ALLEN&HEATH ALLEN&HEATH iPS10 POWER ON OFF DIGITAL SYSTEM BACKUP SUPPLY POWER ON ADVANCED POWER SUPPLY TECHNOLOGY iPS10 Digital Console Backup Power Supply USER GUIDE Publication AP6688
Limited Two Year Warranty This product has been manufactured in the UK by ALLEN & HEATH and is warranted to be free from defects in materials or workmanship for a period of two years from the date of purchase by the original owner. To ensure a high level of performance and reliability for which this equipment has been designed and manufactured, read this User Guide before operating.
Important Safety Instructions WARNINGS - Read the following before proceeding : CAUTION ATTENTION: RISQUE DE CHOC ELECTRIQUE – NE PAS OUVRIR Read instructions: Retain these safety and operating instructions for future reference. Adhere to all warnings printed here and on the power supply unit. Follow the operating instructions printed in this User Guide. Do not remove covers: Operate the power supply unit with its covers correctly fitted.
Important Mains plug wiring instructions. The power supply unit is supplied with a moulded mains plug fitted to the AC mains power lead. Follow the instructions below if the mains plug has to be replaced.
Introduction This user guide presents a quick reference to the iPS10 digital console power supply unit. We recommend that you read this fully before starting. Included is information on installing, connecting and operating the power supply unit along with panel drawings and technical specification. Whilst we believe the information in this guide to be reliable we do not assume responsibility for inaccuracies. We also reserve the right to make changes in the interest of further product development.
The iPS10 Power Supply The slimline, 2U rack mountable iPS10 power supply unit is a high performance, low noise, universal mains voltage, switched mode power supply producing the DC voltages required to run the iLive Surface or IDR0 MiniRack. It is available as an option to provide redundant backup of the internal mains power supplies fitted in these iLive components. The iLive will operate with either or both supplies switched on. Two connecting cables are required between the iPS10 and iLive.
Controls and Connections ALLEN&HEATH iPS10 POWER ON OFF POWER ON DIGITAL SYSTEM BACKUP SUPPLY ADVANCED POWER SUPPLY TECHNOLOGY POWER ON/OFF POWER STATUS Press to switch the iPS10 power unit on or off. The internal fan runs at constant speed while the unit is switched on. The blue indicator lights at full brightness while the unit is switched on and working correctly. If the indicator does not light check that mains power is switched on and the IEC mains cord properly inserted.
Connecting the iPS10 to the iLive Surface iLIVE SURFACE Surface CPU power on Internal PSU on Backup PSU on Female plug INTERNAL PSU Cable retention clip DC CABLE 10way Male plug TEMPERATURE MONITOR CABLE CAT5 iPS10 BACKUP PSU MAINS IEC MAINS CABLES Mains power 100 - 240V AC Connecting the iPS10 to the iDR0 MiniRack iDR0 MINIRACK MAINS INTERNAL PSU Female plug DC CABLE 10way Male plug TEMPERATURE MONITOR CABLE CAT5 iPS10 BACKUP PSU MAINS IEC MAINS CABLES Mains power 100 - 240V AC 8 iPS10 User G
Notes on Operating the iPS10 The iPS10 is intended as a backup power supply for iLive system components. At the time of release of this user guide it can be used with any of the 4 surfaces (iLive-80, iLive-112, iLive-144 and iLive176) and the iDR0 DSP MiniRack. These components can operate using their internal mains power units only. Connecting the iPS10 in addition to the internal supply provides dual supply redundancy. The component can be operated with either or both supplies switched on.
Technical specification Technology Switched mode with power factor correction Mains input IEC connector Mains voltage 85 to 250V AC, 47 to 63 Hz ~ Power consumption 320W max Mains fuse T5AL 250V 20mm. DC voltage rails +8, +18, -18, +24, +57 V DC DC output 10-pin female circular chassis mounted socket Temperature sense RJ45 connector DC cable 2.8m multicore male to female. A&H part number 003-576 Temperature cable 2.8m CAT5 RJ45.
