® welcoming • sophisticated • inspiring C US allen + roth® is a registered trademark of LF, LLC. All rights reserved. ITEM #0808356 WALL LANTERN MODEL #41997 ATTACH YOUR RECEIPT HERE Français p. 11 Purchase Date _________________________ Español p. 21 Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-439-9800, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
TABLE OF CONTENTS Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Assembly Instructions. . . . . . . . . . . . . .
PACKAGE CONTENTS A D E B F C PART A B C D E F DESCRIPTION Mounting Bracket (preassembled to Fixture [D]) Mounting Bracket Screw (preassembled to Mounting Bracket [A]) Screw Cap (preassembled to Mounting Screw [B]) Fixture Finial Finial Cap QUANTITY 1 2 2 1 1 1 HARDWARE CONTENTS AA Wire Connector Qty. 3 RR Mounting Screw Qty.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. Failure to do so could lead to electrical shock, fire or other injuries that could be hazardous or even fatal. • Before you begin installing the light, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199.
ASSEMBLY INSTRUCTIONS 1. Turn off the circuit breakers and the wall switch to the supply line leads. 1 DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death. 2. Loosen and remove the screw caps (C) from the mounting bracket screws (B) to remove the mounting bracket (A) from fixture (D). 2 B C D A 3. Attach the mounting bracket (A) to the outlet box (not included) using the mounting screws (RR).
ASSEMBLY INSTRUCTIONS WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fixture are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your house wire is larger than 12-gauge and/or there is more than one house wire to connect to the two fixture lead wires, consult an electrician for the proper size wire connectors to use.
ASSEMBLY INSTRUCTIONS 7. Hang fixture on the two mounting bracket screws (B) and secure with screw caps (C). 7 B 8. Lift the finial cap (F) over the threaded rod at the bottom of the finial (E). Attach to the hole in the top of the fixture (D) by turning the finial (E) in a clockwise direction. C 8 E F 9. Insert the E26-base bulb (not included) into the socket of the fixture (A).
ASSEMBLY INSTRUCTIONS 10. Use weather-proof caulk or sealant (sold separately) around top and sides of mounting plate to prevent water from collecting behind the fixture. 10 11. Restore the power to the circuit breakers and the wall switch to the supply line leads.
OPERATING INSTRUCTIONS 1. Remove the finial (E) and finial cap (F) to access controls for motion activation. When power is first applied the light will initialize for 45 seconds and then will be in Test Mode. The Test Mode will last for 5 minutes. The motion sensor adjustment dials consist of two knobs to adjust Sensitivity and delay Timer. During the Test Mode adjust the sensitivity to the desired distance. After 5 minutes in Test Mode the sensor will enter Auto Mode.
TROUBLESHOOTING PROBLEM Fixture does not light. Fixture stays on continuously. POSSIBLE CAUSE 1. Fixture may be wired incorrectly. CORRECTIVE ACTION 1. Check wiring. 2. Worn or broken bulb. 2. Replace bulb. 3. Fixture is set to Auto Mode. 3. Cover sensor to simulate darkness. 1. Fixture is not set to Auto Mode. 1. Reset fixture by turning the power off and on. 2. There is motion in detection area. 2. Make sure there is no motion in the detection area. 3. Shut-off settings are incorrect. 3.
