Service Homestyle Frontload Washers Refer to Page 6 for Model Numbers www.comlaundry.com Part No.
Table of Contents Section 1 – Safety Information Locating an Authorized Servicer ............................4 Section 2 – Introduction Customer Service ....................................................5 Nameplate Location ................................................5 Model Identification ................................................6 How Your Washer Works .......................................7 Section 3 – Troubleshooting 1. Washer Will Not Start (Door Switch Analysis) . 10 2.
Section 1 Safety Information Throughout this manual and on machine decals, you will find precautionary statements (“CAUTION,” “WARNING,” and “DANGER”) followed by specific instructions. These precautions are intended for the personal safety of the operator, user, servicer and those maintaining the machine. a DANGER Danger indicates the presence of a hazard that will cause severe personal injury, death or substantial property damage if the danger is ignored.
Section 1 Safety Information WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded.
Section 2 Introduction Customer Service If literature or replacement parts are required, contact the source from whom the machine was purchased or contact Alliance Laundry Systems at (920) 748-3950 for the name and address of the nearest authorized parts distributor. For technical assistance, call (920) 748-3121. Nameplate Location When calling or writing about your product, be sure to mention model and serial numbers. Model and serial numbers are located on nameplate(s) as shown.
Section 2 Introduction Model Identification Information in this manual is applicable to these machines: LTS84A*H LTS84B*H LTS85A*H LTS85B*H LTZ85A*H1102 * Add Letter To Designate Color.
Section 2 Introduction How Your Washer Works MOTOR CONTROL BOARD (Located inside control hood) TEMPERATURE SELECTOR SIGNAL SWITCH EXTRA RINSE SWITCH TIMER DISPENSER DRAWER MIXING VALVE INNER BASKET HEATER ELEMENT OUTER TUB FLW1640S WATER PUMP General This frontload washer provides some of the same principles of operation as the typical topload washer.
Section 2 Introduction While water fills the inner basket, a column of air is trapped in a pressure bulb and hose. The air pressure continues to increase as the inner basket fills with water until it is great enough to activate the pressure switch. Then the pressure switch causes the wash fill to stop and starts the reversing rotational washing cycle.
Section 3 Troubleshooting WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 FLOW CHARTS AND SCHEMATICS FOUND ON THE FOLLOWING PAGES ARE FOR MODELS COVERED IN THIS MANUAL.
Section 3 Troubleshooting WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 1.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT N "DOOR LOCKED" LAMP WHT/RED 1 1 2 CR1 L1 DOOR LOCK ACTUATOR WHT TIMER A PNK/BLK MC FU MD BLU/RED TAN PNK MC FU DC COMMON WB WHT/GRY "HEATER ON" LAMP 6 7 10 2 5 4 8 1 3 9 1 H4 (Models equipped with heater) HEATER WHT/ORG THERMOSTAT WB WA RED/YEL WA MC ME WC BRN/WHT VIO ME WC WC MD MB S ORG/BLK GRY/YEL MA A 6 12 EXTRA RINSE 4 5 6 HTR FS3 RL2 N FS2 Door Lock Sense ELECTRONIC CONTROL Lo
Section 3 Troubleshooting WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 2.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT N "DOOR LOCKED" LAMP WHT/RED YEL 1 2 CR1 L1 4 YEL DOOR LOCK ACTUATOR WHT TIMER A BRN/YEL 1 MC FU MD BLU/RED TAN PNK MC FU DC COMMON WB WHT/GRY "HEATER ON" LAMP 6 7 10 2 5 4 8 1 3 9 1 H4 (Models equipped with heater) HEATER WHT/ORG THERMOSTAT WB WA RED/YEL WA MC ME WC BRN/WHT VIO ME WC WC MD MB S ORG/BLK GRY/YEL MB S MA A 6 4 5 6 HTR FS3 RL2 N FS2 Door Lock Sense ELECTRONIC CONTROL
Section 3 Troubleshooting WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 3.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT N "DOOR LOCKED" LAMP WHT/RED YEL 1 2 CR1 L1 4 YEL DOOR LOCK ACTUATOR WHT TIMER A FU MD TAN PNK FU 1 DC COMMON WB WHT/GRY "HEATER ON" LAMP 6 7 10 2 5 4 8 1 3 9 1 H4 (Models equipped with heater) HEATER WHT/ORG THERMOSTAT WB WA RED/YEL WA MC ME WC BRN/WHT VIO ME WC WC BLK/WHT MC BLU/RED MC MD MB S ORG/BLK GRY/YEL MA A 6 4 5 6 HTR FS3 RL2 N FS2 Door Lock Sense ELECTRONIC CONTROL Low
Section 3 Troubleshooting WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 4.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT N "DOOR LOCKED" LAMP WHT/RED YEL 1 2 CR1 L1 4 YEL DOOR LOCK ACTUATOR WHT TIMER A PNK/BLK MC FU MD BLU/RED TAN PNK MC FU DC COMMON WB WHT/GRY "HEATER ON" LAMP 6 7 10 2 5 4 8 1 3 9 1 H4 (Models equipped with heater) HEATER WHT/ORG THERMOSTAT 2 WB WA RED/YEL WA MC ME WC BRN/WHT VIO ME WC WC MD MB S ORG/BLK GRY/YEL MA A START INPUT MB S BLK/WHT BRN/YEL BRN/YEL GRY/BLK 3 5 6 EXTRA RINSE 4
Section 3 Troubleshooting WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 5.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT N "DOOR LOCKED" LAMP WHT/RED YEL 1 2 CR1 L1 4 YEL DOOR LOCK ACTUATOR WHT TIMER A PNK/BLK MB S MC FU MD BLU/RED TAN PNK MC FU MA A ORG/BLK GRY/YEL DC COMMON WB WHT/GRY "HEATER ON" LAMP 6 7 10 2 5 4 8 1 3 9 1 H4 (Models equipped with heater) HEATER WHT/ORG THERMOSTAT WB WA RED/YEL WA MC ME WC BRN/WHT VIO ME WC WC MD 5 6 12 EXTRA RINSE 4 5 6 HTR FS3 RL2 N FS2 Door Lock Sense ELECTRONIC
Section 3 Troubleshooting WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 6.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT N "DOOR LOCKED" LAMP WHT/RED YEL 1 2 CR1 L1 4 YEL WHT TIMER A TIMER SWITCH 5 PNK/BLK MC FU MD BLU/RED TAN PNK MC FU MA A MB S DC COMMON WB WHT/GRY "HEATER ON" LAMP 6 7 10 2 5 4 8 1 3 9 1 H4 (Models equipped with heater) HEATER WHT/ORG THERMOSTAT WB WA RED/YEL WA MC ME WC BRN/WHT VIO ME WC WC MD 5 6 12 EXTRA RINSE 4 5 6 HTR FS3 RL2 N FS2 Door Lock Sense ELECTRONIC CONTROL Low Voltage
Section 3 Troubleshooting WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 7.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT N "DOOR LOCKED" LAMP WHT/RED YEL 1 2 CR1 L1 4 YEL DOOR LOCK ACTUATOR WHT TIMER A PNK/BLK MC FU MD BLU/RED TAN PNK MC FU DC COMMON WB WHT/GRY "HEATER ON" LAMP 6 7 10 2 5 4 8 1 3 9 1 H4 (Models equipped with heater) HEATER WHT/ORG THERMOSTAT WB WA RED/YEL WA MC ME WC BRN/WHT VIO ME WC WC MD MB S ORG/BLK GRY/YEL MA A START INPUT MB S BLK/WHT BRN/YEL BRN/YEL GRY/BLK 3 5 6 12 EXTRA RINSE 4
Section 3 Troubleshooting WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 8.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT N "DOOR LOCKED" LAMP WHT/RED 1 2 CR1 L1 4 YEL DOOR LOCK ACTUATOR WHT TIMER A PNK/BLK MB S MC FU MD BLU/RED TAN PNK MC FU MA A ORG/BLK GRY/YEL DC COMMON WB WHT/GRY "HEATER ON" LAMP 6 7 10 2 5 4 8 1 3 9 1 H4 (Models equipped with heater) HEATER WHT/ORG THERMOSTAT WB WA RED/YEL WA MC ME WC BRN/WHT VIO ME WC WC MD 5 6 4 5 6 HTR FS3 RL2 N FS2 Door Lock Sense PUMP 1 7 2 ELECTRONIC CONTROL
Section 3 Troubleshooting WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 9.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT N "DOOR LOCKED" LAMP WHT/RED YEL 1 2 CR1 L1 4 YEL DOOR LOCK ACTUATOR WHT TIMER A PNK/BLK FU MD TAN PNK FU 2 MC BLU/RED MC DC COMMON WB WHT/GRY "HEATER ON" LAMP 6 7 10 2 5 4 8 1 3 9 1 H4 (Models equipped with heater) HEATER WHT/ORG THERMOSTAT WB WA RED/YEL WA MC ME WC BRN/WHT VIO ME WC WC MD MB S ORG/BLK GRY/YEL MA A START INPUT MB S BLK/WHT BRN/YEL BRN/YEL GRY/BLK 3 5 6 12 EXTRA RI
Section 3 Troubleshooting WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded.
Section 3 Troubleshooting MOTOR DC POWER SUPPLY RL6 FUS1 20 AMP 250 V "DC" Voltage RL4 RL3 RL5 1 D1 2 H2 5 4 3 3 1 2 4 D3 D2 A2 H5 2 1 6 5 7 DL 3 4 6 A1 TG FIELD ROTOR TACH H049SE3A Motor Assembly 800793 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 29
Section 3 Troubleshooting MOTOR DC POWER SUPPLY RL6 FUS1 20 AMP 250 V "DC" Voltage RL4 RL3 RL5 1 D1 2 H2 5 4 3 1 2 D3 D2 3 6 4 A2 5 H5 2 1 7 DL 3 4 6 A1 TG FIELD ROTOR TACH H050SE3A Motor Assembly 30 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800793
Section 3 Troubleshooting MOTOR DC POWER SUPPLY RL6 FUS1 20 AMP 250 V "DC" Voltage RL4 RL3 RL5 1 D1 2 H2 5 4 3 1 2 D3 D2 3 4 A2 6 5 H5 2 1 7 DL 3 4 6 A1 TG FIELD ROTOR TACH H052SE3A Motor Assembly 800793 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 31
Section 4 Grounding WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 10. WALL RECEPTACLE POLARITY CHECK Refer to Figure 1. GROUND NEUTRAL L1 NEUTRAL SIDE 115±12 V.A.C. 0 V.A.C.
Section 4 Grounding WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 12. POWER CORD TO CABINET TOP, CABINET TOP TO CONTROL HOOD REAR PANEL, CONTROL HOOD REAR PANEL TO CONTROL RELAY Refer to Figure 3.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded.
Section 5 Service Procedures TOP COVER LOCKING TABS (Press in on tabs and at same time turn switch 1/4 turn counterclockwise to remove switch.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 e.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 f. Seat horizontal and vertical tabs on front plate of timer completely into slots on control mounting plate. Refer to Figure 8.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 16. TEMPERATURE SWITCH a. Remove three screws holding rear of hood assembly to control hood rear panel. Refer to Figure 5. b.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 20. MOTOR CONTROL BOARD a. Remove three screws holding rear of hood assembly to control hood rear panel. Refer to Figure 5. b.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 23. HEATER INDICATOR LIGHT (Models equipped with heater) a.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 26. ELECTRIC DRAIN PUMP a. While supporting the lower access panel, remove two screws from bottom edge of lower access panel.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 27. FRONT PANEL a. While supporting the lower access panel, remove two screws from bottom edge of lower access panel.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 NOTE: Door seal hose and wire harness must be reinstalled in the appropriate clips and holes along top flange of front panel.
Section 5 Service Procedures STEP 1: Pull seal up. STEP 2: Pull seal out. STEP 3: Pull seal down. STEP 4: Pull seal out and remove.
Section 5 Service Procedures WIRE HARNESS CLIP DOOR SWITCH DOOR SWITCH WIRES DOOR LATCH SWITCH WIRE HARNESS LARGE CLAMP DOOR SEAL DISPENSER HOUSING LARGE CLAMP WHEN INSTALLING DOOR SEAL, ALIGN CONNECTING HOSE IN VERTICAL POSITION FLW1115S Figure 16 800793 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 47
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 28.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 i. When seal releases from lip of front panel, pull out and remove the seal. Refer to Figure 15, Step 4.
Section 5 Service Procedures INLET HOSE MIXING VALVE-TODISPENSER HOSE HOSE CLAMP BACKFLOW PREVENTER HOSE CLAMP SCREWS MIXING VALVE MIXING VALVE PLATE REAR PANEL FLW1641S WIRE HARNESS DISCONNECT BLOCKS MOUNTING CLIP Figure 17 50 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800793
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 31. LOADING DOOR a. Unlatch and open loading door. b. Remove door bezel by prying inside lip up and forward with fingers.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 g. When seal releases from lip of front panel, pull out and remove the seal. Refer to Figure 15, Step 4. h.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 g. Gently pull door lock out through door opening.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 36. HEATING ELEMENT ASSEMBLY (Models equipped with heater) a.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 37. OUTER TUB FRONT PANEL a.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 SCREW OUTER TUB FRONT PANEL WASHERS NUT IMPORTANT: Always replace seal with a new seal.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 38. INNER BASKET PULLEY a. Model LTS85A*H Only: (7) Grasp loading door seal lip. Refer to Figure 15, Step 1.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 (2) Pull down on motor to increase belt tension. Use a Burroughs belt gauge to obtain proper tension.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 39. INNER BASKET ASSEMBLY a. Model LTS85A*H Only: (7) Grasp loading door seal lip. Refer to Figure 15, Step 1.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 (2) Gently lower the access panel to disengage panel locators from bottom edge of front panel. (3) Using the special tool, No.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 j. While supporting the front panel assembly, remove the two bottom front corner screws. Refer to Figure 9. k.
Section 5 Service Procedures WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded.
Section 6 Adjustments WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 IMPORTANT: When reference is made to directions (right or left) in this manual, it is from operator’s position facing front of washer.
Section 6 Adjustments WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 42. LOADING DOOR a. Open loading door. b. Remove door bezel to gain access to nuts. Refer to Figure 25. c.
Section 6 Adjustments WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 43. DOOR CATCH NOTE: When repairing a broken or inoperative No. 685430 Door Catch, proceed as follows: a. Remove door bezel.
Section 6 Adjustments WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the washer before servicing. • Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 44.
Section 7 Wiring Diagrams WARNING Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 WIRING DIAGRAMS AND SCHEMATICS FOUND ON THE FOLLOWING PAGES ARE FOR MODELS COVERED IN THIS MANUAL.
Section 7 Wiring Diagrams WARNING Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage.
Section 7 Wiring Diagrams WARNING Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage.
Section 7 Wiring Diagrams WARNING Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage.
Section 7 Wiring Diagrams WARNING Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage.
