Cabinet Freestanding Installation and Operating Instructions www.comlaundry.com Part No.
Installation/Operation Supplement Table of Contents Safety Information.............................................................................. Important Safety Instructions ............................................................... 2 2 Installation........................................................................................... General Specifications .......................................................................... V-Computer ................................................
Installation/Operation Supplement Safety Information Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer and those maintaining the machine.
Installation/Operation Supplement 9. Do not install or store the washer where it will be exposed to water and/or weather. 10. Do not tamper with the controls. 11. Do not repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry out. 12.
Installation/Operation Supplement Installation General Specifications V-Computer SF18VNV, SF25VNV, UF18VNV, and UF25VNV Models Refer to Table 1. 18 Pound 25 Pound Overall Dimensions Overall width, mm (in.) 737 (29.0) 813 (32.0) Overall height, mm (in.) 1168 (46.0) 1232 (48.5) Overall depth, mm (in.) 833 (32.8) 940 (37.0) Weight and Shipping Information Net weight, kg (lbs.) 250 (550) 318 (700) Domestic shipping weight, kg (lbs.) 250 (550) 341 (750) Domestic shipping volume, m3 (ft3) 0.
Installation/Operation Supplement Table 1 (Continued) 18 Pound 25 Pound Power Consumption Average power used per cycle, kWh 0.2 0.3 Nominal sound emission, dBA 58 Data not available 101 (400) 113 (450) Average HVAC load, kcal/hr (Btu/hr) Drive Train Information Number of motors in drive train Drive motor power, kW (HP) 1 1 0.75 (1.0) 1.50 (2.
Installation/Operation Supplement WE-6 Computer SF35PV, SF50PV, SF85PV, UF35PV, UF50PV, and UF85PV Models Refer to Table 2. 35 Pound 50 Pound 85 Pound Overall width, mm (in.) 889 (35) 990 (39) 1181 (46.5) Overall height, mm (in.) 1407 (55.4) 1514 (59.6Z) 1781 (70.1) Overall depth, mm (in.) 992 (39) 1049 (41.3) 1270 (50) 550 (1212) 726 (1600) 1362 (3000) 572 (1260) 749(1650) 1407 (3100) Domestic shipping volume, m (ft ) 1.80 (63.6) 2.26 (80) 3.
Installation/Operation Supplement Table 2 (Continued) 35 Pound 50 Pound 85 Pound Gentle wash/reverse speed, RPM 26 26 26 Wash/reverse speed, RPM 43 40 41 Distribution/drain speed, RPM 77 73 65 Medium extract speed, RPM 325 305 280 High extract speed l, RPM 475 445 410 High extract speed 2, RPM 610 575 525 High extract speed 3, RPM 960 900 825 Gentle wash/reverse centrifugal force, Gs 0.25 0.29 0.345 Wash/reverse centrifugal force, Gs 0.69 0.68 0.
Installation/Operation Supplement SF135PV, SF250PV, UF135PV, and UF250PV Models Refer to Table 3. 135 Pound Standard 250 Pound Standard Forward Tilt Option Two-Way Tilt Option Overall Dimensions Overall width, mm (in.) 1803 (71) 1957 (77) 2006 (79) 2006 (79) Overall height, mm (in.) 1829 (75) 2083 (82) 2235 (88) 2235 (88) Overall depth, mm (in.) 1537 (60.5) 2235 (88) 2243 (88.3) 2311 91() Weight and Shipping Information Net weight, kg (lbs.
Installation/Operation Supplement Table 3 (Continued) 135 Pound Standard 250 Pound Standard Forward Tilt Option Two-Way Tilt Option Cylinder Speeds 1/2 Wash/reverse speed, RPM 26 21 21 21 Wash/reverse speed, RPM 36 31 31 31 Distribution speed, RPM 62 54 54 54 Medium extract speed, RPM 170 140 140 140 High extract speed l, RPM 375 340 340 340 High extract speed 2, RPM 480 435 435 435 High extract speed 3, RPM 715 650 650 650 Centrifugal Force Data 1/2 Wash/reverse centr
Installation/Operation Supplement Dimensional Clearances NOTE: The dimensions shown here are for planning purposes only. They are approximate and subject to normal manufacturing tolerances. If exact dimensions are required for construction purposes, contact the distributor or manufacturer. We reserve the right to make changes at any time without notice.
Installation/Operation Supplement Dimensions V-Computer SF18VNV, UF18VNV, SF25VNV, and UF25VNV Models G D H A B C E K L F J Front I Left Side M N S O R Q P Rear CFS452N CFS425N Figure 1 F232148 (EN) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 11
Installation/Operation Supplement 12 18 Pound 25 Pound A 659 mm (26 in.) 686 mm (27 in.) B 492 mm (19-13/32 in.) 508 mm (20 in.) C 440 mm (17-5/16 in.) 432 mm (17 in.) D 1161 mm (45-23/32 in.) 1232 mm (48-1/2 in.) E 686 mm (27 in.) 762 mm (30 in.) F 737 mm (29 in.) 813 mm (32 in.) G 18 mm (23/32 in.) 18 mm (23/32 in.) H 1143 mm (45 in.) 1214 mm (47-13/16 in.) I 25 mm (1 in.) 25 mm (1 in.) J 774 mm (30-1/2 in.) 876 mm (34-1/2 in.) K 709 mm (27-15/16 in.) 816 mm (32-1/8 in.
Installation/Operation Supplement WE-6 Computer SF35PV and UF35PV Models 814 mm (32") 638 mm (25 1/10") 559 mm (22") 889 mm (35") 992 mm (39") Front Side 828 mm (32 3/5") 1 813 mm (32") 2 606 mm (23 9/10") 3 1408 mm (55 2/5") 1255 mm (49 2/5") 1323 mm (52 1/10") 1031 mm (40 3/5") 300 mm (11 4/5") 5 209 mm (8 1/5") 279 mm (11") 4 B145I Rear B145I 1 2 3 Cold Water Hot Water Steam Inlet 4 5 76 mm (3 in.) Reuse Drain Outlet 76 mm (3 in.
Installation/Operation Supplement SF50PV, UF50PV, SF85PV, and UF85PV Models A B C D E Front Side 1 2 F G 3 H I J N M 5 K L 4 Rear B146I B146I 1 2 3 Cold Water Hot Water Steam Inlet 4 5 76 mm (3 in.) Reuse Drain Outlet 76 mm (3 in.
Installation/Operation Supplement 50 Pound 85 Pound A 872 mm (34-3/10 in.) 1054 mm (41-1/2 in.) B 26-1/5 in. (666 mm) 831 mm (32-7/10 in.) C 582 mm (22-9/10 in.) 765 mm (30-1/10 in.) D 991 mm (39 in.) 1181 mm (46-1/2 in.) E 1049 mm (41-3/10 in.) 1270 mm (50 in.) F 930 mm (36-3/5 in.) 1107 mm (43-3/5 in.) G 889 mm (35 in.) 1083 mm (42-3/5 in.) H 619 mm (24-2/5 in.) 758 mm (29-9/10 in.) I 1513 mm (59-3/5 in.) 1781 mm (70-1/10 in.) J 1399 mm (55-1/10 in.) 1685 mm (66-2/5 in.
Installation/Operation Supplement 135 Pound Capacity Models 1905 mm (75") 1664 mm (65 1/2") 1060 mm (41 3/4") 768 mm (30 1/4") 1575 mm (62") 1803 mm (71") 718 mm (28 1/4") 1549 mm (61") 1491 mm (58 11/16") Front 1457 mm (57 5/16") 992 mm (39 3/32") 913 mm (35 29/32") Side 1 1376 mm (54 3/16") 2 3 4 5 6 952 mm (37 1/2") 584 mm (23") 529 mm (20 13/16") 10 9 1468 mm (57 13/16") 1803 mm (71") 1430 mm (56 5/16") 1435 mm (56 1/2") 171 mm (6 3/4") 1715 mm (67 1/2") 509 mm (20 1/16") 521
Installation/Operation Supplement 250 Pound Capacity Models 721 mm (28 3/8") 559 mm (22") 1034 mm (40 11/16") 483 mm (19") 2083 mm (82") 1207 mm (47 1/2") 1740 mm (68 1/2") 829 mm (32 5/8") 1957 mm (77 1/16") 292 mm (11 1/2") Front 784 mm (30 7/8") 1829 mm (72") 10 912 mm (35 29/32") 2037 mm (80 3/16") 1744 mm (68 11/16") 1639 mm (64 1/2") 1198 mm (47 3/16") 483 mm (19") Side 1615 mm (63 5/8") 1 2 3 4 5 1096 mm (43 3/16") 6 712 mm (28") 9 1997 mm (78 5/8") 1960 mm (77 3/16") 158
Installation/Operation Supplement 250 Pound Capacity Models with Forward Tilt or Two-Way Tilt Option H I J A B G F E C K D 1 L Front 2 3 M Side 4 N 5 O P 9 Q R 8 AA S T Z Y U X 7 V W 6 Rear CFS456N R074IE3A 1 2 3 4 5 Recirculation Port Extra Fill Valve Hot Water Inlet Vent Cold Water Inlet 6 7 8 9 Drain Outlet Reuse Drain Outlet External Supply Signal Main Power Figure 6 18 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232148 (EN)
Installation/Operation Supplement A B Forward Tilt Two-Way Tilt 2235 mm (88 in.) 2235 mm (88 in.) 1736 mm (74-13/32 in.) 1736 mm (74-13/32 in.) C 1930 mm (76 in.) 1930 mm (76 in.) D 2057 mm (81 in.) 2006 mm (79 in.) E 936 mm (36-7/8 in.) 936 mm (36-7/8 in.) F 981 mm (38-19/32 in.) 981 mm (38-5/8 in.) G 1359 mm (53-1/2 in.) 1359 mm (53-1/2 in.) H 2037 mm (80-3/16 in.) 2037 mm (80-3/16 in.) I 721 mm (28-3/8 in.) 721 mm (28-3/8 in.) J 559 mm (22 in.) 559 mm (22 in.
Installation/Operation Supplement 250 Pound Capacity Models with Forward and Two-Way Tilt Option 13° 13° 152 mm (6") Minimum Floor Thickness 2622 mm (103 1/4") 330 mm (13") 475 mm (18") Compacted fill dirt 330 mm (13") 914 mm (36") Recommended 762 mm (30") Allowable CFS219N Figure 7 20 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232148 (EN)
Installation/Operation Supplement Operation V-Computer 1. Turn on main power source (circuit breaker). 5. Load to capacity whenever possible. DO NOT OVERLOAD. Refer to Figure 10. 2. Turn on the ON/OFF switch on the front panel to the ON position. Refer to Figure 9. 3. Push button and turn handle clockwise. Refer to Figure 8. U003IE1A U003IE1A Figure 10 U001IE1B 6. Close door and turn handle counterclockwise until button pops out. Refer to Figure 11. U001IE1B Figure 8 4.
Installation/Operation Supplement 7. Add liquid and/or powder supplies to supply dispenser. Refer to Figure 12. a. Add detergent to container 1. 3 2 b. Add detergent or bleach to container 2. 4 1 c. Add softener to container 3. CYCLE SELECTION NOTE: Liquid supplies may be injected directly into the supply dispenser by an external chemical supply dispenser. Refer to Installation and Programming manuals. 8. Press the START key. Refer to Figure 13.
Installation/Operation Supplement WE-6 Computer NOTE: For models with tilt, refer to “Loading Using Tilt Option” at the end of this section. 1. Turn on main power source (circuit breaker). 2. Use left hand to press and hold the door unlock button on top of the door box cover. Use right hand to turn door handle counterclockwise and open door. Refer to Figure 15. 4. Close door and turn handle clockwise until it locks. 5. Add powder supplies to supply dispenser.
Installation/Operation Supplement Loading Using Tilt Option Forward Tilt Machines Two-Way Tilt Machines 1. Open loading door and secure it to the door latch on the right side of the machine. 2. Turn the selector on the pendant switch left to the REVERSE position. Refer to Figure 18. 1. Open loading door and secure it to the door latch on the right side of the machine. 2. Check that selector on the pendant switch is in the CENTER position.
Installation/Operation Supplement Disposal of Unit This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Refer to Figure 19. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.