Installation Instructions

ManualsBrandsAll-Pro ManualsArea Lights65-Watt Metallic Outdoor Dusk to Dawn Fluorescent Security Area Light

Instruction Manual/Instrucciones

Questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@cooperlighting.com

4. Remove access cover (D) from parts bag.

5. Install the ﬁrst conduit connector and conduit

(sold separately) into the access cover (D).

6. Feed supply wires into conduit and make wiring

connections as described in “Wiring Your Fixture”.

7. Attach access cover (D) to the light ﬁxture (A)

using the two access cover mounting screws (F)

provided (Fig. 1).

NOTE: Make sure all wiring is placed into the arm

prior to tightening the access cover screws (F).

8. Using the three mounting screws (E) provided, bolt

the housing (A) to the mounting surface.

9. Connect second conduit and conduit connector at

the junction box (Fig. 2).

10. Fasten lens assembly (B) to housing (A) using the

two lens assembly lock screws (G) and two washers

(I) provided (Fig. 3).

WIRING YOUR FIXTURE

1. Turn off the power at the main fuse/breaker box.

2. Attach ground wire that is attached to ﬁxture

housing (A) to the junction box earth ground wire.

3. Connect the black ﬁxture wire to the black supply

wire (hot). Attach UL approved wire connector

(sold separately).

4. Connect the white ﬁxture wire to the white supply

wire (neutral). Attach UL approved wire connector

(sold separately).

NOTE: Be careful to connect the wires correctly. Make

sure no bare strands of wire extend from the wire nut or

other approved wire connectors (sold separately).

INSTALLING THE BULB

1. Screw the bulb (C) securely into socket.

2. Back the bulb (C) out one or two turns, then screw

bulb (C) back to insure proper position in socket.

3. Turn power back ON.

INSTALLING THE OPTIONAL LIGHT SHIELD/

REFLECTOR

NOTE: Sometimes ﬁxtures are installed in locations

that receive too much reﬂected light. The photo sensor

may have trouble telling the difference between daylight

and light from the ﬁxture. Also, if the ﬁxture is in a

shadowy location, it may think it is always night time.

The light shield/reﬂector can be used to block or

channel light to the photo sensor.

PACKAGING CONTENTS/CONTENIDO DEL PAQUETE

ITEMS REQUIRED

(Purchase separately)

• Phillips screwdriver

• Adjustable wrench

• Drill with 3/16 in. drill bit

• 1/2 in. diameter ﬂexible conduit (if applicable, length depends on application)

• 1/2 in. watertight conduit connectors (if applicable)

• Wire connectors

WARNINGS AND CAUTIONS

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• For outdoor use only.

• cULus LISTED for wet location use.

• Connect ﬁxture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.

• Fixture should be installed by persons with experience in household wiring or by a qualiﬁed

electrician. The electrical system, and the method of electrically connecting the ﬁxture to it,

must be in accordance with the National Electrical Code and local building codes.

• Always use same wattage and type of bulb that was included with the ﬁxture. Failure to do

so will void the warranty. See ﬁxture for wattage.

• Disconnect at fuse or circuit breaker before installing or servicing.

• Disconnect power and allow ﬁxture to cool before changing bulb or handling ﬁxture.

• Edges may cut. Handle with care.

• Upside down installation can result in overheating or accumulation of water in ﬁxture.

Install right side up.

• MINIMUM 90° C SUPPLY CONDUCTORS.

Notice: Lamps contain mercury, dispose according to local, state, or federal laws. For

more information, visit: www.lamprecycle.org.

MOUNTING YOUR FIXTURE

NOTE: This ﬁxture is intended to be conduit connected to a properly installed and properly

grounded metal weatherproof junction box (not included). All conduit connectors, conduit, and

junction boxes (sold separately) should be UL Listed suitable for wet locations.

1. Using the pattern on the box, mark and drill holes for mounting.

NOTE: Mount this ﬁxture in an upright position.

2. Install the two bottom mounting screws (E) ﬁrst, leaving enough room between the

mounting screws and the mounting surface to accommodate mounting the ﬁxture.

3. Screw the top mounting screw (E) into the predrilled hole and back the screw out. This

will leave the hole threaded and make installation of the ﬁxture easier.

AL65FL

A. Fixture housing with

light sensor

Alojamiento del accesorio

con detector de luz

ENGLISH

E. (3) Mounting screws

(3) Tornillos de montaje

B. One-piece lens

assembly

Ensamblado del

lente de una

sola pieza

C. 65 watt ﬂuorescent bulb

Bombilla ﬂuorescente

de 65 vatios

D. Access cover

Cubierta de

acceso

G. (2) Lens assembly lock screws

(2) Tornillos de ﬁjación del

ensamblado del lente

H. Green ground screw

(attached to ﬁxture)

Tornillo de toma a

tierra verde

(conectado al accesorio)

F. (2) Access cover mounting screws (attached to ﬁxture)

(2) Tornillos de la cubierta de acceso (conectado al accesorio)

I. (2) Washers

(2) Arandelas

J. Light shield/reﬂector (optional)

Escudo de luz/reﬂector (opcional)

Fig. 1

Fig. 2

Conduit

Junction

box

Conduit

connector

Fig. 3

Summary of content (4 pages)

PAGE 1
Instruction Manual/ Instrucciones Questions? /¿Preguntas ? 1-800-334-6871 ConsumerProducts@cooperlighting.com PACKAGING CONTENTS/ CONTENIDO DEL PAQUETE A. Fixture housing with light sensor Alojamiento del accesorio con detector de luz B. One-piece lens assembly C. 65 watt fluorescent bulb Ensamblado del lente de una sola pieza Bombilla fluorescente de 65 vatios E. (3) Mounting screws D. Access cover Cubierta de acceso (3) Tornillos de montaje F.
PAGE 2
1. Turn off the power at the main fuse/breaker box. 2. Loosen, but do not remove, the threaded ring at the top of the photo sensor. 3. Slide the light shield (J) under the threaded ring. 4. Position the light shield/reflector (J) so that it blocks light to sensor or reflects light to the sensor, depending on the problem you are having. 5. Tighten down the threaded ring to hold the light shield/reflector (J) in place (Fig. 4). 6. Turn the power back on. REPLACING THE LIGHT SENSOR 1. 2. 3. 4. 5. 6. 7. 8. 9.
PAGE 3
1. Con la ayuda del patrón en la caja, marque y taladre los agujeros para el montaje. NOTA: Este accesorio debe ser montado en posición vertical. 2. Instale primero los dos tornillos de montaje de la parte inferior (E), dejando suficiente espacio entre los dos tornillos y la superficie de montaje para acomodar el accesorio. 3. Enrosque el tornillo de montaje (E) de la parte superior en el agujero previamente taladrado y sáquelo. Esto dejará el agujero roscado, lo que facilitará la instalación del accesorio.
PAGE 4
Esta garantía no se aplica a los productos de Cooper Lighting que hayan sido alterados o reparados o que estuvieron sujetos a negligencia, abuso, mal uso o accidente (incluso los daños durante el envío). Esta garantía no se aplica a los productos Cooper Lighting no fabricados por Cooper Lighting que hayan sido suministrados, instalados o utilizados junto con los productos Cooper Lighting.