7500W Generator Table of Contents Topic Warranty 3 Safety Guidelines 5 General 6 Limited 7500WGenerator Page Precautions Battery 15 Assembly 16 Operation 19 Inspection, _ _ii_!iiiiii!ilj ii? i:i!i!ii_iibo!i ¸ i ii_i!_i::ili!_i_01_ii!i!_i; y i i!!;_i!):i ¸ i!_l;Ai:_i HAVE QUESTIONS OR NEED SERVICE Cleaning 25 and Maintenance Installation 26 Compliance 28 Specifications 29 General 30 Parts Listing WARNING! READ AND UNDERSTAND ALL SAFETY PRECAUTIONS IN THIS MANUAL BEFORE OPER
Owner's lVlanual Limited Warranty 7500W Generator Limited Warranty All-Power America warrants to the original purchaser who uses the product in a consumer application (personal, residential or household usage) that all products covered under this warranty are free from defects in material and workmanship for one year from the date of purchase. All products covered by this limited warranty which are used in commercial applications (i.e.
Owner's Manual Safety Guidelines General - Definitions This manual contains important information that you need to know and understand in order to protect YOUR SAFETY and to PREVENT EQUIPMENT PROBLEMS. The following symbols help you recognize this information. Please read the manual and pay attention to these sections. Save These important Safety 7500W Generator _ib Precautions ARNING! FAILURE TO FOLLOW SEVERE INJURY OR DEATH.
Owner's Manual General Precautions Gasoline and Oil (cont'd) (cont'd) General of ignition around the engine and fuel = Keep grounded conductive objects, such as tools, away from exposed, live electrical connections to avoid sparking or arcing. These events could ignite fumes or vapors. parts and Do not refill the fuel tank while the engine is running or while the engine is still hot.
Owner's Manual General Precautions Electrical Safety (cont'd) General (cont'd) Personal = All connections and conduits from the generator to the load must only be installed by trained licensed electricians, and in compliance with all relevant local, state, and federal electrical codes and standards, and other regulations where applicable. - The generator must be earth-grounded for fixed installations electrical codes and standards before operation. - Do not attempt soggy ground.
Owner's lVlanual General Precautions (cont'd) General Servicing Installation Maintain labels and name plates on the generator and engine. These carry important If unreadable or missing, contact All Power America immediately for a replacement. Generator performed service must be performed by unqualified personnel only qualified could repair personnel. Service information. or maintenance result in a risk of injury. When servicing a generator, use only identical replacement parts.
Owner's Manual General Mechanical Precautions General (cont'd) = Do not operate the generator with safety guards removed. attempt to reach around the safety guard for maintenance - Keep hands, arms, long hair, loose clothing, - Keep access and jewelry fast they cannot doors on enclosures closed While the generator is running, or any other reason. away from - Always follow and locked any part of the generator and complete (cont'd) scheduled moving do not parts.
Owner's Manual 7500W Generator Battery Assembly To start generator with electric start you will need a battery (not included). You can use a 12v lawn tractor battery with the following specifications: The dimensions are Wx7.5" Dx5" Hx7" (including terminals). A rated cranking amperage of 200. Terminals are regular, not reversed. Note: Using a battery not designed for this unit may void warranty. Also this generator can also be started with the pull start. Unpacking 1.
Owner's Manual Assembly Handle 7500W Generator Assembly Wheel installation. Start by installing the handle on the frame with two 8ram bolts. Then install the handle retainer as shown. Kit installation Start by _nstalflng the rubber floor mounts Here is the hardware required to _nstafl the support leg. Place a block of wood onto the support leg as shown, Note: The leg should under the generator so that you don't have to hold it up wh_le trying to instafl the leg.
Owner's Manual Operation Fue_ Tank 7500W Generator Operation (cont'd) Starting 1. Turn the engine switch to the ON position. The engine switch enables and disables the ignition system. OFF: To stop the engine RUN: To run the engine Electric Start ! Oil Fill 3ontrol Panel 2. The fuel valve is located between the fuel tank and the carburetor. When the valve lever is in the ON NOTE: THE PARTS MENTIONED BELOW.
Owner's Manual Operation (cont'd) 7500W Generator Operation Powering Starting 4. Operate the Recoil Starter: Turn the key to the "Run" position. Pull the starter grip lightly until you feel resistance, then pull briskly. Return the starter grip gently. Pulling the starter grip operates the recoil starter to crank the engine. ELECTRIC START. For Electric Start just turn the key to start. NOTE: Make sure the adequate battery is installed correctly.
Owner's Manual Operation Powering Operation (cont'd) 12 Volt DC tools and Equipment: Spark 1. Prior to powering tools and equipment, make sure the generator's rated voltage, and amperage capacity (12V DC) is adequate to supply all electrical loads that the unit will power. If powering exceeds the generator's capacity, it may be necessary to group one or more of the tools and/or equipment for connection to a separate generator. 2. Connect _ the power cord of a 12V DC powered tool or equipment 3.
Owner's Manual Inspection, Cleaning, Maintenance WARNING! ALWAYS 7500W Generator Installation and NOTE: MAKE SURE THE ENGINE POWER SWITCH AND ALLOW SUFFiCiENT TiME FOR THE ENGINE AND GENERATOR TO OFF" POSiTiON. DISCONNECT THE SPARK PLUG WiRE FROM THE ENGINE. COMPLETELY COOL BEFORE PERFORMING ANY iNSPECTiONS, MAINTENANCE, OR CLEANING. _ = Before each use, inspect the generator.
Owner's Manual Installation Supporting (cont'd) 7500W Generator Compliance UNITED STATES ENVIRONMENTAL WASHINGTON, DC 20460 and Mounting Mount the generator on a concrete slab capable of supporting the weight of the generator. The slab must extend on all sides beyond the frame by at least one foot. Contact a cement contractor for slab specifications if necessary. Attach the frame to the concrete slab using 3/8" diameter expansion anchor bolts (not supplied).
