and email address and press the Download Solution button.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA Load the new product onto your card The instructions below will help you quickly and easily repurpose your Algogear card with a new Algogear application. Please take the time to read through the steps before beginning the process so that you have all the necessary information on hand before you begin. 1. Repurposing an Algogear card can only be done through the Dashboard software application (to download Dashboard visit http://www.
Guide to installation and operation FRS-1002-MD / FRS-1002-MD-LG-PA 4. Next you will need to upload the downloaded file onto the Algogear card. Click on the Upload button to select the .BIN file in the directory in which it is stored, and click the Open button. Click Upload to get to the .BIN file You will get a confirmation dialog box that displays the selected upload file name, type, size, and the file creation date.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation 5. Be patient! The upgrade process can take a few minutes. While the files are being decompressed, the Dashboard user interface displays an «Upgrade in Progress» message. After decompression, the files are installed and Dashboard loses connection with the card. An error message is then displayed. See graphic below. Card is in the process of being repurposed This step is normal in the upgrade process and must not be interrupted. 6.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation 7. Once the card has rebooted, you should see the name of the new Algogear product you have installed on the dot matrix display located on the board. XVC1001U Dot matrix display ALGOGEAR NOTE: If you don’t see the product name, but instead the following message: “LICENSE?”, an error has occurred with the license file and you should contact Algolith customer support immediately for assistance at 1.877.ALGOLITH ext 3509. 8.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation Congratulations, you have successfully repurposed your Algogear card. To request new rear module labels and card labels, email your name, shipping address, phone number and the Algogear applications you require at support@algolith.com.
FRS-1002-MD / FRS-1002-MD-LG-PA Guide to installation and operation Specifications* SD/HD SDI Video Signal: SD (SMPTE 259M-C) (270 Mbps) HD (SMPTE 292M) (1.485, 1.485/1001 Gbps) Formats: SD 480i59.94, 576i50 HD 720p50, 720p59.94, 720p60, 1080i50, 1080i59.94, 1080i60 Format autodetected Ancillary Data: Passthrough Video Inputs Connectors: Return Loss: Impedance: Video Outputs Connectors: Return Loss: Jitter: Impedance: Reference Connector: Two (2) BNC SD >21 dB up to 270 Mbps HD >14 dB up to 1.
FRS-1002-MD / FRS-1002-MD-LG-PA Limited Warranty Limited Warranty Coverage Algolith Inc. warrants that the equipment it manufactures shall be free from defects in material and workmanship for a period of two (2) years from the date of purchase. If equipment fails due to such defects, Algolith Inc. will, at its option, repair or provide a replacement for the defective part or product.
Guide operation Guid Gu i e to iinstallation id nssta talllllat atio on an and d op operat atio ion FFR FRS-1002-MD RS-1 S-1002 S2-MD D / FR FFRS-1002-MD-LG-PA S-1002 S02-M MDD LG LG-P -PA A 35
