Instructions / Assembly

2
•Ifthextureismountedhigher,theangleofthe
  sensorbelowhorizontalshouldincrease.
5. Walkthroughthedetectionzoneatthefarthestdistanceyouwantyourdetectorto
 detectmotion.
6. AdjusttheSENSITIVITYknobuntilyougetdesiredresults.Formorerange,aimsensor
 slightlyupward.Forlessrange,aimsensorheadslightlydownward.Lightswillturnoff
 4secondsaftermotionstops.
7. Adjustthe“Auto”MODEknobtoatimeselectionfrom1m-12m,dependingonhowmany
 minutesyouwantthexturetostayonaftermotionisdetected.Atdusk,thephotocontrol
 willactivateyourxturetooperateaccordingtothesettingschosen.
NOTE:DecreasingtheSENSITIVITYwilldecreasethedistancetheunitcandetect.
NOTE:Duringdaylighthours,theredLEDindicatorlightwillashwhenmotionisdetected.
Thisisnormal.
SELECTING YOUR DESIRED FEATURE
ENERGY STAR
®
TomeetENERGYSTAR
®
requirements,thephotosensorcontrolknobmustbeinthe“Auto”
modetopreventoperationduringfulldaylight.Maximumlampwattagecannotexceed250watts.
TROUBLESHOOTING
MOUNTING YOUR FIXTURE
NOTE:Universalcoverplatemountstorecessedor
surfacemountedstandardjunctionboxes(Fig.2).
Junctionboxmustbeatleast1-1/2˝indepthforproper
installationforrecessedmountapplication.
NOTE:Forbestperformancewheninstallingmorethan
onePrecisionPlusDopplerRadar™xture:
•Twoormoreunitsmountedsidebyside(facingthe
  samedirection)shouldbeatleast17feetapart.
 •Twounitsfacingeachothershouldbemountedat
  least100feetapart.
 •Fixturecanbewalloreavemounted(Fig.3).
WARNING: Risk of electric shock. Disconnect power
at fuse or circuit breaker before installing or servicing.
1. Lineuptheholesonthemountingbracket(B)with
theholesonyourjunctionbox.Usingeither(2)#6
screwsor(2)#8screws(C)(dependingonthesize
oftheholesinyourjunctionbox),attachthemounting
bracket(B)toyourjunctionbox(Fig.4).
2. Threadxturewiresthroughcoverplategasket(D).
3. Positionthegasket(D)onthecoverplateandconnect
theblackwirefromthexture(A)totheblackhouse
supplywireandthewhitewirefromthexture(A)
tothewhitesupplywireusingthewirenuts(E)
provided.Attachthegroundwirecomingfromyour
housetothecoppergroundwirefromthexture(A)
usingwirenut(E)provided.Ifnohousegroundwire
isavailable,attachthecoppergroundwirefrom
thexture(A)tothejunctionboxifitismetaland
grounded.Ifjunctionboxisnotmetalandnohouse
groundwireisavailable,analternativeground
sourcemustbeusedforsafeoperation(Fig.5).
4. Attachxture(A)tothemountingbracket(B)
usingthemountingplatescrew(F)provided.
Besurenoloosewiresremainstickingoutfrom
underneaththecoverplate.Insertplasticcolor-
matched(G)pluginmountingplatescrewhole
fornishedappearance(Fig.6).
5. Applysiliconecaulkingaroundedgesofcoverplateand
inanyopenholestoprovideawatertightsealfrom
rainandmoisture.
6. Installprotectivelampcovers(H)ontolampholders
byliningupthenipplesonthecovers(H),overthe
lampholderslots.Lockintoplacebytwistingcovers
counterclockwise(Fig.7).
7. Insertgaskets(I)intolampholdersandscrew
bulbsintoeachlampholder(Fig.8).(Donotover
tightenbulbs.)
8. Turnpoweronatmainfuse/breakerbox.
AIMING THE LIGHT
Loosentheknobonthesideofthelampholder.
Tiltlampholderupordowntodesiredposition,then
retightenknob.
WARNING: Deviation from the assembly instructions
may result in a risk of electric shock.
OPERATING YOUR FIXTURE
1. TurnthearrowontheMODEknobto“TEST”fortest
mode(Fig.9).
2. TurnthearrowontheSENSITIVITYknobtoamiddle
pointbetween“+”and“-”.
3. Turnonthepowertothexture(A).Allowxtureto
 warmupapproximately90secondsbeforetesting.
 (Lightsmayormaynotcomeonduringwarm-up
 period;thisisnormal.)
4. Aimsensortowardthegeneraldirectionthatmotion
willbecomingfrom.Maintainatleast1˝ofclearance
betweensensorheadandlamps.Alwaysposition
thesensorheadwithcontrolswitchesfacingtoward
theground.
NOTE: (Sensor Head Placement) Foroptimumdetection,
youmayhavetoexperimentwithaimingandsettings.
Eachlocationwillbedifferentandyourterrainmay
affecttheangleyoursensorneeds.Adjustingtheangle
willchangeyourareaofdetection.Herearesome
generalguidelinestohelpwithsetup:
•8´-12´abovethegroundisagoodrangeforthe
  placementofyourxture.
•Foran8´mountingheight,placingthesensorata
  5°anglebelowhorizontalshouldworkwellfor
  mostlocations(Fig.10).
Fig.2
Octagonal
Round
1-1/2˝
1-1/2˝
Fig.3
Wallmount Eavemount
Fig.4
B
C
C
Fig.7
H
Fig.10
A
5°
ENERGYSTAR
®
issponsoredbytheU.S.
EnvironmentalProtectionAgency&U.S.
DepartmentofEnergy.
Visitwww.energystar.govtolearnmore.
I
A
Fig.8
H
I
H
Mode of MODE Knob How to Set
Operation Adjustment Power Switch
MODEknobarrow
pointstoTEST.
Test Setting
LightsshouldturnONwith
motionbothdayandnight.
LightsshouldturnOFF
after4seconds.
Wall Switch Setting
(connected to fixture)
Keepwallswitch
inONposition.
Motion Activated Setting “Auto”
Lightsshouldturnonwith
motiononlyatnightand
shouldturnOFFafter
1-12min.ofnomotion.
“Auto”MODEknobarrow
pointstoatime
selectionwithinthe
1m-12mtimerange.
Keepwallswitchin
ONposition.
Keepthepower
tothextureON.
Dusk-to-Dawn Setting
(activated only at night)
Lightsshouldstayonfrom
dusktodawnandthenreset
tomotionactivated
settingatthenextdawn.
MODEknobarrow
pointstoatimeselection
withinthe1m-12m
timerange.
Turnthepower
OFF-ON-OFF-ON
within3seconds;lightwill
gointooverridemode.
Return to
Motion Activated Setting
from any of
the above settings.
“Auto”MODEknobarrow
pointstoatimeselection
withinthe1m-12m
timerange.
TurnthepowerOFF
foratleast90seconds
andthenbackON.
Problem Cause / Solution
Outdoor Lights
Do Not Come
On With Motion
At Night
Nopowertothexture.
 • Checkifcircuitbreakertripped.
 • ConrmwallswitchisON.
Bulbisfaulty.
 •Replacebulb.
Surroundingexternalambientlightistoobright.(Ifso,theunitmay
thinkitisdaytime.)
 • Re-aimthehead.
 • Relocateorrepositiontheunitawayfromthelight.
TURN OFF POWER BEFORE CONTINUING
Wiringtotheunitisloose.
 • Checkwiring,andreconnectifnecessaryusingwire
  nuts(E)provided.
Outdoor Lights
Come On For No
Apparent Reason
At Night
Thereismotioninthedetectionzone.
 • Makesurethesensorisnotpickingupmovingobjectssuchas
  trees,trafc,etc.
TEST FOR YOURSELF.
 • Coverthesensorlenswithcardboardtopreventsensorfrom
  detectingmotion.Ifthelightstaysoff,somethinginthedetection
  zoneistriggeringthesensor.
•Ifthisisthecase,reducethesensitivity.
 • Repositionthesensor.
  *Ifthelightstaysonwiththesensorlenscovered,contact
  customerservice.
Unitisinthemotionactivatedsetting.
 •Makesure“Auto”MODEknobissetbetween1m-12m.
Fig.9
Fig.6
G
F
A
Fig.5
E
E
E
D
A