Installation Guide

ManualsBrandsallen + roth ManualsFloor LampsXHLW2022-4FB

PACKAGE CONTENTS

PART

DESCRIPTION

QUANTITY

PART

DESCRIPTION

QUANTITY

Bottom Plate

Long Tube

Shelf Plate

Socket

Assembly Plate

Short Tube

Top Frame

Fabric Shade

Socket

ITEM #0616080

MODEL #XHLW2022-4FB

FLOOR LAMP

Serial Number

Purchase Date

welcoming • sophisticated • inspiring

allen + roth

is a registered trademark

EB1522

Français p. 9

Español p. 17

Questions, problems, missing parts? Before returning to your retailer, call our customer service

department at 1-866-439-9800, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.

ATTACH YOUR RECEIPT HERE

Lowes.com/allenandroth

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the

product.

WARNING

Do not attempt to replace the bulb while the lamp is plugged into an electrical outlet.

Do not use outdoors or near water or other liquids.

This portable lamp has a polarized plug. One blade is wider than the other as a safety feature to

reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug does

not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never

use with an extension cord unless the plug can be fully inserted. Do not attempt to defeat this

safety feature.

CAUTION

When unpacking and assembling, do not pull on the wire too hard or damage may occur.

Only use the bulb and wattage speciﬁed in these instructions or on the label located on the socket.

Unplug from outlet before removing any parts and cleaning.

Only use a soft cloth for cleaning. Do not use any chemicals or abrasive cleaners.

•

Screw

Qty. 8

Threaded Rod

Qty. 12

Plastic Cap

Qty. 4

Plastic Zip Tie

Qty. 2

HARDWARE CONTENTS (not shown to size)

AA BB CC DD

Hardware Used

Screw

x 4

Hardware Used

Threaded Rod

x 4

Hardware Used

2. Insert the four long tubes (B) onto the bottom

plate (A) and tighten screws (AA) with a Phillips

screwdriver (not included).

Screw

x 4

ASSEMBLY INSTRUCTIONS

4. Place shelf plate (C) onto the exposed ends

of the four threaded rods (BB).

6. Place socket assembly plate (D) onto

the exposed ends of the four threaded rods (BB).

Secure the socket (H) to the socket assembly

plate (D) and by tightening the preassembled

wing nut and washer.

Place bottom plate (A) on the floor.

Insert the four screws (AA) through each of the

four corner holes on the bottom plate (A).

3. Screw four of the threaded rods (BB)

onto the tops of the four long tubes (B).

ASSEMBLY INSTRUCTIONS

PREPARATION

Before beginning assembly of product, make sure all parts are present. Carefully remove all parts

from box and remove all plastic covering the parts. Compare parts with package contents list and

hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Assembly Time: 20 minutes

Tools Required for Assembly (not included): Phillips Screwdriver

Hardware Used

Threaded Rod

x 8

5. Repeat steps 3 and 4 for the remaining

threaded rods (BB), long tubes (B) and shelf plates (C).

Wing Nut

Washer

Screw

x 4

Hardware Used

Plastic Cap

x 4

8. Screw four screws (AA) through the four holes

in the top frame (F) and tighten with a Phillips

screwdriver (not included). Cover the four

recessed holes of the top frame (F) with

plastic caps (CC).

7. Screw the four short tubes (E) onto the exposed

ends of the four threaded rods (BB).

Place the top frame (F) onto the

four short tubes (E).

Plastic Zip Tie

x 2

Hardware Used

9. Unfold fabric shade (G) and insert onto

the socket assembly plate (D) and outside

of the four preassembled anchors. Secure

the power cord with the two plastic zip ties (DD)

to the side tubes of the unit.

Anchor

10. Install bulb (not included). Use 100-watt

max. standard-base incandescent bulb or

23-watt max. standard-base CFL.

The lamp assembly is now complete.

Printed in China

PART PART#DESCRIPTION

Screw

Threaded Rod

Plastic Cap

Plastic Zip Tie

0616080-Screw

0616080-Threaded Rod

0616080-Cap

0616080-Tie

WARRANTY

The manufacturer warrants this product to be free from defects in workmanship and material

present at time of shipment from the factory for one year (1) from the date of purchase. This

warranty applies only to the original purchaser. The manufacturer agrees to correct such defect

at no charge or at our option replace the lamp with a comparable or superior model.

To obtain warranty service, call our customer service department at 1-866-439-9800 for return

authorization and shipping instructions. You may be required to present a copy of your sales

receipt as proof of purchase. All cost of removal and reinstallation are the express responsibility of

the purchaser. Any damage to the lamp by accident, misuse or improper installation, or by afﬁxing

accessories not produced by the manufacturer, are the purchaser’s responsibility. The

manufacturer assumes no responsibility whatsoever for lamp installation during the warranty

period.

There is no further expressed warranty. The manufacturer disclaims any and all implied

warranties. The manufacturer shall not be liable for incidental, consequential or special damages

arising at or in connection with product use or performance except as may otherwise by accorded

by law. This warranty gives you speciﬁc legal rights and you may also have other rights which vary

from state to state. This warranty supersedes all prior warranties.

REPLACEMENT PARTS

For replacement parts, call our customer service department at 1-866-439-9800, 8 a.m. - 6 p.m.,

EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.

allen + roth

is a registered trademark

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

Bulbs will not light. 1. Bulb is burned out.

2. Power is off.

3. Faulty wire connection.

1. Replace light bulb.

2. Make sure power supply is on.

3. Check wiring.

Fuse blows or circult

breaker trips when light

is turned on.

Crossed wires or power is

grounding out.

Check wire connection.

•

CARE AND MAINTENANCE

Clean base with a damp cloth.

Do not use any chemicals, polishes, or abrasives.

Do not immerse fixture in water; doing so will damage the wiring.

11” (H)

8.5” (W)