User manual

Chapter 1 Series 1700 Introduction
1-4 ADVANCED MICRO CONTROLS INC
AMCI Compatible Transducers
Table 1.2 lists the AMCI transducers compatible with the 1700 modules.
Model Shaft Mount Turns Comments
R11X-J10/7 0.120” Servo 1 NEMA 1, size 11 resolver
R11X-J12/7 0.188” Servo 1 NEMA 1, size 11 resolver
HT-6 0.188” Front/Side 1 NEMA 13 R11X-J12/7 transducer
HT-20 0.625" Front/Side 1 NEMA 13 heavy duty transducer
HT-20S 0.625" Front/Side 1 HT-20 w/ side mounted connector.
HT-20C 0.625" Front/Side 1
NEMA 4X, stainless steel HT-20, w/ Viton
®
shaft seal,
conduit connector.
HT-20K 0.625" Front/Side 1 NEMA 4X, stainless steel HT-20, w/ Viton shaft seal.
HT-20L 0.625" Front/Side 1 NEMA 4X, stainless steel HT-20, w/ Nitrile shaft seal.
H25-FE 0.375” Flange 1 NEMA 4, size 25, end connector
H25-FS 0.375” Flange 1 NEMA 4, size 25, side connector
H25-FL 0.375” Flange 1 NEMA 4, size 25, integral 15 foot (3 meter) cable
H25-SE 0.375” Servo 1 NEMA 4, size 25, end connector
H25-SS 0.375” Servo 1 NEMA 4, size 25, side connector
H25-SL 0.375” Servo 1 NEMA 4, size 25, integral 15 foot (3 meter) cable
HT-400,
HT-400A,
HT-400B
0.625" Front/Side 1
NEMA 4, HT-20 Bolt-in replacement for Autotech
RL100 transducers. Conduit, Autotech connector, or
AMCI connector styles available.
HT-20-(X) 0.625" Front (X)† HT-20 w/ internal (X):1 gear ratio
HTT-20-1 0.625" Front 1 Redundant single turn resolvers‡
HTT-400-1 0.625" Front 1
Redundant single turn resolvers‡, Bolt-in replacement
for Autotech RL220 transducers.
HTCR-9n-1
0.047"
Cable
Foot 12"
Cable Reel Transducer, 12" span, 0.003" max.
resolution, 45 ft stranded stainless cable standard.
HTCR-9n-6
0.047"
Cable
Foot 76"
Cable Reel Transducer, 76" span, 0.010" max.
resolution, 45 ft stranded stainless cable standard.
HTCR-9n-20
0.047"
Cable
Foot 254"
Cable Reel Transducer, 254" span, 0.032" max.
resolution, 45 ft stranded stainless cable standard.
† Available gear ratios are: 2:1, 2.5:1, 2.77:1, 3:1, 4:1, 4.8:1, 5:1, 6:1, 7:1, 8:1, 9:1, 10:1, 12:1, 13:1, 15:1,
16:1, 20:1, 24:1, 36:1, 40:1, 50:1, 60:1, 64:1, 100:1, 105:1, 150:1,180:1, 250:1 and 256:1
‡ This package contains two resolvers geared 1:1 with the input shaft. Most commonly used in systems that
mandate redundant sensors, AMCI can install two different size 11 resolvers in the package per customer
requirements. Contact AMCI for more information.
Table 1.2 Compatible AMCI Transducers