Installation Washer-Extractors Cabinet Freestanding Refer to Page 6 for Model Identification CFD15C 33, 40, 55 and 75 Models CFD19C CFD19C 18, 25 and 35 Models CFD20C CFD20C 100, 135, 165 and 200 Models Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. 9001000R13 www.comlaundry.
Table of Contents Safety Information.............................................................................. Explanation of Safety Messages........................................................... Important Safety Instructions ............................................................... Safety Decals ........................................................................................ Operator Safety.....................................................................................
Safety Information Explanation of Safety Messages Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.
Safety Information 9. Do not install or store the washer where it will be exposed to water and/or weather. 10. Do not tamper with the controls. 11. Do not repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry out. 12.
Safety Information WARNING CAUTION This machine must be installed, adjusted, and serviced by qualified electrical maintenance personnel familiar with the construction and operation of this type of machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment damage, and may void the warranty. SW004 IMPORTANT: Ensure that the recommended clearances for inspection and maintenance are provided.
Safety Information Operator Safety Do not bypass any safety devices in the machine. WARNING WARNING NEVER insert hands or objects into basket until it has completely stopped. Doing so could result in serious injury. SW012 To ensure the safety of machine operators, the following maintenance checks must be performed daily: Never operate the machine with a bypassed or disconnected balance system.
Introduction Model Identification Information in this manual is applicable to these models: HX18PVQM6 HX18PVQM7 HX18PVXM6 HX18PVXM7 SX18PVPA7 SX18PVQM6 SX18PVQM7 SX18PVXM6 SX18PVXM7 HX25PVQM6 HX25PVQM7 HX25PVXM6 HX25PVXM7 SX25PVQM6 SX25PVQM7 SX25PVXM6 SX25PVXM7 18 25 UX18PVNA6 UX18PVNA7 UX18PVPA6 UX18PVPA7 UX18PVQA6 UX18PVQA7 UX18PVQM6 UX18PVQM7 UX18PVXA6 UX18PVXA7 UX18PVXM6 UX18PVXM7 UX25PVNA6 UX25PVNA7 UX25PVPA6 UX25PVPA7 UX25PVQA6 UX25PVQA7 UX25PVQM6 UX25PVQM7 UX25PVXA6 UX25PVXA7 UX25PVXM6 UX25PVXM
Introduction continued 40 55 75 100 135 165 200 9001000 HX55PVNU6 HX55PVNU7 HX55PVQU6 HX55PVQU7 HX55PVXU6 HX55PVXU7 HX75PVNU6 HX75PVNU7 HX75PVPU7 HX75PVQU6 HX75PVQU7 SX55PVNU6 SX55PVNU7 SX55PVPU6 SX55PVPU7 SX55PVQU6 SX55PVQU7 SX55PVXU6 SX55PVXU7 SX75PVNU6 SX75PVNU7 SX75PVPU7 SX75PVQU6 SX75PVQU7 HX100PVNU6 HX100PVNU7 HX100PVPU7 HX100PVQU6 HX100PVQU7 SX100PVNU6 SX100PVNU7 SX100PVPU7 SX100PVQU6 SX100PVQU7 HX135PVNU6 HX135PVNU7 HX135PVPU7 HX135PVQU6 HX135PVQU7 SX135PVNU6 SX135PVNU7 SX135PVPU7 SX1
Introduction Nameplate Location The nameplate is located at the rear of the machine. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance.
Introduction Model Number Familiarization Guide Sample Model Number: *X55PVXM60001 *X Model Number Prefix 55 Washer-Extractor Capacity (pounds dry weight of laundry) P Type of Electrical Control (P = WE-6 Computer) V Washer-Extractor Speed Capabilities X Electrical Characteristics M6 0001 Design Series Option Identification (varies from machine to machine) * Denotes Brand * X55PVXM60001 12 50 60 55 15 2/3+PE 25 1/3 1000 EXAMPLE OF NAMEPLATE CFD29N CFD29N Figure 2 9001000 © Copyright, A
Specifications and Dimensions General Specifications Model 18 25 33 35 40 Overall width 26 in. (660 mm) 26 in. (660 mm) 30.71 in. (780 mm) 30.8 in. (783 mm) 30.71 in. (780 mm) Overall height 40.6 in. (1031 mm) 40.6 in. (1031 mm) 54.15 in. (1376 mm) 47 in. (1194 mm) 54.15 in. (1376 mm) Overall depth 30.7 in. (780 mm) 34.3 in. (870 mm) 33.07 in. (840 mm) 37.8 in. (960 mm) 37.01 in. (940 mm) Net weight † 465 lb. (211Kg) 520 lb. (236 Kg) 811.30 lb. (368 Kg) 789 lb. (358 Kg) 862.
Specifications and Dimensions General Specifications Model 18 25 33 35 40 1 1 1 1 1 1 HP (0.75 kW) 1 HP (0.75 kW) 2.95 HP (2.2 kW) 2 HP (1.5 kW) 2.95 HP (2.
Specifications and Dimensions General Specifications Model 55 75 100 135 165 200 Overall width 35.4 in. (900 mm) 41.8 in. (1060 mm) 47.3 in. (1200 mm) 47.3 in. (1200 mm) 51.8 in. (1300 mm) 51.8 in. (1300 mm) Overall height 60.8 in. (1544 mm) 61.4 in. (1560 mm) 75.6 in. (1920 mm) 75.6 in. (1920 mm) 82.7 in. (2100 mm) 82.68 in. (2100 mm) Overall depth 40 in. (1016 mm) 46 in. (1168 mm) 52.4 in. (1330 mm) 59.1 in. (1500 mm) 63.8 in. (1620 mm) 71.18 in.
Specifications and Dimensions General Specifications Model 55 75 100 135 165 200 1 1 1 1 1 1 4 HP (3 kW) 5.4 HP (4 kW) 7.4 HP (5.5 kW) 10 HP (7.5 kW) 15 HP (11.
Specifications and Dimensions 5 18: 31 in. (787 mm) 25: 34.8 in. (884 mm) 40.6 in. (1031 mm) 39.8 in. (1011 mm) 20.4 in. (518 mm) 11 in. (279 mm) 19.13 in. (486 mm) 18: 22.05 in. (560 mm) 26 in. (660 mm) 25: 25.98 in. (660 mm) CFD530N CFD530 N 9 in. (229 mm) 8 6 in. (152 mm) 2.9 in. (74 mm) 4 CFS464N CFS464N 1 5.5 in. (140 mm) 2 3 7 6 10 6.2 in. (158 mm) 30.7 in. (780 mm) 29.2 in. (742 mm) 34.7 in. (881 mm) 9 1.6 in. (41 mm) 15.3 in. (389 mm) 2 in. (51 mm) 7.1 in.
Specifications and Dimensions 8.66 in. (220 mm) 10.98 in. (279 mm) 39.8 in. (1011 mm) 40.87 in. (1038 mm) 11 1.3 in. (33 mm) 2.56 in. (65 mm) 1.3 in. (33 mm) 2.56 in. (65 mm) 20.87 in. (530 mm) 25.98 in. (660 mm) 1.18 in. (30 mm) 18: 26.38 in. (670 mm) 25: 30.31 in. (770 mm) CFD521N CFD521N 8.9 in. (226 mm) 5.94 in. (151 mm) 1 2.95 in. (75 mm) 2 3 4 18: 23.23 in. (590 mm) 25: 27.17 in. (690 mm) 2.72 in. (69 mm) 18: 28.62 in. (727 mm) 25: 32.56 in. (827 mm) 5 10 1.18 in.
Specifications and Dimensions 3.47 in. (88 mm) 18.58 in. (472 mm) 54.15 in. (1376 mm) 53.07 in. (1348 mm) 8.66 in. (220 mm) 26.77 in. (680 mm) 1.97 in. (50 mm) 1.97 in. (50 mm) 30.71 in. (780 mm) 1.34 in. (34 mm) 3.41 in. (86.5 mm) CFD537N CFD537N 13.05 in. (332 mm) 10.49 in. (267 mm) 7.93 in. (202 mm) 4.13 in. (105 mm) 1 2 4 26.18 in. (665 mm) 28.86 in. (733 mm) 29.65 in. (753 mm) 1.34 in. (34 mm) CFD538N CFD538N 3 5 6 7 10 1.38 in. (35 mm) 4.3 in. (109 mm) 7.29 in. (185 mm) 39.96 in.
Specifications and Dimensions 5 37.8 in. (960 mm) 47 in. (1194 mm) 46.3 in. (1176 mm) 24.4 in. (620 mm) 15.5 in. (394 mm) 25.16 in. (639 mm) 30.31 in. (770 mm) 30.8 in. (782 mm) CFD531N CFD531N CFS467N CFS467N 12.9 in. (328 mm) 10.4 in. (264 mm) 3.5 in. (89 mm) 8 2 3 4 1 6.1 in. (155 mm) 7 6 10 41 in. (1041 mm) 36.75 in. (934 mm) 38 in. (965 mm) 39.4 in. (1001 mm) 35 in. (889 mm) 9 20 in. (508 mm) 4.4 in. (112 mm) 8 in.
Specifications and Dimensions 11 8.66 in. (220 mm) 14.78 in. (376 mm) 47.32 in. (1202 mm) 46.3 in. (1176 mm) 3.47 in. (88 mm) 1.34 in. (34 mm) 2.6 in. (66 mm) 1.34 in. (34 mm) 25.51 in. (648 mm) 30.71 in.(780 mm) 2.6 in. (66 mm) CFD524N CFD524N 13.05 in. (332 mm) 10.49 in. (267 mm) 7.93 in. (202 mm) 4.13 in. (105 mm) 9 1.44 in. (36.5 mm) 30.12 in. (765 mm) 33.86 in. (860 mm) 3.23 in. 82 mm) 36.06 in. (916 mm) 1.44 in. (36.5 mm) CFD525N CFD525N 1 3 2 10 4 5 8 6 4.3 in. (109.
Specifications and Dimensions 3.47 in. (88 mm) 18.58 in. (472 mm) 54.15 in. (1376 mm) 53.07 in. (1348 mm) 8.66 in. (220 mm) 26.77 in. (680 mm) 1.97 in. (50 mm) 1.97 in. (50 mm) 30.71 in. (780 mm) 1.34 in. (34 mm) 3.41 in. (86.5 mm) CFD537N CFD537N 13.05 in. (332 mm) 10.49 in. (267 mm) 7.93 in. (202 mm) 4.13 in. (105 mm) 1 2 4 30.12 in. (765 mm) 32.8 in. (833 mm) 33.58 in. (853 mm) 1.34 in. (34 mm) CFD538N CFD538N 3 5 6 10 7 1.38 in. (35 mm) 4.3 in. (109 mm) 7.29 in. (185 mm) 39.96 in.
Specifications and Dimensions 5 40 in. (1016 mm) 60.8 in. (1544 mm) 59 in. (1499 mm) 33.8 in. (859 mm) 22 in. (559 mm) 29.13 in. (740 mm) 35.43 in. (900 mm) 32.68 in. (830 mm) 4 in. (102 mm) CFS470N CFD509N CFS470N CFD509N 13.6 in. (91 mm) 10 in. (254 mm) 9.9 in. (252 mm) 6.2 in. (158 mm) 2 3 4 3.9 in. (99 mm) 1 6 7.5 in. (191 mm) 54.7 in. (1389 mm) 11 50.5 in. (1283 mm) 8 7 1.4 in. (36 mm) 28.4 in. (721 mm) 6.5 in. (165 mm) 6.5 in. (165 mm) 9 10 4.1 in. 4.1 in.
Specifications and Dimensions 5 46 in. (1168 mm) 62 in. (1575 mm) 60.3 in. (1532 mm) 33.6 in. (853 mm) 22 in. (559 mm) 4 in. (102 mm) 34.25 in. (870 mm) CFD510N 41.73 in. (1060 mm) 37.8 in. (960 mm) 19.2 in. (488 mm) CFD510N CFS473N CFS473N 14.4 in. (366 mm) 9.7 in. (246 mm) 2 9 in. (229 mm) 3 4 3.7 in. (94 mm) 1 6.9 in. (175 mm) 6 55.4 in. (1407 mm) 7 11 51.75 in. (1315 mm) 8 1.7 in. (43 mm) 22.9 in. (582 mm) 6.7 in. (170 mm) 10 9 4.1 in. (104 mm) CFS474N CFS474N 4.1 in.
Specifications and Dimensions 100: 52.4 in. (1331 mm) 135: 59.3 in. (1506 mm) 6 76.8 in. (1951 mm) 37.8 in. (960 mm) 25.5 in. (648 mm) 4 in. (102 mm) 40.94 in. (1040 mm) 47.24 in. (1200 mm) CFD511N CFD511N 100: 39.76 in. (1010 mm) 12 in. (305 mm) 9.3 in. (2362 mm) 135: 46.65 in. (1185 mm) CFS476N CFS476N 6.9 in. (175 mm) 3.5 in. (89 mm) 4.5 in. (114 mm) 4.1 in. (104 mm) 6.5 in. (165 mm) 2 3 5 6.7 in. (170 mm) 2 in. (51 mm) 9.8 in. (249 mm) 1 8.7 in. (221 mm) 4 9 7 62 in.
Specifications and Dimensions 63.8 in. (1620 mm) 6 82.7 in. (2100 mm) 40.2 in. (1020 mm) 25.25 in. (641 mm) 44.9 in. (1140 mm) 51.2 in. (1300 mm) 4 in. (102 mm) CFD511N CFD511N 14.25 in. (360 mm) 10.75 in. (273 mm) 46.7 in. (1185 mm) 7.8 in. (198 mm) CFD15N CFD15N 4.8 in. (122 mm) 4.5 in. (114 mm) 4.5 in. (114 mm) 2 6.75 in. (172 mm) 2 in. (51 mm) 7.75 in. (197 mm) 3 5 10.24 in. (260 mm) 1 8.7 in. (221 mm) 4 9 7 73 in. (1854 mm) 13 12 8 10 27.4 in. (696 mm) 10 in.
Specifications and Dimensions 6 2.23 in. (56.5 mm) 82.7 in. (2100 mm) 39 in. (993 mm) 23.75 in. (603 mm) 3.19 in. (81 mm) 44.8 in. (1138 mm) 1.73 in. (44 mm) 10.71 in. (272 mm) 3.19 in. (81 mm) 51.18 in. (1300 mm) 53.74 in. (1365 mm) 57.2 in. (1453 mm) 1.73 in. (44 mm) 1.04 in. (26.5 mm) 68.96 in. (175.2 mm) CFD534N CFD533N CFD533N CFD534N 16.06 in. (408 mm) 12.72 in. (323 mm) 9.76 in. (248 mm) 6.81 in. (173 mm) 6.67 in. (169.5 mm) 23 10.12 in. (257 mm) 19.13 in. (486 mm) 10.31 in.
Installation Dimensional Clearances Table 1 shows recommended minimum clearances on all sides of the washer-extractor. Recommended Minimum Clearances Model Minimum rear clearance 18 25 33 35 40 55 75 100 135 165 200 24 in. 24 in. 24 in. 24 in. 24 in. 24 in. 24 in. 24 in. 24 in. 24 in. 24 in. (600 mm) (600 mm) (600 mm) (600 mm) (600 mm) (600 mm) (600 mm) (600 mm) (600 mm) (600 mm) (600 mm) Minimum 6 in. 6 in. 6 in. 6 in. 6 in. 6 in. 6 in. 6 in. 6 in. 6 in. 6 in.
Installation Machine Foundation Thoroughness of detail must be stressed with all foundation work to ensure a stable unit installation, eliminating possibilities of excessive vibration during extract. The washer-extractor must be placed on a smooth level surface so that the entire base of the machine is supported and rests on the mounting surface. The standard installation does not require anchoring unless mandated by state or local codes.
Installation Mechanical Installation Frame Dimensions and Mounting Bolt Location 18, 25, 35, 55, 75, 100, 135 and 165 Pound Capacity with U in the 8th position of the Model Number (e.g. *X18PVXU6) 26 in. (660 mm) 23.38 in. (594 mm) 20.87 in. (530 mm) 1.81 in. (30 mm) 23.23 in. (590 mm) 1.3 in. (33 mm) 22.59 in. (650 mm) 2.56 in. (65 mm) 1.81 in. (30 mm) CFD42N 18 MODEL CFD42N Figure 14 IMPORTANT: Drawing is not to scale.
Installation 26 in. (660 mm) 23.38 in. (594 mm) 1.81 in. (30 mm) 20.87 in. (530 mm) 1.3 in. (33 mm) 2.56 in. (65 mm) 30.79 in. (782 mm) 27.17 in. (690 mm) 1.81 in. (30 mm) CFD44N 25 POUND CFD44N Figure 15 IMPORTANT: Drawing is not to scale.
Installation 1.34 in. (34 mm) 28.86 in. (733 mm) 26.18 in. (665 mm) .87 in. (22 mm) 1.34 in. (34 mm) 26.77 in. (680 mm) 1.97 in. (50 mm) 1.97 in. (50 mm) 30.71 in. (780 mm) CFD541N 33 MODEL CFD541N Figure 16 IMPORTANT: Drawing is not to scale.
Installation 30.70 in. (780 mm) 28 in. (712 mm) 25.51 in. (648 mm) 1.44 in. (36.5 mm) 1.34 in. (34 mm) 1.34 in. (34 mm) 2.6 in. 66 mm) 2.6 in. (66 mm) 33 in. (838 mm) 30.12 in. (765 mm) 1.44 in. (36.5 mm) CFD43N 35 MODEL CFD43N Figure 17 IMPORTANT: Drawing is not to scale.
Installation 1.34 in. (34 mm) 328 in. (833 mm) 30.12 in. (765 mm) .87 in. (22 mm) 1.34 in. (34 mm) 26.77 in. (680 mm) 1.97 in. (50 mm) 1.97 in. (50 mm) CFD542N 30.71 in. (780 mm) 40 MODEL CFD542N Figure 18 IMPORTANT: Drawing is not to scale.
Installation 35.35 in. (898 mm) 1.97 in. (50 mm) 32.68 in. (830 mm) 36.61 in. (930 mm) 1.97 in. (50 mm) 29.13 in. (740 mm) 3.15 in. (80 mm) 3.15 in. (80 mm) CFD45N 55 MODEL CFD45N Figure 19 IMPORTANT: Drawing is not to scale.
Installation 41.73 in. (1060 mm) 2.36 in. (60 mm) 37.8 in. (960 mm) 42.52 in. (1080 mm) 2.36 in. (60 mm) 34.25 in. (870 mm) 3.74 in. (95 mm) 3.74 in. (95 mm) CFD46N 75 MODEL CFD46N Figure 20 IMPORTANT: Drawing is not to scale.
Installation 47.24 in. (1200 mm) 1.57 in. (40 mm) 39.76 in. (1010 mm) 42.91 in. (1090 mm) 1.57 in. (40 mm) 40.94 in. (1040 mm) 3.15 in. (80 mm) 3.15 in. (80 mm) CFD48N 100 MODEL CFD48N Figure 21 IMPORTANT: Drawing is not to scale.
Installation 47.24 in. (1200 mm) 1.67 in. (42.5 mm) 46.65 in. (1185 mm) 50 in. (1270 mm) 1.67 in. (42.5 mm) 40.94 in. (1040 mm) 3.15 in. (80 mm) 3.15 in. (80 mm) CFD47N 135 MODEL CFD47N Figure 22 IMPORTANT: Drawing is not to scale.
Installation 51.2 in. (1300 mm) 1.3 in. (33 mm) 46.7 in. (1185 mm) 49.25 in. (1251 mm) 1.3 in. (33 mm) 44.9 in. (1140 mm) 3.15 in. (80 mm) 3.15 in. (80 mm) CFD47N 165 POUND CFD47N Figure 23 IMPORTANT: Drawing is not to scale.
Installation 44.8 in. (1138 mm) 51.18 in. (1300 mm) 1.73 in. (44 mm) 1.73 in. (44 mm) 44.8 in. (1138 mm) 3.19 in. (81 mm) 3.19 in. (81 mm) 51.18 in. (1300 mm) CFD536N 200 POUND CFD536N Figure 24 IMPORTANT: Drawing is not to scale.
Installation 18, 25 and 35 Pound Capacity with A or M in the 8th position of the Model Number (e.g. *X18PVXA6) 26 in. (660 mm) 2.17 in. (55 mm) 22.05 in. (560 mm) 26.38 in. (670 mm) 2.17 in. (55 mm) 19.13 in. (486 mm) 3.43 in. (87 mm) 3.43 in. (87 mm) CFD49N 18 MODEL CFD49N Figure 25 IMPORTANT: Drawing is not to scale.
Installation 26 in. (660 mm) 2.17 in. (55 mm) 25.98 in. (660 mm) 30.31 in. (770 mm) 2.17 in. (55 mm) 19.13 in. (486 mm) 3.43 in. (87 mm) 3.43 in. (87 mm) CFD51N 25 MODEL CFD51N Figure 26 IMPORTANT: Drawing is not to scale.
Installation 30.8 in. (782 mm) 1.77 in. (45 mm) 30.31 in. (770 mm) 33.85 in. (860 mm) 1.77 in. (45 mm) 25.16 in. (639 mm) 2.78 in. (71 mm) 2.78 in. (71 mm) CFD50N 35 MODEL CFD50N Figure 27 IMPORTANT: Drawing is not to scale.
Installation Mounting Bolt Installation (If Required) 3. Put bolts through the machine in the anchors and fasten them. (For the 18, 25, and 35 models, the diameter of the bolt must be minimum 1/2-13 or 12 mm; for the 33, 40, 55, 75, 100, 135, 165 and 200 models, the diameter of the bolt must be minimum 5/8-11 or 16 mm.) 1 2 4. To level machine, fill the spaces between the machine base and floor with machinery grout. Grout completely under all frame members.
Installation Removing the Transport Brackets To prevent damage during transportation, the machine has been equipped with four red transport brackets (refer to Figure 29 for 18, 25 and 35 models; refer to Figure 30 for 33 and 40 models; refer to Figure 31 for 55 and 75 models [depending on model number]; refer to Figure 32 for 100, 135, 165 and 200 models) to eliminate every possible movement of the tub.
Installation FRONT FRONT 1 1 1 REAR REAR 1 1 33 AND 40 MODELS 1 CFD543N 1 CFS488N 100, 135, 165 AND 200 MODELS Transport Brackets CFS488N 1 Figure 30 Transport Brackets Figure 32 FRONT 1 REAR CFS487N 55 AND 75 MODELS CFS487N 1 Transport Brackets Figure 31 9001000 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 43
Installation Drain Connection A drain system of adequate capacity is essential to washer-extractor performance. Ideally, the water should empty through a vented pipe directly into a sump or floor drain. Figure 33 shows drain line and drain trough configurations. REAR OF MACHINE A flexible connection must be made to a vented or air gap drain system to prevent an air lock and to prevent siphoning. If proper drain size is not available or practical, a surge tank is required.
Installation Drain Information Model 18 25 33 35 40 55 75 100 135 165 200 3 in. (76.2 mm) 3 in. (76.2 mm) 3 in. (76.2 mm) 3 in. (76.2 mm) 3 in. (76.2 mm) 3 in. (76.2 mm) 1 1 1 1 2 2 21.13 32 21.
Installation Water Connection To connect water service to machine with rubber hoses, use the following procedure: WARNING 1. Before installing hoses, flush the water system for at least two minutes. To avoid personal injury, recommended inlet water temperature should be no higher than 125° Fahrenheit (51° Celsius). 2. Check filters in the washer-extractor’s inlet hoses for proper fit and cleanliness before connecting. W709 3. Hang the hoses in a large loop, do not allow them to kink.
Installation Electrical Installation DANGER WARNING Hazardous Voltage. Can cause shock, burn or cause death. Allow machine power to remain off for two minutes prior to working in and around AC inverter drive. Do not use a phase adder on any variablespeed machine. W490 The washer-extractor should be connected to an individual branch circuit not shared with lighting or other equipment. W359 WARNING Hazardous Voltage. Can cause shock, burn or death.
Installation Electrical Specifications 25 33 35 40 55 75 100 135 48 3+PE 6 15 14/2.5 3+N+PE Not available 3+PE Not available 2/3+PE 10 15 14/2.5 3+PE 6 15 14/2.5 3+N+PE Not available 3+PE Not available 2/3+PE 10 15 14/2.5 3+PE 6 15 14/2.5 3+N+PE 18 20 12/4.0 3+PE 18 20 12/4.0 2/3+PE 18 20 12/4.0 3+PE 12 15 14/2.5 3+N+PE Not available 3+PE Not available 2/3+PE 12 15 14/2.5 3+PE 6 15 14/2.5 3+N+PE 18 20 12/4.0 3+PE 18 20 12/4.0 2/3+PE 18 20 12/4.0 3+PE 12 15 14/2.
Installation Table 6 (continued) Electrical Specifications Full Load Amps Circuit Breaker AWG /mm2 50/60 3 3+PE 20 25 10/6.0 P 380-415 50/60 3 3+N+PE 20 25 10/6.0 Q 200-240 50/60 3 3+PE 32 40 8/10.0 N 440-480 50/60 3 3+PE 19 25 10/6.0 P 380-415 50/60 3 3+N+PE 18 25 10/6.0 Q 200-240 50/60 3 3+PE 27 40 8/10.
Installation Electrical Connection Remove the cover plate at the back of the machine. Using copper conductors only, connect the power cable to the connectors. Refer to the instructions listed on the machine’s decal on how to connect the machine. After electrical installation is complete, run the machine through a test cycle and check for clockwise basket rotation during the extract step.
Installation Steam Requirements (Steam Heat Option Only) For washer-extractors equipped with optional steam heat, install piping in accordance with approved commercial steam practices. Steam requirements are shown in Table 7. WARNING Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns. The steam must be turned off and the pipe, connections, and components allowed to cool before the pipe can be touched.
Installation Supply Programming Table When programming a supply step on the WE-8, choose between 9 different supply steps. Refer to Table 8. Supply 1 Turns on the water valve in compartment A of the supply box. Supply 2 Turns on the water valve in compartment B of the supply box. Supply 3 Turns on the water valve in compartment C of the supply box. Supply 4 Activates supply relay 1. Supply 5 Activates supply relay 2. Supply 6 Activates supply relay 3. Supply 7 Activates supply relay 4.
Installation Supply relay 1 controls terminals 1 and 2. Figure 36 shows the jumper wire from terminal 13 (L1 220 VAC) to all other even pins (i.e., 2, 4, 6…). This applies L1 (220 VAC) to terminal 2. When supply 4 on the WE-8 is programmed, this will close supply relay 1 and apply L1 (220 VAC) through pin 2 to pin 1. This signal is used from the terminal to the chemical supply vendors first pump. IMPORTANT: Supply 4 must be programmed on the WE-8 to create the signal on terminal 1.
Installation Out-of-Balance Switch Automatic Lubricator Only for 75-200 Models 1 2 1 2 CFS501N 1 2 Window Probe Figure 40 The out-of-balance switch is mounted on the upper right side on the back of the control panel. There is a window around the probe of the switch that is mounted on the movable part of the machine. When the machine goes out of balance by overloading or uneven distribution of the linen, the out-of-balance switch will interrupt this action to prevent damage to the machine.
Installation Control Function Test b. Close the door without locking it and attempt to start the washer. The washer should not start with the door unlocked. The washer-extractor should be cleaned after the installation is complete. A function test should then be executed on the unloaded machine: c. Close and lock the door and start a cycle. Attempt to open the door while the cycle is in progress. The door should not open. 1.