Pocket Hardmount UniLinc and M30 Control Refer to Page 8 for Model Numbers PHM798N PHM798N UniLinc 35 – 125 Models PHM1422C UniLinc 150 Model PHM1422C PHM802N PHM802N M30 35 – 125 Models Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) www.comlaundry.com Part No.
Table of Contents Safety Information............................................................................. Explanation of Safety Messages........................................................... Important Safety Instructions ............................................................... Safety Decals ........................................................................................ Operator Safety.....................................................................................
Safety Information Explanation of Safety Messages Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine. DANGER DANGER indicates the presence of a hazard that will cause severe personal injury, death, or substantial property damage if the danger is ignored.
Safety Information 11. Do not repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry out. 23. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions.
Safety Information WARNING CAUTION This machine must be installed, adjusted, and serviced by qualified electrical maintenance personnel familiar with the construction and operation of this type of machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment damage, and may void the warranty. SW004 IMPORTANT: Ensure that the recommended clearances for inspection and maintenance are provided.
Safety Information Operator Safety Do not bypass any safety devices in the machine. WARNING WARNING NEVER insert hands or objects into basket until it has completely stopped. Doing so could result in serious injury. SW012 To ensure the safety of machine operators, the following maintenance checks must be performed daily: Never operate the machine with a bypassed or disconnected balance system.
Safety Information Safe Operating Environment Safe operation requires an appropriate operating environment for both the operator and the machine. If questions regarding safety arise, contact the manufacturer immediately. Environmental Conditions Ambient Temperature. Water in the machine will freeze at temperatures of 32°F (0°C) or below.
Safety Information Input and Output Services AC Inverter Drive Water Pressure. Best performance will be realized if water is provided at a pressure of 30 – 85 psi (2.0 – 5.7 bar). Although the machine will function properly at lower pressure, increased fill times will occur. Water pressure higher than 100 psi (6.7 bar) may result in damage to machine plumbing. Component failure(s) and personal injury could result. Steam Heat (Optional) Pressure.
Introduction Model Identification Information in this manual is applicable to these models: 8 UW35TV UWL060K1L UWN035K1L UWN100K1M UWU060K1L UW60TV UWL060K1M UWN035K1M UWN100T3V UWU060K1M UW80TV UWL060T3L UWN035T3L UWN125K1M UWU060T3L UW100TV UWL060T3M UWN035T3M UWN125K1V UWU060T3M UW125TV UWL060T3V UWN035T3V UWN125T3V UWU060T3V UW150TV UWL080K1M UWN060K12 UWN150T3V UWU080K1M UWL035K12 UWL080T3V UWN060K1L UWU035K12 UWU080T3V UWL035K1L UWL100K1M UWN060K1M UWU035K1L UW
Introduction This manual is designed as a guide to the installation of the Pocket Hardmount washer-extractor. NOTE: All information, illustrations, and specifications contained in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice. 5. Press the keypad. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. Refer to Figure 1.
Introduction Model Number Familiarization Guide - Models Through 3/31/09 Sample Model Number: UW60TVQU10001 UW Model Number Prefix 60 Washer-Extractor Capacity (60 pounds dry weight of laundry) T Type of Electrical Control T = UniLinc Control V Washer-Extractor Speed Capabilities V = 8 Speeds Q Electrical Characteristics Refer to Table 10.
Specifications and Dimensions . UWTV Models Through 3/31/09 Specifications 35 60 80 100 125 150 Overall width, in (mm) 32.5 (826) 36.625 (930) 41.5 (1054) 41.5 (1054) 48 (1219) 50.25 (1277) Overall height, in (mm) 55.5 (1410) 64.5 (1638) 68.5 (1740) 68.5 (1740) 72 (1829) 79 (2007) Overall depth, in (mm) 43.625 (1108) 45 (1143) 51.5 (1308) 54.
Specifications and Dimensions UWTV Models Through 3/31/09 (Continued) Specifications 35 60 80 100 125 150 Cylinder Speeds / Centrifugal Force Data 1/2 Wash/reverse, rpm (g) 26 (.25) 26 (.31) 26 (.35) 26 (.35) 26 (.40) 23 (.31) Wash/reverse, rpm (g) 42 (.66) 40 (.73) 40 (.82) 40 (.82) 37 (.82) 36 (0.8) Distribution, rpm (g) 83 (2.57) 71 (2.29) 73 (2.57) 70 (2.50) 62 (2.29) 61 (2.
Specifications and Dimensions UWL, UWN and UWU Models Starting 4/1/09 Specifications 35 60 80 100 125 150 Overall Dimensions Overall width, in. (mm) 32.37 (822) 36.07 (916) 41.06 (1043) 41.06 (1043) 47.91 (1217) 50.23 (1256) Overall height, in. (mm) 54.45 (1383) 64.5 (1638) 67.88 (1724) 67.88 (1724) 72.31 (1837) 78.9 (2004) Overall depth, in. (mm) 44.49 (1130) 47.24 (1200) 49.88 (1267) 55.85 (1419) 56.54 (1436) 62.43 (1586) Weight And Shipping Information Net weight, lb.
Specifications and Dimensions UWL, UWN and UWU Models Starting 4/1/09 (Continued) Specifications 35 60 80 100 125 150 Cylinder Speeds / Centrifugal Force Data 1/2 Wash/reverse, rpm (g) (Variable-speed models only) 26 (.25) 26 (.31) 26 (.35) 26 (.35) 26 (.40) 23 (.32) Wash/reverse, rpm (g) 44 (.73) 42 (.66) 40 (0.8) 40 (0.8) 37 (0.8) 36 (0.8) Distribution, rpm (g) (Variable-speed models only) 83 (2.57) 74 (2) 70 (2.50) 70 (2.50) 62 (2.29) 61 (2.
Specifications and Dimensions Machine Dimensions Dimensional Clearances Allow a minimum of 24 inches (60 cm) at the rear and 6 inches (15.24 cm) at the sides for maintenance, inspection, and adjustment. Allow at least 6 inches (15.24 cm) between machines in multiple installations. NOTE: The dimensions shown here are for planning purposes only. They are approximate and subject to normal manufacturing tolerances.
Specifications and Dimensions 3 2 3 4 8 5 1 6 7 F E C G (BASE) D (OVERALL) A (BASE) B (OVERALL) 10 L 11 9 M 12 Q 13 16 K N P O J 15 14 H UW35TV - UW125TV MODELS PHM735N 1 2 3 4 5 6 7 8 External Supply Control Mounting Bracket (Models Through 6/30/08) Door Unlock Button Supply Valve Box Emergency Stop Button Supply Dispenser Door Handle Spray Rinse Nozzle Recirculation Inlet 9 10 11 12 13 14 15 16 Water Inlet Valves Steam Connection (Optional) Shell Vent Power Input (Electric Heat M
Specifications and Dimensions 2 7 3 1 9 4 10 11 5 8 F J 6 C G (BASE) A (BASE) E D (OVERALL) B (OVERALL) L 12 M 10 Q 13 K 11 15 N P O J H 14 TMB736N UW150TV MODELS PHM736N 1 2 3 4 5 6 7 External Supply Control Mounting Bracket (Models Through 6/30/08) Door Unlock Button Emergency Stop Button Supply Valve Box Supply Dispenser Spray Rinse Nozzle Door Handle 8 9 10 11 12 13 14 15 Basket Jog Buttons Recirculation Inlet Shell Vent Water Inlet Valves Steam Connection (Optional) Power
Specifications and Dimensions UW Design 1 and Design 2 Models Starting 4/1/09 Through 10/3/10 (Refer to Figure 5 and Figure 6) Dimension 35 60 80 100 125 150 in. mm in. mm in. mm in. mm in. mm in. mm A 30.125 765 35.625 905 41.125 1045 41.125 1045 48 1219 50 1270 B1 32.37 822 36.07 916 41.06 1043 41.06 1043 47.91 1217 50.23 1276 C 23.48 596 28.07 713 29.46 748 29.46 748 28.5 723 31.41 798 D 44.49 1130 47.24 1200 49.88 1267 55.85 1418 56.
Specifications and Dimensions 3 2 3 4 8 5 1 6 7 E C F (BASE) D (OVERALL) A (BASE) B (OVERALL) K 9 L 10 11 12 P 13 16 J M O N H 15 14 G 35 - 125 MODELS PHM808N PHM808N 1 2 3 4 5 6 7 8 External Supply Control Mounting Bracket (Models Through 6/30/08) Door Unlock Button Supply Valve Box (optional) Emergency Stop Button Supply Dispenser Door Handle Spray Rinse Nozzle (optional) Recirculation Inlet 9 10 11 12 13 14 15 16 Water Inlet Valves Steam Connection (Optional) Shell Vent Power Input
Specifications and Dimensions 2 7 3 1 9 4 10 11 5 8 F J 6 C G (BASE) D (OVERALL) A (BASE) B (OVERALL) E L 12 M 10 Q 13 K 11 15 N P O J H 14 TMB736N 150 MODELS PHM736N 1 2 3 4 5 6 7 External Supply Control Mounting Bracket (Models Through 6/30/08) Door Unlock Button Emergency Stop Button Supply Valve Box Supply Dispenser Spray Rinse Nozzle Door Handle 8 9 10 11 12 13 14 15 Basket Jog Buttons Recirculation Inlet Shell Vent Water Inlet Valves Steam Connection (Optional) Power Input D
Specifications and Dimensions UW Design 3 Models starting 10/4/10 (Refer to Figure 7 and Figure 8) Dimension 35 60 80 100 125 150 in. mm in. mm in. mm in. mm in. mm in. mm A 30.125 765 35.625 905 41.125 1045 41.125 1045 48 1219 50 1270 B 32.37 822 36.07 916 41.06 1043 41.06 1043 47.91 1217 50.23 1276 C 23.41 595 28.07 713 29.29 744 29.29 744 28.5 723 31.41 798 D 45.27 1150 46.81 1189 50 1270 56.03 1423 55.04 1398 62 1575 E 54.
Specifications and Dimensions 1 2 3 3 6 4 4 5 5 E F E C C F (BASE) G (BASE) D (OVERALL) D (OVERALL) A (BASE) A (BASE) B (OVERALL) B (OVERALL) M N L M K L J K N O 8 9 6 7 9 10 10 11 13 14 7 8 O P N O H J 12 13 11 12 G H 35 -- 125 125 MODELS MODELS 35 PHM806N PHM806N 1 2 3 4 5 6 7 Door Unlock Button Emergency Stop Button Supply Dispenser Door Handle Spray Rinse Nozzle (optional) Water Inlet Valves Steam Connection (Optional) 8 9 10 11 12 13 Shell Vent Power Input (Electric Heat Models)
Specifications and Dimensions 1 2 8 3 6 9 4 7 F J 5 C G (BASE) A (BASE) E D (OVERALL) B (OVERALL) N M 9 L 8 K 11 P O 10 O 13 J H 12 PHM807N 150 MODELS PHM807N 1 2 3 4 5 6 7 Door Unlock Button Emergency Stop Button Supply Valve Box Supply Dispenser Spray Rinse Nozzle Door Handle Basket Jog Buttons 8 9 10 11 12 13 Shell Vent Water Inlet Valves Steam Connection (Optional) Power Input Drain Overflow Vent Figure 8 F8138601 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY o
Specifications and Dimensions Machine Foundation Requirements A 6 inch (153 mm) (for 35 and 60 2-speed, L-speed and M-speed models) or a 12 inch (305 mm) (for all other models) thickness of 3500 psi reinforced concrete foundation is absolutely necessary because of the high extract speed and the G-forces exerted. When designing floors or foundations, refer to Table 3 for Floor Load Data for all model sizes.
Specifications and Dimensions Concrete Foundation Pad Installation 6. Wet the hole around the cement foundation well and brush the exposed foundation with cement grout. A concrete foundation and pad may be constructed to elevate the machines. Care must be exercised in the design of the foundation pad due to the force exerted by the machine during extract. This concrete base (recommended not to exceed 8 inches [20.
Specifications and Dimensions Brush with Cement Grout Brush with Cement Grout 5 1 3 3 Brush with Cement Grout LENGTH FOR ONE MACHINE 3 3 4 2 6 COMPACTED FILL DIRT 18 in. (457 mm) DEPTH COMPACTED FILL DIRT 18 in. (457 mm) DEPTH PHM790N Figure 9 35 1 60 2-Speed, L-Speed and M-Speed 6 in. (153 mm) Variable-Speed 12 in. (305 mm) 26 80 100 125 150 12 in. (305 mm) 12 in. (305 mm) 12 in. (305 mm) 12 in. (305 mm) 2 6 in. (152 mm) minimum 6 in. (152 mm) minimum 6 in.
Specifications and Dimensions Floor Load Data Static and dynamic loads on the floor or foundation are shown in Table 4 and Table 5. UWTV Pocket Hardmount Floor Load Data (Models Through 3/31/09) Specifications Design Series 35 60 80 Static floor load, lbs (kN) U1 and greater 1272 (5.66) 1677 (7.45) 2292 (10.2) Static pressure, lbs/ft2 U1 and greater 169 (8.08) 187 (8.94) 184 (8.79) 100 125 150 2490 (11.1) 3283 (14.6) 3936 (17.5) 199 (9.6) 205 (9.8) 202 (9.
Specifications and Dimensions UWL, UWN AND UWU Pocket Hardmount Floor Load Data (Models Starting 4/1/09) Specifications Static floor load, lbs. (kN) Static pressure, lbs/ft2 (kN/m2) Dynamic floor load, lbs. (kN) Dynamic pressure, lbs/ft2 (kN/m2) Dynamic load frequency, Hz Design Series Speed 35 60 80 100 125 150 U1 and greater Variable-speed 1272 (5.66) 1442 (6.42) 2292 (10.2) 2490 (11.1) 3283 (14.6) 3936 (17.5) 2-speed 1272 (5.66) 1442 (6.42) N/A N/A N/A N/A L-speed 1272 (5.
Specifications and Dimensions Table 5 (continued) UWL, UWN AND UWU Pocket Hardmount Floor Load Data (Models Starting 4/1/09) Specifications 1Maximum vertical load, lbs. (kN) Base moment, lb/ft (kN/m) Design Series Speed 35 60 80 100 125 150 U1 and greater Variable-speed 2848 (12.7) 4146 (18.4) 5895 (26.2) 6994 (31.1) 7028 (31.3) 8437 (37.52) 2-speed 1745 (7.8) 2392 (.41) N/A N/A N/A N/A L-speed 1797 (8) 2342 (10.4) N/A N/A N/A N/A M-speed 2216 (9.9) 3066 (13.6) 4459 (19.
Specifications and Dimensions Mounting Bolt Installation Requirements For new foundations a bolt-locator fixture or rebar frame is available and a preferred option. This rigid welded assembly made of reinforcing rod and mounting bolts is designed to be embedded in concrete. Refer to Figure 11.
Specifications and Dimensions Machine Mounting and Grouting After the concrete has cured, proceed as follows: 1. Place the washer-extractor adjacent to the foundation. Do not attempt to move the machine by pushing on the sides. Always insert a pry bar or other device under the bottom frame of the machine to move it. 2. Remove the wood skid by unscrewing the carriage bolts holding the skid to the bottom frame of the washer-extractor. 3. Place the washer-extractor carefully over the anchor bolts.
Specifications and Dimensions Mounting Bolt Hole Locations 28.625 in. (727 mm) 0.75 in. (19 mm) A 30.1875 in. (767 mm) 36 in. (914 mm) A 43.28 in. (1089 mm) 21.1875 in. (538 mm) 34.5 in. (876 mm) 40.1875 in. (1022 mm) 34.16 in. (868 mm) 26.125 in. (664 mm) 2 in. (51 mm) 2 in. (51 mm) 30.125 in. (765 mm) 35 MODEL FRONT OF MACHINE PHM630N Figure 12 NOTE: Mounting holes marked “A” are on V-speed Models only.
Specifications and Dimensions 0.75 in. (19 mm) 0.75 in. (19 mm) 34.125 in. (867 mm) 4.8125 in. (122 mm) 39.25 in. (997 mm) 1.25 in. (32 mm) 36 in. (914 mm) 9 in. (229 mm) 44.8125 in. (1138 mm) 10.75 in. (273 mm) 1.25 in. (32 mm) 34.5625 in. (878 mm) 10.6875 in. (271 mm) 2 in. (51 mm) 31.625 in. (803 mm) 2 in. (51 mm) 0.75 in. (19 mm) 35.625 in.
Specifications and Dimensions 0.75 in. (19 mm) 0.75 in. (19 mm) 39.625 in. (1008 mm) 6.75 in. (171 mm) 43.75 in. (1111 mm) 9 in. (229 mm) 2.25 in. (57 mm) 52.1875 in. (1326 mm) 13.625 in. (346 mm) 46.3125 in. (1176 mm) 2.25 in. (57 mm) 39.75 in. (1010 mm) 13.625 in. (346 mm) 35.125 in. (892 mm) 3 in. (76 mm) 3 in. (76 mm) 41.125 in. (1045 mm) 0.75 in.
Specifications and Dimensions 0.75 in. (19 mm) 0.75 in. (19 mm) 46.5 in. (1181 mm) 7 in. (178 mm) 10 in. (254 mm) 48 in. (1219 mm) 61.5 in. (1562 mm) 15 in. (381 mm) 55.47 in. (1409 mm) 48.94 in. (1243 mm) 15.25 in. (387 mm) 23.25 in. (591 mm) 23.25 in. (591 mm) 48 in. (1219 mm) 0.75 in.
Specifications and Dimensions 56 in. (1422 mm) 10.375 in. (264 mm) 48.125 in. (1223 mm) 51.375 in. (1305 mm) 47.875 in. (1216 mm) 10.375 in. (264 mm) 57.4 in. (1457 mm) 12.125 in. (308 mm) 67.1 in. (1704 mm) 15 in. (381 mm) 4 in. (102 mm) 1.5 in. (38.1 mm) 1.5 in. (38.1 mm) 47 in. (1193 mm) 50 in.
Specifications and Dimensions Grout Placement 30.125 in. (765 mm) 17.88 in. (454 mm) 36 in. (914 mm) 27.875 in. (708.025 mm) 36 in. (914.4 mm) 20 in. (508 mm) 4.0625 in. (103 mm) typical 22 in. (559 mm) 4.0625 in. (103 mm) typical 4.0625 in. (103 mm) typical 30.13 in. 35.625 in.(765 mm) (905 mm) 35 VARIABLE-SPEED MODEL 35 2-SPEED MODEL PHM547N PHM547N PHM574N PHM574N 35.63 in. (905 mm) 35.625 in. (905 mm) 11.9375 in. (303 mm) 4.0625 in. (103 mm) typical 35.9375 in. (913 mm) 12 in. 27.5 in.
Specifications and Dimensions Gap Setting for Vibration Switch After the machine has been properly installed, the vibration switch gap must be verified. To locate the vibration switch refer to Figures 18, 19 and 20. For UniLinc models, while the control is displaying the Inputs Outputs Menu the alarm will sound when the frame switch is activated. To verify and set the vibration switch gap use the following procedures: WARNING Verify Vibration Switch Gap (for 35-125 Pound Models): 1. Insert 0.
Specifications and Dimensions 35 Pound Model ADJUSTMENT BOLT VIBRATION SWITCH PHM794N PHM794N Figure 18 F8138601 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 39
Specifications and Dimensions 60, 80, 100 and 125 Pound Models VIBRATION SWITCH ADJUSTMENT BOLT PHM795N PHM795N Figure 19 40 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8138601
Specifications and Dimensions Design 1 150 Pound Model VIBRATION SWITCH PHM716N PHM716N Figure 20 F8138601 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 41
Specifications and Dimensions Drain Connection Requirements DRAIN TROUGH CONFIGURATION A drain system of adequate capacity is essential to washer-extractor performance. The water can empty directly into a sump or floor drain. Figure 21 shows the drain line configuration and Figure 22 shows the drain trough configuration.
Specifications and Dimensions IMPORTANT: Do not block the overflow vent above the drain line. If water or suds flow from the overflow vent and the machine has been verified to be operating properly with proper water levels and correct amount of laundry chemicals, a drain line may be added to the vent and routed to a drain trough. 1. Remove the riveted bracket on the rear panel for access to the overflow vent pipe. 2. Route a drain pipe from the vent pipe to a drain trough.
Specifications and Dimensions Water Connection WARNING To prevent personal injury, avoid contact with inlet water temperatures higher than 125° Fahrenheit (51° Celsius) and hot surfaces. W748 Maximum water inlet temperature is 190° Fahrenheit (88° Celsius). Water Supply Information Specifications 35 60 80/100 125/150 2 2 2 2 Main fill water inlet size, in. (mm) 3/4 (19) 3/4 (19) 3/4 (19) 1 (25.4) Number of Spray Rinse water inlets 2 2 2 2 Spray rinse water inlet size, in.
Specifications and Dimensions To connect water service to machine with rubber hoses, use the following procedure: Water Supply Line Sizing Model 1. Before installing hoses, flush the water system for at least two minutes. Number of Machines Supply Line Size, in. (mm) Main Hot/Cold 1 1 (25) 0.75 (19) 2 1.5 (38) 1 (25) 3 2 (50) 1.25 (32) 4 2 (50) 1.5 (38) 1 1.25 (32) 1 (25) 2 2 (50) 1.25 (32) 3 2 (50) 1.5 (38) 4 2.5 (64) 2 (50) 1 1.25 (32) 1 (25) 2 2 (50) 1.
Specifications and Dimensions Electrical Installation Requirements IMPORTANT: Electrical ratings are subject to change. Refer to serial decal for electrical ratings information specific to your machine. WARNING This machine must be installed, adjusted, and serviced by qualified electrical maintenance personnel familiar with the construction and operation of this type of machinery. They must also be familiar with the potential hazards involved.
Specifications and Dimensions On variable-speed models, the AC drive provides thermal overload protection for the drive motor. However, a separate three-phase circuit breaker must be installed for complete electrical overload protection. This prevents damage to the motor by disconnecting all legs if one should be lost accidentally. Check the serial plate on the back of the washer-extractor for recommended circuit breaker requirements size.
Specifications and Dimensions Machines can be converted for lower voltage operation and/or 50 Hz operation. Refer to conversion label by serial plate for details. After electrical installation is complete, run the machine through a test cycle and check for a clockwise basket rotation during the extract step. If rotation is not clockwise, disconnect the power from the machine and have a qualified electrician reverse any 2 motor leads.
Specifications and Dimensions Table 5 (continued) Voltage Designation Electric Heat Machines *mm2 *AWG Breaker Full Load Amps *mm2 *AWG Breaker Full Load Amps Wire Phase Cycle Voltage Code Model X 200 – 240 50/60 1/3 2/3 12/8 15/15 14/14 2.5/2.5 NOT AVAILABLE X 200 – 240 50/60 1/3 2/3 15/8 20/15 12/14 4/2.5 NOT AVAILABLE Q 200 – 240 50/60 3 3 8 15 14 2.5 42 50 6 16 O** 208 – 240 60 3 3 7 20 12 4 38 50 6 16 R 380 – 480 50/60 3 3 6 15 14 2.
Specifications and Dimensions Voltage Designation Electric Heat Machines *mm2 *AWG Breaker Full Load Amps *mm2 *AWG Breaker Full Load Amps Wire Phase Cycle Voltage Code Model Q 200 – 240 50/60 3 3 10 15 14 2.5 108 110 1 50 Q 200 – 240 50/60 3 3 14 20 14 2.5 108 110 1 50 R 380 – 480 50/60 3 3 10 15 14 2.5 40 50 6 16 N 440 – 480 50/60 3 3 10 15 14 2.5 40 50 6 16 380 – 415 50/60 3 3 10 15 14 2.
Specifications and Dimensions Steam Requirements (Steam Heat Option Only) For washer-extractors equipped with optional steam heat, install piping in accordance with approved commercial steam practices. Steam requirements are shown in Table 11. WARNING NOTE: Failure to install the supplied steam filter may void the warranty. Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns.
Specifications and Dimensions Chemical Injection Supply System Undiluted chemical dripping can damage the washerextractor. Therefore, all chemical supply dispenser pumps should be mounted below the washer’s injection point. All dispenser tubing should also run below the injection point. Loops do not prevent drips if these instructions are not followed. Failure to follow these instructions could damage the machine and void the warranty. Figure 27 shows a typical Chemical Injection Supply System.
Specifications and Dimensions Connecting External Liquid Supplies to the Washer-Extractor 1 1. Remove knockout from supply dispenser. Refer to Figure 28. Plugs are assembled inside the tubing ring. 2 3 2. Install PG connector in hole with strain reliefs, included in the seal nut. 4 5 3. Insert tubes through PG base. Do not remove cups. Tube should extend into the plastic cup, with the exception of the softener tube, which should be routed to the outside of the cup. 6 4.
Specifications and Dimensions 1 2 3 4 5 6 PHM553N PHM553N 1 2 3 Strain Relief for Liquid Chemical Supply Lines Supply Dispenser Lid Nozzles 4 5 6 Dry Supply Cups Dry Supply Insert Polypropylene Supply Dispenser IMPORTANT: Do not attach anything to nozzles. Air gap must be maintained.
Specifications and Dimensions External Supplies For proper communication between the washerextractor and an external chemical supply system, it is important for the signal power to be connected properly. The included wiring diagram (F8133502) shows several different options for safe and correct wiring of this interface.
Specifications and Dimensions Chemical Injection Using Internal 24VAC Control Transformer Terminal “24VAC COM” is used to connect one side of the internal control transformer to the external dispenser input signals common. NOTE: Using the Internal 24VAC 300 Milliamp Control Transformer is recommended by Alliance Laundry Systems.
Specifications and Dimensions Chemical injection Using External AC Power Source IMPORTANT: The external power must supply power of 240VAC or less and be protected at 3 Amps or less. NOTE: An External AC Power Source is NOT provided by Alliance Laundry Systems. 1. Remove the red jumper wire installed by the factory between “24VAC”: and “RELAY COM”. NOTE: Power for external supplies must not be derived from the high-voltage main power connection point. 2.
Specifications and Dimensions External Supply Signals Wash-cycle signals are provided to the external chemical supply equipment and a “wait for the next step” signal can be received from the supply equipment. For example, if ES1 is selected the K1 contact will close and power will be supplied to Supply 1 Signal. The contact will remain closed for the amount of time programmed in control. Refer to Figure 33 for Internal Supply Connection or Figure 34 for External AC Connection.
Specifications and Dimensions 3 = Neutral = Power 1 2 PHM824N 1 ES1 Power supply 2 K1 Contact 3 Supply 1 Signal Figure 34 F8138601 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 59
