Manual

Owner's Manual
Installation
_ OTE: PRIOR TO POWERING TOOLS AND EQUIPMENT MAKE SURE THE
GENERATOR'S RATED VOLTAGE, WATTAGE AND AMPERAGE CAPACITY IS
ADEQUATE TO SUPPLY ALL ELECTRICAL LOADS THAT THE UNIT WILL
POWER. IF POWERING EXCEEDS THE GENERATOR'S CAPACITY, IT MAY BE
NECESSARY TO GROUP ONE OR MORE OF THE TOOLS AND/OR EQUIPMENT
FOR CONNECTION TO A SEPARATE GENERATOR.
Electrical and other permits may be required for the installation of emergency power systems.
Investigate your local building and electrical codes before installing this unit. Installation must be
completed by licensed contractors.
A '
WARNING. THE GENERATOR WEIGHS APPROXIMATELY 100 POUNDS. USE
CARE AND THE PROPER LIFTING OR HOiSTiNG EQUIPMENT WHEN MOVING
IT TO THE INSTALLATION LOCATION. ALWAYS CONNECT HOIST LINES TO
THE FRAME OF THE GENERATOR.
General Location
Make sure to locate and install the generator outdoors where cooling air is readily available.
Install the generator so that the air inlets and outlets are not blocked by obstructions such as
bushes, trees, or snow drifts. Locating it in the path of heavy winds or snowdrifts may require
the placement of a barrier for protection. In normal weather conditions, the air vent should face
the prevailing wind direction.
Install the generator on a concrete slab or other area where rain drainage or flood waters can
not reach it.
Generator placement should allow four feet of access to all sides for maintenance.
Place the generator as close as possible to the electrical tools and equipment being powered to
reduce the length of extension cords.
7500W Generator
Compliance
UNITED STATES ENVIRONMENTAL PROTECTION AGENCY,
WASHINGTON, DC 20460
2010 Model Year Certifcate of Conformity
Manufactare_: Jiangsu Jiangdong Group Co., Ltd.
• Certificate Number: JDG-NRSi-10-12
• Effective Date: 12/23/2009
• Date Issued: 12/23/2009
Merrytin Zaw-Mon, Director, Compliance and Innovation Strategies Division, Office of
Transportation and Air Quality.
Pursuant to Section 213 of Clean Air Act (42 U.S.C. section 7547) and 40 CFR 90, and subiect to
the terms and conditions prescribed in those provisions, this certificate of conformity is hereby
issued for the following small non-road engine family, more fully described in the documentation
required by 40 CFR 90 and produced in the stated model year.
7500W Generator
Installation (cont'd)
Supporting and Mounting
Mount the generator on a concrete slab capable of supporting the weight of the generator, The
slab must extend on all sides beyond the frame by at least one foot, Contact a cement contractor
for slab specifications if necessary, Attach the frame to the concrete slab using 3/8" diameter
expansion anchor bolts (not supplied).
Grounding
_ OTE: IT IS RECOMMENDED THAT ONLY A TRAINED AND LICENSED
ELECTRICIAN PERFORM THIS PROCEDURE
Connect a #6 AWG grounding wire (not included) from the ground connector (8) on the generator
to a grounding rod (not included) that has been driven at least 24 inches deep into the earth, The
grounding rod must be an earth-driven copper or brass rod (electrode) which can adequately
ground the generator,
Owner's Manual
Specifications
AO electrical
Current Output 120V/240V AC @50/25A 60Hz
Continuous/rated Wattage 6000 W
Peak Wattage 7500 W
Outlet Four 120V outlets, OI-_e 120V twisEtock
One 120/240V twistdock
DC electrical
12V 8.3A
Gasoline engine
Type 4_cycle OHV air_cooled recoil & electric starl
Displacement 389cc
Oil capacity 1.16 quart (1.1 liter)
EPA approved yes
Fuel
Type Unleaded gasoline
Capacity 6.6 gallons
Running time 11 hours (approx.) on 1/2 load
Fuel gauge included
Weight
Approximate weight 195 Ibs.
32
This certificate of conformity covers only those new small non-road engines which conform in
all material respects to the design specifications described in the documentation required by 40
CFR 90 and which are produced during the model year stated on this certificate. This certificate
of conformity does not cover small non-road engines imported prior to the effective date of the
certificate. SMALL NON-ROAD ENGINE FAMILY: AJDGS.3892GA
It is a term of this certificate that the manufacturer shall consent to all inspections described in
40 CFR 90.126 and 90.506 and authorized in a warrant or court order. Failure to comply with
the requirements of such a warrant or court order may lead to revocation or suspension of this
certificate for reasons specified in 40 CFR 90. It is also a term of this certifi care that this certificate
may be revoked or suspended or rendered void ab initio for other reasons specified in 40 CFR
Part 90.
This certificate does not cover small non-road engines sold, offered for sale, or introduced, or
delivered for introduction, into commerce in the U.S. prior to the effective date of the certificate.