Operation/Maintenance Washer-Extractor Cabinet Hardmount B-Series Microcomputer Variable-Speed HC125BYV and SC125BYV B004C Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) www.comlaundry.com Part No.
Table of Contents Safety Information.............................................................................. Explanation of Safety Messages........................................................... Important Safety Instructions ............................................................... Safety Decals ........................................................................................ Operator Safety.....................................................................................
Safety Information Explanation of Safety Messages Precautionary statements (“DANGER,” “WARNING” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer and those maintaining the machine.
Safety Information 9. Do not install or store the washer where it will be exposed to water and/or weather. 10. Do not tamper with the controls. 11. Do not repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry out. 12.
Safety Information WARNING CAUTION This machine must be installed, adjusted, and serviced by qualified electrical maintenance personnel familiar with the construction and operation of this type of machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment damage, and may void the warranty. SW004 IMPORTANT: Ensure that the recommended clearances for inspection and maintenance are provided.
Safety Information Operator Safety Do not bypass any safety devices in the machine. WARNING WARNING NEVER insert hands or objects into basket until it has completely stopped. Doing so could result in serious injury. SW012 To ensure the safety of machine operators, the following maintenance checks must be performed daily: Never operate the machine with a bypassed or disconnected balance system.
Introduction Introduction Harnessing The “B” electronic control is composed of the electronic control unit and the control fuse board with wiring harness. Only an authorized person should look inside the machine. First TURN OFF POWER, open lid and remove any cover present. The components are described below. Wiring harnesses are modular – harnesses common to various configurations are similar, while those specific to a certain configuration can be added.
Introduction Nameplate Location The nameplate is located at the rear of the machine and inside door. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. 1 B004C 1 Nameplate Figure 1 Replacement Parts If literature or replacement parts are required, contact the source from which the machine was purchased or contact Alliance Laundry Systems at (920) 748-3950 for the name and address of the nearest authorized parts distributor.
Introduction Model Number Familiarization Guide Sample Model Number: *C125BYVQU60001 *C Model Number Prefix 125 Washer-Extractor Capacity (pounds dry weight of laundry) B Type of Electrical Control Y Actuation (Y = Prep for Card Reader) V Washer-Extractor Speed Capability (V = Variable-Speed) Q Electrical Characteristics U6 Design Series 001 Option Identification (varies from machine to machine) * Denotes Brand *C125BYVQU6001 00000000000 200 – 240 7 3 50 - 60 125 N/A 3 3 18 470 N/A 0
Operation Control Panel Figure 3 shows the control panel.
Operation Display Indicators Table 1 lists the various displays and what they mean. The operator should become familiar with these machine displays.
Operation Table 1 (Continued) Display Meaning ___F The first 3 digits are reserved for temperature reading, F indicates “degrees Fahrenheit” FILL “Fill error” – machine did not fill to programmed water level within 10 minutes dOOr “Door” opened during cycle SHUt / door Machine user must “shut door” of the washer to allow the cycle to begin CAnt / OPEn Control cannot unlock the door CArd Control will interpret the coin 2 input as a START signal from a Card Reader with no timing max restriction,
Operation Operating Instructions 5. Close door and turn handle clockwise to horizontal position. Refer to Figure 6. 1. Turn on main power at its source (circuit breaker). 2. Use left hand to press and hold door unlock button located on top left of door lock box. Refer to Figure 4. 3. Turn handle counterclockwise to open. Refer to Figure 4. CHM2014N Figure 6 6. The default wash cycle will display. Refer to Figure 7. NOTE: Perm Press Cold is the default cycle if none is selected.
Operation 8. Add liquid and/or powder supplies to supply dispenser. 9. Insert and remove card. Contact the third party Card Reader manufacturer for details. CHM2015N Figure 8 10. When applicable, add bleach when the ADD BLEACH LED is lit. 11. Press the desired wash cycle keypad. Refer to Figure 7. 12. Press the START keypad. 13. During first fill, the desired wash cycle can be changed. After first fill has ended, the wash cycle active at that moment remains the chosen wash cycle. 14.
Maintenance 3. Check door interlock before starting operation: WARNING Sharp edges can cause personal injury. Wear safety glasses and gloves, use proper tools and provide lighting when handling sheet metal parts. W366R1 IMPORTANT: Replace all panels that are removed to perform service and maintenance procedures. Do not operate the machine with missing guards or with broken or missing parts. Do not bypass any safety devices. Daily a. Attempt to start the machine with the door open.
Maintenance Weekly Monthly 1. Clean the AC drive box filter(s) weekly or more frequently as needed: NOTE: If fan filter service indicator light is on, fan filter must be cleaned immediately to prevent possible damage. Press the thermostat button to reset the indicator light. IMPORTANT: If filter indicator is ignored, repeated resets might shorten life of drive. Clean filter regularly to avoid indicator prompt. a. Open the top cover. b. Grasp the filter handle and pull straight up to remove filter.
Maintenance c. Verify that V-belts are properly tensioned by applying a set force to the belt and measuring the deflection to determine the belt tension. Refer to Table 2 for the acceptable belt tension ranges. Belt tension measurements should be taken as close to the center of the belt span as possible. Refer to Figure 10. 1 2 H039I 1 2 Deflection Span Length Figure 10 Belt Tension Testing Model Belt Belt Span Deflection Range Force Min – Max 125 Motor-Basket 50 in. (1270 mm) .78 in.
Maintenance 1 2 H047I H047I 1 2 Bearing Grease Fitting Seal Grease Fitting Figure 11 3. Lubricate bearings and seals each month OR after every 200 hours of operation. Refer to Figure 11. a. Use a premium-grade lithium-based #2 grease. Never mix two types of grease, such as petroleum and silicone. F232215 b.
Maintenance 4. Remove back panel and check overflow hose and drain hose for leaks. 5. Clean supplied steam filter, where applicable. Refer to Figure 12. 5. Unlock the hinged lid and check the supply dispenser hoses and hose connections. a. Turn off steam supply and allow time for the valve to cool. 6. Clean inlet hose filter screens: b. Unscrew Cap. a. Turn water off and allow valve to cool, if necessary. c. Remove Element and clean. d. Replace Element and Cap. b.
Maintenance Care of Stainless Steel ● Remove dirt and grease with detergent and water. Thoroughly rinse and dry after washing. ● ● ● Avoid contact with dissimilar metals to prevent galvanic corrosion when salty or acidic solutions are present. Remove discoloration or heat tint from overheating by scouring with a powder or by employing special chemical solutions. ● Do not allow salty or acidic solutions to evaporate and dry on stainless steel. Wipe clean of any residues.
