CLOUD 9 LOUNGER Instruction Manual
Assembly Instructions for Cloud 9 Lounger, Model # 4717 Thank you for purchasing the Cloud 9 Lounger. We hope it provides years of enjoyment. Please read and follow assembly and safety instructions for proper assembly and safe use of this product. If you are missing parts or if there are damaged parts, please call our customer service department at 800-295-6758 before returning to the retailer.
HARDWARE Part O Parts P : One 3 ½” 13mm double threaded bolt with two 13mm washers and 2 acorn nuts. Parts Q : Two 2 ¾” x 13mm bolts with two 13 mm lock nuts and four 13mm washers. Parts R : One 3 ¾” x 13mm bolt with one 13 mm lock nut and two 13 mm washers. Parts S: Six plastic bolt caps Part T: Threaded connecting link. Part U: Closed S-hook. Parts V: Four 1 3/8” x 13mm Hex head bolts. Parts W: Two ¾” Hex head bolts. Part X: Hex Wrench Part Y: Hand Knob with square nut. Parts Z: Two Open ended wrenches.
S T E P Part B Step 1: Locate Part A and Part B. Connect Part B to Part A by inserting end of Part B onto swedge end of Part A aligning holes as shown in (Diagram 1). Place a 13mm washer onto Part Q (2 ¾” Bolt) and insert through both Part A & B (Box 1), Place a second 13 mm washer onto bolt and then a 13 mm lock nut (Box 2). Tighten with the open ended wrenches (Part Z) Part A Diagram 1 1 Box 1 Box 2 Box 3 Step 2: Locate Part D.
S T E P Step 4: Locate Parts Y. Insert square nut into nut slot on bottom of O-ring of Part H, as shown in Diagram 3. Then insert hand knob of part Y through the hole of part H as in Box 8. Straighten the Part H assembly so the hand knob is just below the hanging hook as shown in Box 9, then tighten hand knob so Part H stays in place. 4 Box 7 S T E P Box 8 Box 9 Step 5: Place bottom end of Part C over the swedge end of Part B as shown in Box 10.
S T E P Step 7: Locate Parts R (3 ¾” Bolt with 13mm washer) and insert through one of Parts E. Place Part U (Closed S-Hook) onto the bolt Part R as shown in Box 13. Place the second and opposite Part E onto the bolt Part U as shown in Box 14. Place 13 mm washer and 13mm lock nut onto end of Part R and tighten using open ended wrenches (Part Z) as shown in Box 15. 7 Box 13 Box 14 S T E P Box 15 Step 8: Hang Part E assembly to the hanging hook of Part C using the threaded connecting hook (Part T).
S T E P Step 10: Locate Part F. Insert ends of Part F onto swedge ends of both Parts G as shown in Box 19, by pushing down lockpins as in Box 20 until pins are fully engaged in lock holes as shown in Box 21. Part G Part F 10 Box 19 S T E P Box 20 Box 21 Step 11: Locate padded arms Parts J. Attach each Part J to Part E by inserting the 1 3/8” hex bolts through the holes in Part J to the threaded holes located on the outside of parts E as shown in Box 22 & 23.
S T E P Step 13: Locate Part M and place inside seat frame as shown in Box 25. Next, locate black rope (Part K) and attach Part M to seat frame by first threading rope through the middle grommet of Part M and pulling half of the rope through the grommet. Lace Part M with rope over frame and through each grommet working from base on each side until the two rope ends meet at top brace (Part I) as shown in Box 26. Tie the two ends securely around Part I as shown in Box 27 .
S T E P Step 16: Place the plastic protective caps (Part S) over the heads and the nuts on the chair frame as shown in photo. 16 CONGRATULATIONS! Your Cloud 9 Lounger is now complete. FOR YOUR SAFETY • Please always follow the safety instruction and use common sense when using the Cloud 9 Lounger. • The Cloud 9 Lounger is intended for a single user at one time and has a weight capacity of 268 lbs. NEVER EXCEED THE WEIGHT CAPACITY.
