Installation Guide

ManualsBrandsallen + roth ManualsVanity LightsNukara 1-Light 27-in Brushed Nickel LED Vanity Light

Model VBL10SBNK

Model VBL10LBNK

ITEM #0760085 / #0760086

#1010728 / #1010729

MODEL#VBL10SBNK / #VBL10LBNK

#VBL10-20BNK / VBL10-20BZ

LED VANITY BAR

VR20213

For Damp

Location

Purchase Date

allen + roth

is a registered trademark

Français p.10

Español p.19

Model VBL10-20BNK

VBL10-20BZ

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

ATTACH YOUR RECEIPT HERE

welcoming • sophisticated • inspiring

Summary of content (9 pages)

PAGE 1
welcoming • sophisticated • inspiring Model VBL10SBNK Model VBL10-20BNK VBL10-20BZ Model VBL10LBNK For Damp Location ITEM #0760085 / #0760086 #1010728 / #1010729 allen + roth® is a registered trademark of LF, LLC. All Rights Reserved. LED VANITY BAR MODEL#VBL10SBNK / #VBL10LBNK #VBL10-20BNK / VBL10-20BZ Français p.10 Español p.19 ATTACH YOUR RECEIPT HERE Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-439-9800, 8 a.m.
PAGE 2
TABLE OF CONTENTS Package Contents ............................................................................................................... 2 Hardware Contents .......................................................................................................................... 3 Safety Information ............................................................................................................... 3 Preparation ...........................................................................
PAGE 3
HARDWARE CONTENTS (shown actual size) AA BB Wire Connector Machine Screw Qty. 3 Qty. 2 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to fire, electrical shock or other injuries that could be hazardous or even fatal.
PAGE 4
SAFETY INFORMATION • To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this light fixture are designed to accept only one 12-gauge house wire and two lead wires from the light fixture. If your house wire is larger than 12-gauge or there is more than one house wire to connect to the corresponding fixture lead wires, consult an electrician for the proper size wire connectors to use.
PAGE 5
PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
PAGE 6
ASSEMBLY INSTRUCTIONS 3. Remove mounting plate (B) from fixture (A) by removing mounting plate screws (C) from the edges of the fixture (A). 3 C A Save mounting plate screws (C) for later use. B C 4. Attach mounting plate (B) to outlet box (not included) using existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult a licensed electrician before proceeding.
PAGE 7
ASSEMBLY INSTRUCTIONS 5. Unwrap BARE fixture wire from BLACK and WHITE fixture wires. Prepare wires by stripping 3/4 in. of insulation from wire ends using wire strippers (not included). Connect WHITE wire from fixture (A) to WHITE wire from outlet box using existing wire connector or wire connector (AA). Connect BLACK wire from fixture (A) to BLACK wire from outlet box using existing wire connector or wire connector (AA).
PAGE 8
ASSEMBLY INSTRUCTIONS 7. Attach fixture (A) to mounting plate (B) using the mounting plate screws (C) previously removed (Step 3, Page 6). 7 NOTE: Before tightening mounting plate screws (C) completely, use level (not included) to check fixture (A) -- adjust if necessary. B C A C 8. Restore power and test fixture (A). 8 If lights do not function, please refer to TROUBLESHOOTING.
PAGE 9
CARE AND MAINTENANCE • Shut off main power supply. Wipe with soft cloth or use window cleaner. Do not use an abrasive cleaner. TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Light does not come on initially or no longer comes on. 1. Power is OFF. 2. Faulty connection. 3. LED component is not working properly. 1. Make sure power supply is ON. 2. Check wiring and all connections. 3. Contact Customer Service.