User's Manual

ManualsBrandsAliveal Enterprises ManualsCamera & Photo2.4GHz Wireless Video/Mic. Pen Camera

ALM-2002-9 2.4 GHz Wireless Video/Mic. Pen Camera & Receiver

Master units: 1pc Wireless PecCam, 1pc Receiver, 1pc DC12V adapter, 1pc A/V Cable, 5pcs x 3sets GPA76 batteries.

Accessories: 1pc 9V battery adapter, 1pc 9V alkaline battery, 1pc 9V battery snap, 1pc brass outer body.

SPECIFICATION:

Pen Camera:

Frequency: 4 Channels in 2.4 GHz frequency band

RF output power: EC-R&TTE compliant

Transmitting range: 100M in L-O-S

Built-in Mic.: 30 dB High sensitive Mic.

Power supply: Type 1): DC6V – 7.5V (5pc internal GPA76 batteries)

Type 2): DC9V (1pc 9V auxiliary alkaline battery)

Power consumption: 65 mA

Lens: f=3.7mm / view angle: 70 degrees

Size: 145 mm (L) x 20 mm (W) x 14.5 mm (Dia.)

Weight: 35 Grams

Battery operating time: Type 1): Using 5pcs internal GPA76 batteries is about 50 minutes

Type 2): Using 1pc 9V auxiliary alkaline battery is about 6 hours

Receiver:

Frequency: (4 channels) 2400 – 2483.5 MHz

Video input/output: 1Vp-p/75 ohm

Audio input/output: 0.8V/600 ohm

Antenna: Built-in directional antenna.

Audio bandwidth: 50 –17000 Hz

Operating power: DC12V

Power consumption: 180mA

Size: 150x88x40mm

OPERATING MANUAL OF THE PEN CAMERA:

(㆒) Power Source “Type 1”: Using 5pcs GPA76 Batteries:

(1) Inserting or Changing the Batteries:

Step 1: Turn the pen head (5) to the far right.

Step 2: Take off the pen head (5), rotary tube (6), and metal outer body (7)

Step 3: Take off the cover of the battery cell and insert 5pcs GPA76 batteries,

negative is downward and positive (w/words) is upward.

(2) Switching the Different Channels:

Follow same step 1 and step 2 indicated above

Step 3: Below the battery cell, there is square cell. It is the channel switch.

Using a sharp unit like toothpick to adjust the dip switch in choosing the channel.

(When changing to different channel, in avoiding damage to the delicate channel switcher,

please hold the Ink Cartridge to steady the channels PCB first.)

Channel: 1 (2412MHZ) Channel: 2 (2452MHz) Channel: 3 (2472MHz) Channel: 4 (2432 MHz)

(3) Assemble the Whole Unit:

Step 1: Cover the battery cell (8)

Step 2: Insert the outer body (7).

(There is an indention on top of the metal outer body and there is a fitting convex point on

the pen housing, you can find it just beneath the pen clip. When inserting the outer body,

you have to adjust them to suit for steady holding the outer body to the pen.)

Step 3: Insert the rotary tube (6), and then insert the pen head(5) and tighten it.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCCURLES. OPERATIONS IS SUBJECT TO THE FOLLOWING TOW

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESRIED OPERATION.

Summary of content (2 pages)

PAGE 1
ALM-2002-9 2.4 GHz Wireless Video/Mic. Pen Camera & Receiver Master units: 1pc Wireless PecCam, 1pc Receiver, 1pc DC12V adapter, 1pc A/V Cable, 5pcs x 3sets GPA76 batteries. Accessories: 1pc 9V battery adapter, 1pc 9V alkaline battery, 1pc 9V battery snap, 1pc brass outer body. SPECIFICATION: Pen Camera: Frequency: RF output power: Transmitting range: Built-in Mic.: Power supply: 4 Channels in 2.4 GHz frequency band EC-R&TTE compliant 100M in L-O-S 30 dB High sensitive Mic. Type 1): DC6V – 7.
PAGE 2
(4) Operating the PenCam Kits: PenCam: Step 1: Insert the 5pcs GPA76 batteries to the pen camera as indicated in point (㆒) Step 2: Switch on the same channel as indicated in point (㆓) to suit the receiver channel. Step 3: Assemble the whole unit as indicated in point (㆔) Step 4: Push the button on top of the pen to turn on, push the button again to turn off. (You will find the button that, while on turn off mode, it is slightly higher than when it is in turn on mode.