Programming Washer-Extractors Cabinet Freestanding WE-8 Computer Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) www.comlaundry.com Part No.
WARNING Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and carefulness are factors which cannot be built into these washers.
Table of Contents Introduction......................................................................................... Model Identification ............................................................................. 3 3 Programming ...................................................................................... Setup of the Machine ............................................................................ Version of Control ......................................................................
Introduction Model Identification Information in this manual is applicable to these models: UX18PVXA6 UX18PVXA7 UX18PVXM6 UX18PVXM7 UX18PVXU6 HX018PVQM7 HX018PVXM7 HX18PVQM6 HX18PVQM7 HX18PVQU6 HX18PVXM6 HX18PVXM7 HX025PVQM7 HX025PVXM7 HX25PVQM6 HX25PVQM7 HX25PVQU6 HX25PVXM6 HX25PVXM7 HX18PVXU6 SX018PVPA7 SX018PVQM7 SX018PVXM7 SX18PVPA7 SX18PVQM6 SX18PVQM7 HX25PVXU6 SX025PVQM7 SX025PVXM7 SX25PVQM6 SX25PVQM7 SX25PVQU6 SX25PVXM6 SX18PVQU6 SX18PVXM6 SX18PVXM7 SX18PVXU6 UX018PVNA7 UX018PVPA7 UX018PVQA7 SX25P
Programming Setup of the Machine RUN PROGRAM Program Cycle 00 Turn key from Run to Program To go to the main setup of the machine, press “Auxiliary”, “2”, “9”. System Program _X18PV System Program _X25PV To change the machine type, press the “Advance” button. The following types are possible: _X18PV _X25PV _X33PV _X40PV _X55PV _X75PV _X135PV _X165PV _X200PV Press the “Advance” button until the right type of machine is selected. Press the “Enter” button. Units: English Select the desired units.
Programming Press the “Enter” button to select options. Options : Press the “Aux Fill” button for auxiliary fill option or press “Enter” for heating. Options : Aux Fill If heating is selected, the user can fill in the kW of the electrical heating (example: 9 kW). Heating : 6 kW Press “0”, “9”. Heating : 9 kW Press “Enter” to select advance mode in run mode yes or no. Advance : Yes Press “Advance” to change between yes and no.
Programming Press “Enter” to set the hysteresis level (level at which water drops before it senses it must refill). Level : hyst 2" If English is selected for units, this value will be in inches. If Metric is selected for units, this value will be in cm. Select between 1 to 9 cm or inches. Temp : hyst 3°F Spin retries : 5 Press “Enter” to select the temperature hysteresis (level at which temperature drops before machine senses it must reheat). If English is selected for units, this value will be in °F.
Programming Version of Control To determine control version, apply power to machine. Control will display version of control (i.e., 1.15). Language on Display (Version 1.15 and later ONLY) To set a different language on the WE-8 display: NOTE: If chemical hold is off, then supplies 4 through 9 are controlled exactly like supplies 1 through 3. A switch closure/opening between pins 1 and 4 of the COIN header on the output board will have no effect. Program Storing Mode 1. Turn key from RUN to PROGRAM.
Programming Explanation of the Step Functions Fill: Example: Warm Low (time limit 5 minutes 30 seconds) Choose between 4 water inlet configurations and 3 water levels. Water Inlet Configurations: Cold: Only opens the cold water valve. Hot: Only opens the hot water valve. Warm: Opens the cold and hot water valves. Aux Fill: Opens an auxiliary water valve if installed. Step XX Cycle XX Warm Step XX Cycle XX Warm Low Water Levels: Low: Low water level. Med: Medium water level.
Programming It is possible to more accurately control the temperature of water coming in to the machine during a fill step. This does not apply to “Aux Fill” step. The control will mix the hot and cold water inlet to the temperature programmed in the fill function. To fill in the temperature, select the water inlet type and the water level. Press the “Heat” button and the control will ask the temperature.
Programming Wash: Supply: Choose between 7 different preset wash actions. Choose between 9 different supplies. Wash 1 Wash 2 Wash 3 Wash 4 Wash 5* Wash 6 Wash 7 Action Time (sec) 18 3 0 10 18 4 0 Stop Time (sec) 3 27 0 20 3 56 0 G-force 0.5 0.5 0 0.5 0.5 0.5 0 The “Wash” button is button 4 on the display. Example: Wash 4 for 8 minutes 00 seconds. Supply 1: Turns on the water valve in compartment A of the supply box. Supply 2: Turns on the water valve in compartment B of the supply box.
Programming Chemical Hold Feature Enter time in minutes and press “Enter” (example: 5 min). Chemical supply injection can be paused. Refer to Setup of Chemical Hold Feature. Wash 5 Thermal Cool-Down Immediately after a heat step, a temperature-controlled thermal cool-down may be programmed to prevent fiber shock from sudden cool-down. Step XX Cycle XX 1 hours 05 min The “Heat” button is number 5. Step XX Cycle XX Wash Thermal Cool-Down is Wash 5.
Programming Soak: Example: Soak time of 2 hours with 32°F. Button 7 is the “Soak” button. By pressing button 7, “Soak” will appear on the display. Press “Enter” to fill in the soak time. Example: Soak for 2 hours. Step XX Cycle XX Soak Step XX Cycle XX 0 hours Step XX Cycle XX Soak Step XX Cycle XX 0°F Use the key pad to fill in the soak temperature (example: 32°F). Step XX Cycle XX 32°F Use the key pad to fill in the hours of the soak time (example: 2 hours).
Programming Spin: Drain: Choose between 4 preset spin speeds. This function drains the water. 18-75 Models 100/135 Models 165 Models Spin 1 RPM 500 500 500 Spin 2 RPM 650 650 650 Spin 3 RPM 800 800 750 Spin 4 RPM 1000 80 750 200 Models If you have 2 drains, select which drain has to be opened. Step XX Cycle XX Drain Select Drain 1 or 2. If you only have 1 drain, you can only select 1. Step XX Cycle XX Drain 2 “Spin” is button 9.
Programming Example Making a New Program Program Cycle 00 Program 51 Step 1: Fill warm water to low level (5 minutes 30 seconds time limit) Step 2: Supply 1 and 5 for 20 seconds Step 3: Heat up to 140°F (45 minutes time limit) Step 4: Wash action 4 for 8 minutes 00 seconds Step 5: Drain 1 for 1 minutes 25 seconds Step 6: Spin 3 for 8 minutes 30 seconds To program or edit cycles turn the key into the Program Mode.
Programming Step 01 Cycle 51 Warm Step 01 Cycle 51 Warm Low Step 02 Cycle 51 Supply 1 5 Step 01 Cycle 51 0 min Step 02 Cycle 51 0 min Step 01 Cycle 51 5 min 30 sec Step 02 Cycle 51 0 min 20 sec End End Step 02 9001889 Step 02 Cycle 51 Supply Cycle 51 Cycle 51 Step 03 Cycle 51 Cycle 51 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 15
Programming Step 03 Cycle 51 Heat Step 03 Cycle 51 0°F Step 04 Cycle 51 0 min Step 03 Cycle 51 140°F Step 04 Cycle 51 8 min 00 sec Step 03 Cycle 51 0 hours End Cycle 51 Step 03 Cycle 51 0 hours 45 min Step 05 Cycle 51 End Cycle 51 Step 05 Drain 1 Cycle 51 Step 04 Cycle 51 Step 05 0 min Cycle 51 Step 04 Cycle 51 Wash 16 Step 04 Cycle 51 Wash 4 10/20 Step 05 Cycle 51 1 min 25 sec © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9001889
Programming End Cycle 51 Step 06 Cycle 51 Enter to save ? Program Cycle 51 Step 06 Cycle 51 Spin 1 Step 06 Cycle 51 Spin 3 Step 06 Cycle 51 0 min Step 06 Cycle 51 8 min 30 sec End 9001889 Cycle 51 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 17
Programming Edit a Cycle Program Cycle 00 Change a Complete Step To edit a cycle enter the cycle number (example: cycle 51). Program Cycle 51 Edit Cycle 51 Press the “Edit Cycle” button. Name Cycle 51: Cycle 51 Press the “Enter” button to edit the cycle. Step 01 Cycle 51 Warm Low Press “Enter” to continue. The first step of cycle 51 will display.
Programming Step 02 Cycle 51 Soak Step 02 Cycle 51 0 hours Step 02 Cycle 51 1 hours 00 min Step 02 Cycle 51 1 hours 30 min Step 03 Cycle 51 XXXXXXXX End The control is then in the next step of cycle 51. Press “Advance” until the display shows “End Cycle 55”. Cycle Press “Enter” to confirm. Enter to save ? Press “Enter” to save or “Stop” to ignore the changes.
Programming Program Cycle 00 Changing the Time of a Step To edit a cycle, enter the cycle number (example: cycle 51). Program Cycle 51 Press the “Edit Cycle” button. Edit Cycle 51 Press the “Enter” button to edit the cycle. Name Cycle 51: Cycle 51 Press “Enter” to continue. Step 01 Cycle 51 Warm Low Step 02 Cycle 51 Wash 1 18/3 The first step of cycle 51 will display.
Programming Step 02 Cycle 51 6 min 00 sec Step 02 Cycle 51 6 min 20 sec Press “Enter” to go to the next step. Step 03 Cycle 51 XXXXXXX Press the “Advance” button until display shows “End Cycle 51”. End Cycle 51 Press “Enter” to confirm. Enter to save ? Press “Enter” to save or “Stop” to ignore the changes.
Programming Delete a Step Program Cycle 00 To edit a cycle, enter the cycle number (example: cycle 51). Program Cycle 51 Press the “Edit Cycle” button. Edit Cycle 51 Press the “Enter” button to edit the cycle. Name Cycle 51: Cycle 51 Press “Enter” to continue. Step 01 Cycle 51 Warm Low The first step of cycle 51 will display. Select the step being edited by using the “Advance” button to go to the next step or the “Previous” button to go to the previous step.
Programming Insert a Step Program Cycle 00 To edit a cycle, enter the cycle number (example: cycle 51). Program Cycle 51 Press the “Edit Cycle” button. Edit Cycle 51 Press the “Enter” button to edit the cycle. Name Cycle 51: Cycle 51 Press “Enter” to continue. The first step of cycle 51 will display. Step 01 Cycle 51 Warm Low Select the position where you would like to add a step by using the “Advance” button to go to the next step or the “Previous” button to go to the previous step.
Programming Step 02 Supply Cycle 51 7 Press “Enter” to confirm. Step 02 0 min Cycle 51 Enter the time to activate the supply (example: 0 minutes 23 seconds). Step 02 Cycle 51 0 min 00 sec Step 02 Cycle 51 0 min 23 sec Press “Enter” to confirm. Step 03 Cycle 51 Wash 1 18/3 Press the “Advance” button until “End Cycle 51” is displayed. End Cycle 51 Press “Enter” to confirm. Enter to save ? Press “Enter” to save or “Stop” to ignore the changes.
Programming Program Cycle 00 Delete a Cycle Press the “Erase Cycle” button. Erase Cycle 00 Press the number of the cycle being erased (example: 55). Erase Cycle 55 Press “Enter” to confirm. Enter to save ? Press “Enter” to save or “Stop” to ignore the changes.
Programming Reloading Previous Settings Program Cycle 00 This special function allows previous settings to be restored. Press “Auxiliary”, “3”, “0”. Enter to reload earlier settings The control will ask if earlier settings are desired. Press “Enter” to confirm the settings. NOTE: This function only goes back to the last programming function entered.
Programming Cycle Count Reading Cycle Count Program Cycle xx 1. Enter Program Mode by turning key to PROGRAM position (xx represents a cycle number from 00 to 99). PROGRAM RUN Program Cycle xx 2. Press “Auxiliary” key, then “3” key, then “1” key. Total Working Hours 347 3. The total hours of cycle operation (actual run time) will display. Press “Advance” key to continue. Example display shows 347 total hours (of all cycles). 4. Display now shows total cycle count.
Programming Calibration of the Machine The _x__PV should reflect the size selected in earlier steps. Program Cycle 00 Turn key to Program Mode. Press “Auxiliary”, “3”, “1”. Total working hours : 0 The total hours the machine was running will be displayed. Press “Advance” and screen will show total cycles. Press “Advance” to calibrate the water level sensor. level : 0.0 “ Enter to zero If the value is not zero, press “Enter” and the value will change to zero. Press “Advance” to calibrate the motor.
Programming Speed Calibration This function automatically calibrates water level, distribution speed and spin speed. Calibrate 2 500 rpm Ref: # Offset: # Total working hours : # Coast down Please wait Program Cycle # Total Cycle: # End of Calibration Calibration and testing level: 0.0" Enter to zero If shell is empty of water and display reads 0.0", then press “Add Cycle/Advance”.
Pre-Programmed Cycles Cycle 01 Sheets Light Soil Step 30 Description Cycle 02 Sheets No Bleach Min:sec Step Description Min:sec 1 Hot Fill to Low Level 5:00 1 Hot Fill to Low Level 5:00 2 Supply 1, 2, 4, 5 0:45 2 Supply 1, 4 0:45 3 Wash 1 18/3 (32°F) 7:00 3 Wash 1 18/3 (32°F) 7:00 4 Drain 1 1:00 4 Drain 1 1:00 5 Hot Fill to High Level 5:00 5 Hot Fill to High Level 5:00 6 Wash 1 18/3 (32°F) 2:00 6 Wash 1 18/3 (32°F) 2:00 7 Drain 1 1:00 7 Drain 1 1:00 8 Spin 1
Pre-Programmed Cycles Cycle 03 Towels Light Soil Step Description Cycle 04 Towels No Bleach Min:sec Step Description Min:sec 1 Hot Fill to Low Level 5:00 1 Hot Fill to Low Level 5:00 2 Supply 1, 2, 4, 5 0:45 2 Supply 1, 4 0:45 3 Wash 1 18/3 (32°F) 7:00 3 Wash 1 18/3 (32°F) 7:00 4 Drain 1 1:00 4 Drain 1 1:00 5 Hot Fill to High Level 5:00 5 Hot Fill to High Level 5:00 6 Wash 1 18/3 (32°F) 2:00 6 Wash 1 18/3 (32°F) 2:00 7 Drain 1 1:00 7 Drain 1 1:00 8 Spin 1 1
Pre-Programmed Cycles Cycle 05 Sheets Medium Soil Step 32 Description Cycle 06 Towels Medium Soil Min:sec Step Description Min:sec 1 Hot Fill to Low Level 5:00 1 Hot Fill to Low Level 5:00 2 Supply 1, 4 0:45 2 Supply 1, 4 0:45 3 Wash 1 18/3 (32°F) 6:00 3 Wash 1 18/3 (32°F) 6:00 4 Drain 1 1:00 4 Drain 1 1:00 5 Hot Fill to Low Level 5:00 5 Hot Fill to Low Level 5:00 6 Supply 2, 5 0:45 6 Supply 2, 5 0:45 7 Wash 1 18/3 (32°F) 6:00 7 Wash 1 18/3 (32°F) 6:00 8 Dr
Pre-Programmed Cycles Cycle 07 Blankets Warm Step Description Cycle 08 Spreads Cold Min:sec Step Description Min:sec 1 Warm Fill to High Level 5:00 1 Cold Fill to High Level 5:00 2 Supply 1, 4 0:45 2 Supply 1, 4 0:45 3 Wash 1 18/3 (32°F) 6:00 3 Wash 2 3/27 (32°F) 6:00 4 Drain 1 1:00 4 Drain 1 1:00 5 Warm Fill to High Level 5:00 5 Cold Fill to High Level 5:00 6 Wash 1 18/3 (32°F) 5:00 6 Wash 2 3/27 (32°F) 1:30 7 Drain 1 1:00 7 Drain 1 1:00 8 Spin 1 1:00 8
Pre-Programmed Cycles Cycle 09 Towels Heavy Soil Step 34 Description Cycle 10 Rinse and Spin Min:sec Step Description Min:sec 1 Hot Fill to Low Level 5:00 1 Warm Fill to Low Level 5:00 2 Supply 1, 4 0:45 2 Wash 1 18/3 (32°F) 1:00 3 Wash 1 18/3 (32°F) 7:00 3 Drain 1 1:00 4 Hot Fill to High Level 5:00 4 Spin 1 1:00 5 Supply 2, 5 1:00 5 Spin 4 4:00 6 Wash 1 18/3 (32°F) 7:00 7 Drain 1 1:00 8 Spin 1 1:00 9 Warm Fill to High Level 5:00 10 Wash 1 18/3 (32°F) 2:00
Pre-Programmed Cycles Cycle 11 Health Care Sheets Light Soil Step Description Cycle 12 Health Care Towels Light Soil Min:sec Step Description Min:sec 1 Warm Fill to High Level 5:00 1 Warm Fill to High Level 5:00 2 Wash 1 18/3 (32°F) 2:00 2 Wash 1 18/3 (32°F) 2:00 3 Drain 1, 2, 4, 5 1:00 3 Drain 1 1:00 4 Hot Fill to Low Level 5:00 4 Hot Fill to Low Level 5:00 5 Supply 1, 2 0:45 5 Supply 1, 2, 4, 5 0:45 6 Wash 1 18/3 (32°F) 8:00 6 Wash 1 18/3 (32°F) 8:00 7 Drain 1
Pre-Programmed Cycles Cycle 13 Health Care Sheets Heavy Soil Step 36 Description Cycle 14 Health Care Towels Heavy Soil Min:sec Step Description Min:sec 1 32°F Fill to High Level 5:00 1 32°F Fill to High Level 5:00 2 Wash 1 18/3 (32°F) 2:00 2 Wash 1 18/3 (32°F) 2:00 3 Drain 1 1:00 3 Drain 1 1:00 4 120°F Fill to High Level 5:00 4 120°F Fill to High Level 5:00 5 Wash 1 18/3 (32°F) 2:00 5 Wash 1 18/3 (32°F) 2:00 6 Drain 1, 4 1:00 6 Drain 1 1:00 7 Hot Fill to Low Le
Pre-Programmed Cycles Cycle 15 Health Care Cotton Blankets Step Description Cycle 16 Health Care Diapers Heavy Soil Min:sec Step Description Min:sec 1 110°F Fill to High Level 5:00 1 32°F Fill to High Level 5:00 2 Wash 1 18/3 (32°F) 2:00 2 Wash 1 18/3 (32°F) 2:00 3 Drain 1 1:00 3 Drain 1 1:00 4 Hot Fill to Low Level 5:00 4 Hot Fill to High Level 5:00 5 Supply 1, 2, 4, 5 0:45 5 Wash 1 18/3 (32°F) 2:00 6 Wash 1 18/3 (32°F) 7:00 6 Drain 1 1:00 7 Drain 1 1:00 7 Hot
Pre-Programmed Cycles Cycle 17 Health Care Personal Bleach Step 38 Description Cycle 18 Health Care Personal No Bleach Min:sec Step Description Min:sec 1 Hot Fill to Low Level 5:00 1 Hot Fill to Low Level 5:00 2 Supply 1, 2, 4, 5 0:45 2 Supply 1, 4 0:45 3 Wash 1 18/3 (32°F) 6:00 3 Wash 1 18/3 (32°F) 6:00 4 Drain 1 1:00 4 Drain 1 1:00 5 Hot Fill to High Level 5:00 5 110°F Fill to High Level 5:00 6 Wash 1 18/3 (32°F) 2:00 6 Wash 1 18/3 (32°F) 2:00 7 Drain 1 1:00
Pre-Programmed Cycles Cycle 19 Health Care Pads Polyester Step Description Cycle 20 Table Linen Iron Min:sec Step Description Min:sec 1 110°F Fill to Low Level 5:00 1 110°F Fill to High Level 5:00 2 Supply 1, 4 0:45 2 Wash 1 18/3 (32°F) 2:00 3 Wash 1 18/3 (32°F) 3:00 3 Drain 1 1:00 4 130°F Fill to High Level 5:00 4 Hot Fill to Low Level 5:00 5 Wash 1 18/3 (32°F) 2:00 5 Supply 1, 4 0:45 6 Drain 1 1:00 6 Wash 1 18/3 (32°F) 7:00 7 Hot Fill to Low Level 5:00 7 Drai
Pre-Programmed Cycles Cycle 21 Table Linen No Iron Step 40 Description Cycle 22 Table Color Iron Min:sec Step Description Min:sec 1 110°F Fill to High Level 5:00 1 110°F Fill to High Level 5:00 2 Wash 1 18/3 (32°F) 2:00 2 Wash 1 18/3 (32°F) 2:00 3 Drain 1 1:00 3 Drain 1 1:00 4 Hot Fill to Low Level 5:00 4 Hot Fill to Low Level 5:00 5 Supply 1, 4 0:45 5 Supply 1, 4 0:45 6 Wash 1 18/3 (32°F) 7:00 6 Wash 1 18/3 (32°F) 7:00 7 Drain 1 1:00 7 Drain 1 1:00 8 Hot F
Pre-Programmed Cycles Cycle 23 Table Color No Iron Step Description Cycle 24 Visa Iron Min:sec Step Description Min:sec 1 110°F Fill to High Level 5:00 1 110°F Fill to High Level 5:00 2 Wash 1 18/3 (32°F) 2:00 2 Wash 1 18/3 (32°F) 3:00 3 Drain 1 1:00 3 Drain 1 1:00 4 Hot Fill to Low Level 5:00 4 Hot Fill to Low Level 5:00 5 Supply 1, 4 0:45 5 Supply 1, 4 0:45 6 Wash 1 18/3 (32°F) 7:00 6 Wash 1 18/3 (32°F) 7:00 7 Drain 1 1:00 7 Drain 1 1:00 8 Hot Fill to Low
Pre-Programmed Cycles Cycle 25 Visa No Iron Step 42 Description Cycle 26 Visa Color Iron Min:sec Step Description Min:sec 1 110°F Fill to High Level 5:00 1 110°F Fill to High Level 5:00 2 Wash 1 18/3 (32°F) 3:00 2 Wash 1 18/3 (32°F) 3:00 3 Drain 1 1:00 3 Drain 1, 4 1:00 4 Hot Fill to Low Level 5:00 4 Hot Fill to Low Level 5:00 5 Supply 1, 4 0:45 5 Supply 1 0:45 6 Wash 1 18/3 (32°F) 7:00 6 Wash 1 18/3 (32°F) 7:00 7 Drain 1 1:00 7 Drain 1 1:00 8 Hot Fill to L
Pre-Programmed Cycles Cycle 27 Visa Color No Iron Step Description Cycle 28 Shirt Color Starch Min:sec Step Description Min:sec 1 110°F Fill to High Level 5:00 1 Hot Fill to Low Level 5:00 2 Wash 1 18/3 (32°F) 3:00 2 Supply 1, 4 0:45 3 Drain 1 1:00 3 Wash 1 18/3 (32°F) 7:00 4 Hot Fill to Low Level 5:00 4 Drain 1 1:00 5 Supply 1, 4 0:45 5 Hot Fill to Low Level 5:00 6 Wash 1 18/3 (32°F) 7:00 6 Supply 1, 4 0:45 7 Drain 1 1:00 7 Wash 1 18/3 (32°F) 5:00 8 Hot Fil
Pre-Programmed Cycles Cycle 29 Shirt Bleach Starch Step 44 Description Cycle 30 Shirt Color No Bleach Min:sec Step Description Min:sec 1 Hot Fill to Low Level 5:00 1 Hot Fill to Low Level 5:00 2 Supply 1, 4 0:45 2 Supply 1, 4 0:45 3 Wash 1 18/3 (32°F) 7:00 3 Wash 1 18/3 (32°F) 7:00 4 Drain 1 1:00 4 Drain 1 1:00 5 Hot Fill to Low Level 5:00 5 Hot Fill to Low Level 5:00 6 Supply 2, 5 0:45 6 Supply 1, 4 0:45 7 Wash 1 18/3 (32°F) 7:00 7 Wash 1 18/3 (32°F) 5:00 8
Pre-Programmed Cycles Cycle 31 Shirt Delicate Step Description Cycle 32 Starch Extract Min:sec Step Description Min:sec 1 Warm Fill to Low Level 5:00 1 Warm Fill to Low Level 5:00 2 Wash 2 3/27 (32°F) 2:00 2 Supply 2, 8 0:30 3 Drain 1 1:00 3 Wash 1 18/3 (32°F) 7:00 4 Warm Fill to Low Level 5:00 4 Drain 1 1:00 5 Supply 1, 4 0:45 5 Spin 2 3:00 6 Wash 2 3/27 (32°F) 5:00 7 Drain 1 1:00 8 Warm Fill to High Level 5:00 9 Wash 2 3/27 (32°F) 2:00 10 Drain 1 1:00 11
Pre-Programmed Cycles Cycle 33 Uniforms Bleach Step 46 Description Cycle 34 Uniforms No Bleach Min:sec Step Description Min:sec 1 110°F Fill to High Level 5:00 1 Hot Fill to Low Level 5:00 2 Wash 1 18/3 (32°F) 3:00 2 Supply 1, 4 0:45 3 Drain 1 1:00 3 Wash 1 18/3 (32°F) 6:00 4 Hot Fill to Low Level 5:00 4 Drain 1 1:00 5 Supply 1, 4 0:45 5 110°F Fill to Low Level 5:00 6 Wash 1 18/3 (32°F) 7:00 6 Wash 1 18/3 (32°F) 2:00 7 Drain 1 1:00 7 Drain 1 1:00 8 Hot Fill
Pre-Programmed Cycles Cycle 35 Rags Heavy Soil Step Description Cycle 36 Mops in Bags Min:sec Step Description Min:sec 1 110°F Fill to High Level 5:00 1 110°F Fill to High Level 5:00 2 Wash 1 18/3 (32°F) 2:00 2 Wash 1 18/3 (32°F) 2:00 3 Drain 1 1:00 3 Drain 1 1:00 4 Hot Fill to Low Level 5:00 4 Hot Fill to Low Level 5:00 5 Supply 1, 4 0:45 5 Supply 1, 4 0:45 6 Wash 1 18/3 (32°F) 7:00 6 Wash 1 18/3 (32°F) 7:00 7 Drain 1 1:00 7 Drain 1 1:00 8 Hot Fill to Low L
Pre-Programmed Cycles Cycle 37 Rewash/Reclaim Step 48 Description Cycle 38 Supply Setup Min:sec Step Description Min:sec 1 130°F Fill to High Level 5:00 1 Warm Fill to Low Level 5:00 2 Wash 1 18/3 (32°F) 2:00 2 Supply 1 2:00 3 Drain 1 1:00 3 Supply 2 2:00 4 Hot Fill to Low Level 5:00 4 Supply 3 2:00 5 Supply 1, 2, 4, 5 0:45 5 Supply 4 2:00 6 Wash 1 18/3 (32°F) 4:00 6 Supply 5 2:00 7 Drain 1 1:00 7 Drain 1 1:00 8 Hot Fill to Low Level 5:00 8 Warm Fill to
Pre-Programmed Cycles Cycle 39 Test Program Step Description Cycle 39 Test Program Min:sec Step Description Min:sec 1 Cold Fill to High Level 0:30 36 Wash 1 18/3 (32°F) 0:15 2 Drain 1 0:10 37 Drain 1 1:00 3 Hot Fill to Low Level 5:00 4 Auxiliary Fill to Med Level 5:00 5 Heat (150°F) 1h00 6 Cold Fill to High Level 5:00 7 Supply 1 0:30 8 Supply 2 0:30 9 Supply 3 0:30 10 Supply 4 0:30 11 Supply 5 0:30 12 Drain 1 1:00 13 Warm Fill to Low Level 0:30 14 Supply 6
Pre-Programmed Cycles Cycle 40 Energy Hot Step 50 Description Cycle 41 Energy Warm Min:sec Step Description Min:sec 1 Hot Fill to Low Level 5:00 1 Warm Fill to Low Level 5:00 2 Supply 1, 2 0:15 2 Supply 1, 2 0:15 3 Wash 1 18/3 (32°F) 4:00 3 Wash 1 18/3 (32°F) 4:00 4 Drain 1 1:00 4 Drain 1 1:00 5 Cold Fill to High Level 5:00 5 Cold Fill to High Level 5:00 6 Wash 1 18/3 (32°F) 2:00 6 Wash 1 18/3 (32°F) 2:00 7 Drain 1 1:00 7 Drain 1 1:00 8 Cold Fill to High Le
Pre-Programmed Cycles Cycle 42 Energy Cold Step Description Cycle 50 Normal 95°C Min:sec Step Description Min:sec 1 Cold Fill to Low Level 5:00 1 Warm Fill to Low Level 5:00 2 Supply 1, 2 0:15 2 Supply 1, 4 0:30 3 Wash 1 18/3 (32°F) 4:00 3 Heat (104°F) 1h00 4 Drain 1 1:00 4 Wash 1 18/3 (32°F) 2:00 5 Cold Fill to High Level 5:00 5 Drain 1 1:00 6 Wash 1 18/3 (32°F) 2:00 6 Hot Fill to Low Level 5:00 7 Drain 1 1:00 7 Supply 1, 2, 4, 5 0:30 8 Cold Fill to High Le
Pre-Programmed Cycles Cycle 51 Normal 60°C Step 52 Description Cycle 52 Normal 40°C Min:sec Step Description Min:sec 1 Warm Fill to Low Level 5:00 1 Warm Fill to Low Level 5:00 2 Supply 1, 4 0:30 2 Supply 1, 4 0:30 3 Heat (104°F) 1h00 3 Heat (104°F) 1h00 4 Wash 1 18/3 (32°F) 2:00 4 Wash 1 18/3 (32°F) 2:00 5 Drain 1 1:00 5 Drain 1 1:00 6 Hot Fill to Low Level 5:00 6 Hot Fill to Low Level 5:00 7 Supply 1, 2, 4, 5 0:30 7 Supply 1, 2, 4, 5 0:30 8 Heat (140°F)
Pre-Programmed Cycles Cycle 53 Gentle Cold Step Description Cycle 54 Perm Press 95°C Min:sec Step Description Min:sec 1 Cold Fill to High Level 5:00 1 Warm Fill to Low Level 5:00 2 Supply 1, 4 0:30 2 Supply 1, 4 0:30 3 Wash 2 3/27 (32°F) 2:00 3 Heat (104°F) 1h00 4 Drain 1 1:00 4 Wash 1 18/3 (32°F) 2:00 5 Cold Fill to High Level 5:00 5 Drain 1 1:00 6 Wash 2 3/27 (32°F) 2:00 6 Hot Fill to Low Level 5:00 7 Drain 1 1:00 7 Supply 1, 2, 4, 5 0:30 8 Spin 1 1:00 8
Pre-Programmed Cycles Cycle 55 Perm Press 60°C Step 54 Description Cycle 56 Perm Press 40°C Min:sec Step Description Min:sec 1 Warm Fill to Low Level 5:00 1 Warm Fill to Low Level 5:00 2 Supply 1, 4 0:30 2 Supply 1, 4 0:30 3 Heat (104°F) 1h00 3 Heat (104°F) 1h00 4 Wash 1 18/3 (32°F) 2:00 4 Wash 1 18/3 (32°F) 2:00 5 Drain 1 1:00 5 Drain 1 1:00 6 Hot Fill to Low Level 5:00 6 Hot Fill to Low Level 5:00 7 Supply 1, 2, 4, 5 0:30 7 Supply 1, 2, 4, 5 0:30 8 Heat (
Pre-Programmed Cycles Cycle 57 Gentle 30°C Step Description Min:sec 1 Cold Fill to High Level 5:00 2 Supply 1, 4 0:30 3 Wash 2 3/27 (32°F) 2:00 4 Drain 1 1:00 5 Cold Fill to High Level 5:00 6 Supply 1, 2, 4, 5 0:30 7 Heat (86°F) 1h00 8 Wash 2 3/27 (32°F) 3:00 9 Drain 1 1:00 10 Cold Fill to High Level 5:00 11 Wash 2 3/27 (32°F) 2:00 12 Drain 1 1:00 13 Spin 1 1:00 14 Drain 1 1:00 15 Cold Fill to High Level 5:00 16 Supply 3, 6, 7 0:30 17 Wash 2 3/27 (32°F)
Inverter Drive Error Codes Operation Panel Indication 56 Name Description and NOTES Check point Corrective action Overcurrent shut-off during acceleration When the inverter output current reaches or exceeds approximately 200% of the rated current during acceleration, the protective circuit is activated to stop the inverter output. Check the motor Repair the wiring. cable insulation and connection for output short-circuit/ground fault.
Inverter Drive Error Codes Operation Panel Indication Name Description and NOTES Inverter overload shutoff (electronic overcurrent protection) Check point If a current of more than 150% of the rated Verify that the AC output current flows and overcurrent shut- drive’s parameters are off does not occur (200% or less) inverse- correct. time characteristics cause the electronic overcurrent protection to be activated to stop the inverter output in order to protect the output transistors.
Inverter Drive Error Codes Operation Panel Indication Name Description and NOTES Check point Stall prevention During acceleration–If a current of more (overcurrent) than 150% of the rated inverter current flows in the motor this function stops the increase in frequency until the overload current reduces to prevent the inverter from resulting in overcurrent shut-off. When the overload current has reduces below 150%, this function increases the frequency again.
Inverter Drive Error Codes Operation Panel Indication Name Description and NOTES Under Voltage 9001889 The power supply has fallen below a specified level. Check point This fault appears every time the machine is powered down. Check the power supply voltage. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Corrective action Apply the proper voltage to the machine.