Washer-Extractor Operation/Programming Cabinet Hardmount Instructions for Operating and Programming the S-Series Microcomputer Model Numbers HC25SN SC18SN UC25PN HC80SN SC25SN UC80PN SC27SN SC35SN SC50SN SC80SN NOTA: El manual en español aparece después del manual en inglés. www.comlaundry.com Part No.
Safety Table of Contents Operation/Programming Safety Programming Key to Symbols . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Decal Location . . . . . . . . . . . . . . . . . . . 5 Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . 6 Safe Operating Environment . . . . . . . . . . . . . . 7 Environmental Conditions . . . . . . . . . . . . . 7 Machine Location . . . . . . . . . . . . . . . . . . . . 8 Input and Output Services . . . . . . . . . . . . . 8 Misuse . . . . . . . . . .
© Copyright 2001, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher.
Section 1 Safety Anyone operating or servicing this machine must follow the safety rules in this manual. Particular attention must be paid to the DANGER, WARNING, and CAUTION blocks which appear throughout the manual. The following warnings are general examples that apply to this machine. Warnings specific to a particular installation or maintenance procedure will appear in the manual with the discussion of that procedure.
Safety &$87,21 Ensure that the machine is installed on a level floor of sufficient strength and that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked. SW020 :$51,1* Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns. The steam must be turned off and the pipe, connections, and components allowed to cool before the pipe can be touched.
Safety Safety decals appear at crucial locations on the machine. Failure to maintain legible safety decals could result in injury to the operator or service technician.
Safety To provide personal safety and keep the machine in proper working order, follow all maintenance and safety procedures presented in this manual. If questions regarding safety arise, contact the factory immediately. Use factory-authorized spare parts to avoid safety hazards. Operator Safety 3. Do not attempt to operate the machine if any of the following conditions are present: a. The door does not remain securely locked during the entire cycle. b. Excessively high water level is evident. c.
Safety Safe Operating Environment Safe operation requires an appropriate operating environment for both the operator and the machine. If questions regarding safety arise, contact the factory immediately. Environmental Conditions l Ambient Temperature. Water in the machine will freeze at temperatures of 32° F (0° C) or below. Temperatures above 120° F (50° C) will result in more frequent motor overheating and, in some cases, malfunction or premature damage to solid state devices that are used in some models.
Safety Safe Operating Environment (Continued) Machine Location l Foundation. The concrete floor must be of sufficient strength and thickness to handle the floor loads generated by the high extract speeds of the machine. l Service/Maintenance Space. Provide sufficient space to allow comfortable performance of service procedures and routine preventive maintenance. This is especially important in connection with machines equipped with an AC inverter drive.
Safety Misuse Never use this machine for any purpose other than washing fabric. l Never wash petroleum-soaked rags in the machine. This could result in an explosion. l Never wash machine parts or automotive parts in the machine. This could result in serious damage to the basket. l Never allow children to play on or around this machine. Death or serious injury can result if children become trapped in the machine. Do not leave children unattended while the machine door is open.
Safety Notes 10 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073
Section 2 Operation This manual is designed as a guide to operating and programming the cabinet hardmount washerextractor equipped with the S-Series microcomputer control. Keep the manuals, installation instructions, and the wiring diagrams which accompany the machine in a safe place for ready reference. They have been included with the machine at no charge. Additional copies are available at a nominal charge.
Safety Machine Familiarization Operating Instructions Supply Dispenser S-Series Microcomputer Control On/Off Switch Door Unlock Button Door Handle Button Cold Water Inlet Hot Water Inlet External Chemical Supply System Inlets Input Power Junction Box Vacuum Breaker Drain B011RE3A Figure 2 12 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073
Safety Theory of Operation The design of the machine emphasizes performance reliability and long service life. The cylinder, shell, and main body panels are fabricated of stainless steel. The cylinder on 50-pound capacity machines and smaller is supported with two sealed bearings mounted in a machined cast iron trunnion bolted to a heavy gamma frame.
Safety Theory Of Operation (Continued) S-Computer The S-computer control is a programmable solidstate control capable of storing and running up to 30 cycles. A detailed description of these cycles can be found in the Programming section of this manual under S-computer Standard OPL Cycles. If this machine’s computer has been equipped with special preprogrammed cycles, a separate insert listing these cycles has been included in the resealable plastic bag which contained this manual.
Safety The following table lists the various displays and what they mean. The operator should become familiar with these computer displays. Display Indications Display Meaning Display Meaning S-05 Program identification code (ROM) This is an example only. bFIL Warm fill (both hot and cold) Hold Wait...power has just been turned on. HFIL Hot fill CY Cycle (followed by two-digit number) LOLE Low water level CHEC/CYC* Test cycle selected.
Safety Start-Up Turn on the main power source (circuit breaker or cut-off switch on the wall). An identification code will appear for approximately five seconds. Then the display will flash “hold” for thirty seconds. :$51,1* Never operate the machine with a bypassed or disconnected out-of-balance switch. Operating the machine with severe out-of-balance loads could result in personal injury and serious equipment damage.
Safety Supply Dispenser Cycle Execution Both liquid and powder supplies may be added by raising the flexible cover of the dispenser. Liquid supplies may also be injected directly into the supply dispenser by an external chemical supply system. A cycle can be stopped at any time by pressing the Stop key. The machine will go to the stop routine. When the routine is complete, the door may be unlocked.
Safety Cycle Execution (Continued) If the machine is connected to an external chemical supply system, the programmed supply will begin 10 seconds into the fill. The supply will remain on until the programmed water level is reached, or until 60 seconds have elapsed, whichever happens first.
Safety Drain At the conclusion of a spin, the drain valve opens, and the cylinder turns counterclockwise (forward) at wash speed. This counterclockwise direction mirrors the spin rotation direction and is, therefore, considered forward. Note: The machine should drain in 30 seconds. If the machine fails to drain, contact a qualified service technician. When the water level falls below the low level, there is a 15-second delay, during which the computer continues to monitor water level.
Safety Notes 20 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073
Section 3 Programming The computer board is inside the control module. Near the center of the board is a small toggle switch: this is the RUN/PROGRAM mode switch. :$51,1* Dangerous voltages are present in the electrical control box(es) and at the motor terminals. Only qualified personnel familiar with electrical test procedures, test equipment, and safety precautions should attempt adjustments and troubleshooting.
Safety Cycle Count Time And Temperature Parameters To display the current cycle count, press the Start key while the display is showing the temperature in the sump. The display will show a 2-digit number indicating how many cycles have been run to completion (cycles which were stopped in progress are not counted). Press the Start key to return to PROGRAM mode without resetting the count. Press the Up or Down key to reset the count to zero and return to PROGRAM mode.
Safety 3. Use the Up or Down key to select the desired fill temperature. See the following table for fill options. Fill Temperature Options Display Fill Type CFIL Cold fill HFIL Hot fill bFIL Warm fill 8. Press the Start key. 9. If the machine is equipped with an auxiliary heating system, use the Up or Down key to select the desired segment temperature. To disable auxiliary heat for this segment, set this value to zero. Note: Do not program heat steps for machines not equipped with auxiliary heat.
Safety Cycle Programming (Continued) Supply Dispenser Compartments 2 1 3 11. Use the Up or Down key to select the desired spin time. Set this value to zero to skip the spin step. Press the Start key. The display will now show the identifier for next program segment. 1 2 4 3 Chemical Injection Supply Nozzles Note: An automatic 40-second coast-down follows every high-speed spin. For all spins except the final spin, this coast-down occurs during the fill for the following segment.
Safety Cycle Segment Charts Display Segment 1 (Prewash) Instructions Use the Up or Down key to change. Press the Start key to enter or advance.
Safety Cycle Segment Charts (Continued) Display Segment 2 (Wash) Instructions Use the Up or Down key to change. Press the Start key to enter or advance.
Safety Segments 3 – 7 (Fills 1 – 5) Instructions Display Use the Up or Down key to change. Press the Start key to enter or advance.
Safety Cycle Segment Charts (Continued) Display Segment 8 (Fill 6) Instructions Use the Up or Down key to change. Press the Start key to enter or advance.
Safety Cycle Programming Worksheet Cycle Programming Worksheet Program Prewash Wash Cycle Time (Min) Time (Min) Title Water Water Level Level Supply Supply Temp Temp Spin (Sec) Spin (Sec) Fill 1 Fill 2 Fill 3 Time (Min) Time (Min) Time (Min) Water Water Water Level Level Level Supply Supply Supply Temp Temp Temp Spin (Sec) Spin (Sec) Spin (Sec) Fill 4 Fill 5 Fill 6 Time (Min) Time (Min) Time (Min) Water Water Water Level Level Level Supply Supply Supply T
Safety S-Computer Cycle Charts S-Computer Standard Cycles 1 Light Soil Whites 2 Light Soil Colors 3 Medium Soil Whites 4 Medium Soil Colors 5 Heavy Soil Whites 6 Heavy Soil Colors Time (Min) 0 0 0 2 2 2 Water --- --- --- Cold Hot Cold Level --- --- --- High High High Supply --- --- --- 0 0 0 Temp (F) --- --- --- 0 0 0 Spin (Sec) --- --- --- 0 0 0 Time (Min) 6 6 7 7 5 5 Water Hot Warm Hot Warm Hot Warm Level Low Low Low Low Low Low Supply
Safety S-Computer Standard Cycles (Continued) 1 Light Soil Whites 2 Light Soil Colors 3 Medium Soil Whites 4 Medium Soil Colors 5 Heavy Soil Whites 6 Heavy Soil Colors Time (Min) 0 0 0 0 2 0 Water --- --- --- --- Hot --- Level --- --- --- --- High --- Supply --- --- --- --- 0 --- Temp (F) --- --- --- --- 0 --- Spin (Sec) --- --- --- --- 60 --- Time (Min) 0 0 0 0 2 0 Water --- --- --- --- Hot --- Level --- --- --- --- High --- Supply ---
Safety S-Computer Cycle Charts (Continued) S-Computer Standard Cycles (Continued) 7 Permanent Press Visa 8 Gentle Delicate Wool 9 Rewash Destaining 10 Heavy Soil 11 Rinse Spin 12 Personals Starch Time (Min) 2 2 3 3 0 6 Water Cold Cold Warm Warm --- Warm Level High High High High --- Low Supply 0 0 1 0 --- 1 Temp (F) 0 0 0 0 --- 0 Spin (Sec) 0 0 0 0 --- 0 Time (Min) 2 6 8 6 0 5 Water Warm Cold Hot Hot --- Hot Level High Low Low Low --- Low
Safety S-Computer Standard Cycles (Continued) 7 Permanent Press Visa 8 Gentle Delicate Wool 9 Rewash Destaining 10 Heavy Soil 11 Rinse Spin 12 Personals Starch Time (Min) 2 0 0 3 0 0 Water Warm --- --- Hot --- --- Level High --- --- High --- --- Supply 0 --- --- 0 --- --- Temp (F) 0 --- --- 0 --- --- Spin (Sec) 0 --- --- 0 --- --- Time (Min) 0 0 0 0 0 0 Water --- --- --- --- --- --- Level --- --- --- --- --- --- Supply --- --- --- ---
Safety S-Computer Cycle Charts (Continued) S-Computer Blank Cycle Charts Program 13 14 15 16 17 18 Prewash Time (Min) Water Level Supply Temp (F) Spin (Sec) Wash Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 1 Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 2 Time (Min) Water Level Supply Temp (F) Spin (Sec) 34 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073
Safety S-Computer Blank Cycle Charts (Continued) Program 13 14 15 16 17 18 Fill 3 Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 4 Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 5 Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 6 Time (Min) Water Level Supply Temp (F) Spin (Min) F232073 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 35
Safety S-Computer Cycle Charts (Continued) S-Computer Blank Cycle Charts (Continued) Program 19 20 21 22 23 24 Prewash Time (Min) Water Level Supply Temp (F) Spin (Sec) Wash Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 1 Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 2 Time (Min) Water Level Supply Temp (F) Spin (Sec) 36 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073
Safety S-Computer Blank Cycle Charts (Continued) Program 19 20 21 22 23 24 Fill 3 Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 4 Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 5 Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 6 Time (Min) Water Level Supply Temp (F) Spin (Min) F232073 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 37
Safety S-Computer Cycle Charts (Continued) S-Computer Blank Cycle Charts (Continued) Program 25 26 27 28 29 30 Prewash Time (Min) Water Level Supply Temp (F) Spin (Sec) Wash Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 1 Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 2 Time (Min) Water Level Supply Temp (F) Spin (Sec) 38 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073
Safety S-Computer Blank Cycle Charts (Continued) Program 25 26 27 28 29 30 Fill 3 Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 4 Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 5 Time (Min) Water Level Supply Temp (F) Spin (Sec) Fill 6 Time (Min) Water Level Supply Temp (F) Spin (Min) F232073 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 39
Safety Notes 40 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073
/DYDGRUD H[WUDFWRUD 2SHUDción/Programación de gabinete de montaje permanente Instrucciones de operación y programación de la microcomputadora serie S Números de modelo HC25SN SC18SN UC25PN HC80SN SC25SN UC80PN SC27SN SC35SN SC50SN SC80SN www.comlaundry.com Pieza No.
Contenido Operación/Programación Seguridad Descripción de los símbolos . . . . . . . . . . . . . . . Ubicación de las calcomanías de seguridad . . . Seguridad del operador . . . . . . . . . . . . . . . . . . . Medio ambiente donde usar la máquina sin peligro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Condiciones ambientales . . . . . . . . . . . . . . . Ubicación de la máquina . . . . . . . . . . . . . . Servicios de entrada y salida . . . . . . . . . . . . Uso incorrecto. . . . . . . . .
© Copyright 2001, Alliance Laundry Systems LLC Reservados todos los derechos. Ninguna sección del presente manual puede ser reproducida o transmitida en forma alguna o a través de ningún medio sin el expreso constimiento por escrito del editor.
Sección 1 Seguridad Cualquier persona que use o que dé servicio a esta máquina debe cumplir con las reglas de seguridad que incluimos en este manual. Se debe prestar atención especial a los avisos de PELIGRO, ADVERTENCIA y PRECAUCIÓN que aparecen en todo el manual. PRECAUCIÓN Los siguientes avisos de seguridad son ejemplos generales que se aplican a esta máquina.
Seguridad PRECAUCIÓN Asegúrese de que esta máquina sea instalada sobre un piso nivelado con la suficiente resistencia y de que se mantengan los espacios libres necesarios para la inspección y el mantenimiento. Nunca permita que el espacio para inspección y mantenimiento SW020 quede bloqueado. ADVERTENCIA Nunca toque tuberías, conexiones o componentes internos o externos de vapor. Estas superficies pueden estar demasiado calientes y pueden causar quemaduras graves.
Seguridad Hay calcomanías de seguridad en lugares importantes de la máquina. Si las calcomanías no se mantienen de tal forma que se puedan leer, los P/N 230206 P/N 230877 (Sólo OPL) CAUTION CONNECTION TO WASHER operadores o técnicos de servicio pueden sufrir lesiones. P/N 230215-1 WARNING! HIGH VOLTAGE INSIDE DISCONNECT MAIN POWER BEFORE REMOVING COVER. ONLY SPECIALLY TRAINED PERSONNEL SHOULD TURN POWER ON WHEN COVER IS REMOVED. WARNING ELECTRICIAN High leg must be connected to L-3.
Seguridad Para ofrecer seguridad personal y mantener la máquina funcionando correctamente, cumpla con todos los procedimientos de mantenimiento y seguridad que aparecen en este manual. Si tiene alguna pregunta concerniente a la seguridad, de inmediato póngase en contacto con el fabricante. Use piezas de repuesto autorizadas por el fabricante de esta máquina para evitar situaciones peligrosas. Seguridad del operador 3. No intente usar la máquina si se presenta cualquiera de las siguientes situaciones: a.
Seguridad Medio ambiente donde usar la máquina sin peligro Para que la máquina funcione sin peligro es necesario que el medio ambiente sea adecuado tanto para el operador como para la máquina. Si tiene alguna pregunta concerniente a la seguridad, de inmediato póngase en contacto con el fabricante. Condiciones ambientales l Temperatura ambiente. El agua en la máquina se congela a temperaturas inferiores a 0° C (32° F).
Seguridad Medio ambiente donde usar la máquina sin peligro (continuación) Ubicación de la máquina l Cimentación. El piso de concreto debe tener la resistencia y el espesor necesarios para soportar cargas generadas por las altas velocidades de extracción de la máquina. l Espacio para servicio y mantenimiento. Deje suficiente espacio para realizar procedimientos de servicio y mantenimiento de rutina. Esto es especialmente importante en relación con máquinas equipadas con un mando inversor de CA.
Seguridad Uso incorrecto Nunca use esta máquina con otro propósito que no sea lavar tela. l Nunca lave trapos remojados en petróleo en la máquina. Esto puede ocasionar una explosión. l Nunca lave piezas de maquinaria o de automóviles en la máquina. Esto puede dañar seriamente la canasta. l Nunca permita que los niños jueguen en o cerca de esta máquina. Si algún niño queda atrapado dentro de la máquina pueden sufrir lesiones de gravedad o morir.
Seguridad Notas 52 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073 (SP)
Sección 2 Operación Este manual está diseñado como guía de funcionamiento y programación de la lavadora extractora de gabinete de montaje permanente equipada con el control de una microcomputadora de la serie S. Los manuales, las instrucciones de instalación y los diagramas de cableado que acompañan a esta máquina han sido incluidos con la máquina sin costo para usted. Puede obtener copias adicionales a un costo nominal.
Seguridad Familiarización con la máquina Instrucciones de funcionamiento Surtidor de suministros Control de la microcomputadora de la serie S Interruptor de encendido y apagado Bot—n para quitar el seguro de cierre de la m‡quina Bot—n de la manija de la puerta Entrada de agua fr’a Entrada de agua caliente Entradas del sistema externo de suministros de productos qu’micos Caja de conexiones de corriente de entrada Vacuofreno DesagŸe B011RS3A Figura 2 54 © Copyright, Alliance Laundry Systems LLC –
Seguridad Teoría de funcionamiento El diseño de estas lavadoras extractoras destaca la confianza en el rendimiento y una larga vida de servicio. El cilindro (tambor), la coraza y los paneles del cuerpo principal están fabricados de acero inoxidable. El cilindro (tambor) en las máquinas con capacidad de 50 libras, y las de menor capacidad, está soportado por dos rodamientos sellados instalados sobre un soporte giratorio maquinado en acero al carbón, y sujetado por pernos a una fuerte estructura.
Seguridad Teoría de funcionamiento (continuación) Teclado Tecla Descripción Computadora serie S El control de la computadora serie S es un control de estado sólido capaz de almacenar y preparar hasta 30 ciclos. Una descripción detallada de estos ciclos aparece en la sección de “Programación” de este manual bajo los ciclos estándar de la computadora serie S para lavadoras estándar para lavandería pública en instalaciones.
Seguridad En la siguiente tabla aparecen varios indicadores y sus significados. El operador debe familiarizarse con estos mensajes. Mensajes del indicado Indicador Significado Indicador Significado S-05 Código de identificación del programa (ROM). Éste es sólo un ejemplo. bFIL Llenado con agua tibia (tanto caliente como fría) Hold Esperar... la corriente se acaba de conectar.
Seguridad Arranque Conecte la fuente principal de energía (cortacircuitos o interruptor de corte de corriente en la pared). Aparece un código de identificación durante aproximadamente cinco segundos. Entonces en el indicador aparece la palabra “Hold” (espera) parpadeando durante treinta segundos. El indicador entonces muestra “CY” (ciclo) seguido de un número de ciclo de dos dígitos (01 al 30) para indicar que se puede elegir un ciclo.
Seguridad Surtidor de suministros Ejecución de un ciclo Se pueden agregar suministros tanto líquidos como en polvo levantando la cubierta flexible del surtidor. Los suministros líquidos también se pueden inyectar directamente en el surtidor por medio de un sistema externo de suministro de productos químicos. Se puede detener un ciclo en cualquier momento oprimiendo la tecla Stop (parar). La máquina entonces pasa a la rutina de paro.
Seguridad Ejecución de un ciclo (continuación) Si la máquina se conecta a un sistema externo de suministro de productos químicos, el suministro programado comienza 10 segundos después de que comienza el llenado. El suministro permanece activo hasta que se llega al nivel programado de agua, o hasta que hayan pasado 60 segundos, lo que suceda primero.
Seguridad Desagüe Al final del centrifugado, se abre la válvula de desagüe y el cilindro gira en contra del sentido del reloj (hacia adelante) a la velocidad de lavado. La dirección en contra del sentido del reloj es contraria a la rotación de centrifugado y, por lo tanto, se considera hacia adelante. Nota: La máquina debe vaciarse en 30 segundos. Si la máquina no se vacía, llame a un técnico de servicio.
Seguridad Notas 62 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073 (SP)
Sección 3 Programación El tablero de la computadora está dentro del módulo de control. Cerca de la parte central del tablero existe un pequeño interruptor de palanca: éste es el interruptor de modalidad RUN/PROGRAM (marcha/programación). ADVERTENCIA Existen voltajes peligrosos en las cajas de control eléctrico y en las conexiones del motor.
Seguridad Cuenta de ciclos Parámetros de tiempo y temperatura Para mostrar la cuenta del ciclo actual, oprima la tecla Start (arrancar) mientras el indicador muestra la temperatura en el sumidero. El indicador muestra un número de 2 dígitos que indica cuántos ciclos han terminado completamente. (No se cuentan los ciclos que fueron detenidos mientras estaban llevándose a cabo.) Oprima la tecla Start (arrancar) para volver a la modalidad de programación (PROGRAM) sin llevar la cuenta a ceros.
Seguridad 3. Use la tecla Up (arriba) o la tecla Down (abajo) para seleccionar la temperatura deseada de llenado. Las opciones de llenado aparecen en la siguiente tabla. Opciones de temperatura de llenado Indicador Tipo de llenado CFIL Llenado con agua fría HFIL Llenado con agua caliente bFIL Llenado con agua tibia 4. Oprima la tecla Start (arrancar). 5. Use la tecla Up (arriba) o la tecla Down (abajo) para seleccionar el nivel deseado de llenado. Vea la siguiente tabla.
Seguridad Programación de ciclos (continuación) Compartimientos del surtidor de suministros 11. Use la tecla Up (arriba) o la tecla Down (abajo) para seleccionar el tiempo de centrifugado deseado. Establezca este valor a ceros para omitir el paso de centrifugado. Oprima la tecla Start (arrancar). El indicador ahora muestra el identificador para el siguiente segmento del programa. Nota: Un período automático de disminución de 40 segundos sigue a cada uno de los centrifugados de alta velocidad.
Seguridad Tablas de segmentos de ciclos Segmento 1 (prelavado) Instrucciones Indicador Use la tecla Up (arriba) o la tecla Down (abajo) para cambiar. Oprima la tecla Start (arrancar) para ingresar, registrar o avanzar.
Seguridad Tablas de segmentos de ciclos (continuación) Segmento 2 (lavado) Instrucciones Indicador Use la tecla Up (arriba) o la tecla Down (abajo) para cambiar. Oprima la tecla Start (arrancar) para ingresar, registrar o avanzar.
Seguridad Segmentos 3 al 7 (Llenados 1 al 5) Instrucciones Indicador Use la tecla Up (arriba) o la tecla Down (abajo) para cambiar. Oprima la tecla Start (arrancar) para ingresar, registrar o avanzar.
Seguridad Tablas de segmentos de ciclos (continuación) Segmento 8 (Llenado 6) Instrucciones Indicador Use la tecla Up (arriba) o la tecla Down (abajo) para cambiar. Oprima la tecla Start (arrancar) para ingresar, registrar o avanzar.
Seguridad Hoja de trabajo de programación de ciclos Programa Ciclo Nombre Hoja de trabajo de programación de ciclos Prelavado Lavado Tiempo (min) Tiempo (min) Agua Agua Nivel Nivel Suministro Suministro Temp. Temp. Centrif. (seg) Centrif. (seg) Llenado 1 Llenado 2 Llenado 3 Tiempo (min) Tiempo (min) Tiempo (min) Agua Agua Agua Nivel Nivel Nivel Suministro Suministro Suministro Temp. Temp. Temp. Centrif. (seg) Centrif. (seg) Centrif.
Seguridad Tablas de ciclos de la computadora serie S Ciclos estándar de la computadora serie S 1 Ropa blanca, ligeramente sucia 2 Ropa de color, ligeramente sucia 3 Ropa blanca, medio sucia 4 Ropa de color, medio sucia 5 Ropa blanca, muy sucia 6 Ropa de color, muy sucia Tiempo (min) 0 0 0 2 2 2 Agua --- --- --- fría caliente fría Nivel --- --- --- alto alto alto Suministro --- --- --- 0 0 0 Temp. (F) --- --- --- 0 0 0 Centrif.
Seguridad Ciclos estándar de la computadora serie S (continuación) 1 Ropa blanca, ligeramente sucia 2 Ropa de color, ligeramente sucia 3 Ropa blanca, medio sucia 4 Ropa de color, medio sucia 5 Ropa blanca, muy sucia 6 Ropa de color, muy sucia Tiempo (min) 0 0 0 0 2 0 Agua --- --- --- --- caliente --- Nivel --- --- --- --- alto --- Suministro --- --- --- --- 0 --- Temp. (F) --- --- --- --- 0 --- Centrif.
Seguridad Tablas de ciclos de la computadora serie S (continuación) Ciclos estándar de la computadora serie S (continuación) Programa 7 Planchado permanente Visa 8 9 Ligera Segundo Delicada Lana lavado – Quitar manchas 10 Muy sucia 11 Enjuague – Centrifugado 12 Prendas personales – Almidón Prelavado Tiempo (min) 2 2 3 3 0 6 Agua fría fría tibia tibia --- tibia Nivel alto alto alto alto --- bajo Suministro 0 0 1 0 --- 1 Temp. (F) 0 0 0 0 --- 0 Centrif.
Seguridad Ciclos estándar de la computadora serie S (continuación) Programa 7 Planchado permanente Visa 8 9 Ligera Segundo Delicada Lana lavado – Quitar manchas 10 Muy sucia 11 Enjuague – Centrifugado 12 Prendas personales – Almidón Llenado 3 Tiempo (min) 2 0 0 3 0 0 Agua tibia --- --- caliente --- --- Nivel alto --- --- alto --- --- Suministro 0 --- --- 0 --- --- Temp. (F) 0 --- --- 0 --- --- Centrif.
Seguridad Tablas de ciclos de la computadora serie S (continuación) Tablas de ciclos en blanco de la computadora serie S (continuación) Programa 13 14 15 16 17 18 Prelavado Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Wash Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 1 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 2 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif.
Seguridad Tablas de ciclos en blanco de la computadora serie S (continuación) Programa 13 14 15 16 17 18 Llenado 3 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 4 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 5 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 6 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif.
Seguridad Tablas de ciclos de la computadora serie S (continuación) Tablas de ciclos en blanco de la computadora serie S (continuación) Programa 19 20 21 22 23 24 Prelavado Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Lavado Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 1 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 2 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif.
Seguridad Tablas de ciclos en blanco de la computadora serie S (continuación) Programa 19 20 21 22 23 24 Llenado 3 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 4 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 5 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 6 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif.
Seguridad Tablas de ciclos de la computadora serie S (continuación) Tablas de ciclos en blanco de la computadora serie S (continuación) Programa 25 26 27 28 29 30 Prelavado Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Lavado Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 1 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 2 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif.
Seguridad Tablas de ciclos en blanco de la computadora serie S (continuación) Programa 25 26 27 28 29 30 Llenado 3 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 4 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 5 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif. (seg) Llenado 6 Tiempo (min) Agua Nivel Suministro Temp. (F) Centrif.
Seguridad Notas 82 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073 (SP)