Product specifications
INSPECTION, MAINTENANCE, AND CLEANING
1
PARTS
LIST
&
ASSEMBLY
DIAGRAM
1.
/7\
WARNING!
Always let the Trigger (36) rest
in
Its
"OFF"
position, remove
the Battery
(37)
from
the
tool,
and
unplug
the
Charger
(39)
from
its electrical
outlet
before performing
any
inspection,
maintenance, or cleaning.
2.
Before each use: Inspect the general
condition
of the lrnpact Wrench. Check for
misalignment
or
binding of moving parts,
cracked
or broken parts, leaking Battery,
damaged Charger wiring, chipped or broken sockets, and
any
other condition that
may
affect
its safe operation.
If
abnormal
noise
or vibration occurs,
have
the prob-
lem corrected before further
use.
Do
not
use
damaged equipment.
3.
Daily: With
a
clean cloth, remove all dirt, grease,
and
oil from the lrnpact Wrench.
Po
not immerse the Impact Wrench in any liquids.
4.
It
may
become necessary
at
sometime
to
replace or clean the two Carbon Brushes
(29)
when the Motor performance decreases,
or
stops working completely.
To
replace the Carbon Brushes:
Remwe
the two Brush Holder Caps
(28).
Then,
remove the two Carbon Brushes
(291,
keeprng
track of the orientation and location
of
each.
If either Carbon Brush is worn more
than
halfway, replace
both
Carbon
Brushes. If the Carbon Brushes are just dirty, however, they may be cleaned by
rubbing them with a pencil eraser.
If
cleaning
and
replacing
used
brushes, try to
install them in the
same
holders and
in
the same direction they were removed. When
installing the Carbon Brushes, make sure the carbon portion of the Carbon Brushes
contact the Motor's Rotor
and
that the spnngs face
away
from
the
Motor. Also,
make
sure the springs operate freely. After replacement or cleaning, replace
the
two Brush
Holder Caps.
NOTE:
New
Carbon Brushes tend
to
arc
or spark when f~rst
used
until they wear
and
conform to the Motor's Rotor.
5.
/!l
CAUTION!
All maintenance, service, or repairs not listed
in
this manual
are
only to
be
attempted
by
a
qualified service technician.
PLEASE READ
THE
FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LlST AND
ASSEMBLY
DIAGRAM IN THIS MANUAL
AS
A REFERENCE
TOOL
ONLY. NEITHER THE MANUFACTURER
OR
DISTRIBUTOR
MAKES
ANY REPRESENTATION
OR
WARRANTY OF ANY KIND
TO
THE BUYER THAT
HE
OR
SHE
IS
QUALIFIED TO MAKE ANY REPAIRS TO
THE
PRODUCT,
OR THAT
HE
OR
SHE IS
QUALIFIED TO REPLACE
ANY
PARTS
OF
THE
PRODUCT
IN FACT,
THE
MANUFACTURER AND/OR
DlSTRlBUTOR EXPRESSLY STATES THAT
ALL
REPAIRS
AND
PARTS REPLACEMENTS SHOULD
BE
UNDERTAKEN
BY
CERTIFIED
AND
LlCENSEDTECHNIC1ANS. AND NOT
BY
THE
BUYER.
THE BUYER
ASSUMES ALL
RISK
AND
LIABILITY ARISING OUT OF HIS
OR
HER REPAIRS TO THE ORIGINAL
PRODUCT
OR
REPLACEMENT PARTS THERETO. OR ARISING OUT
OF
HIS OR HER INSTALLATION
OF
REPLACEMENT PARTS THERETO
APT1
Ol6A-A-22-TB
I
Master
sham
I
APT1011 Sw~tch
APT1
0
16A-A-23-T
R
I
Screw
1
APT1011
Battery
clan
APT1
0Z6A-A-24-TB
I
Right
body
1
?ar
lamlc
gear
f
lhght
head
NOTE:
Some
parts
are
listed
and
shown
for
illustration purposes
only,
and
are
not
aavilable individually
as
replacement
parts.
Page
10
Page
11