A5 Quick Install Guide Cover AR400 Series Router Quick Install Guide Safety Information and Installation Instructions AR410 AR410S AR440S AR441S AR450S C613-04058-00 Rev A
AR400 Series Router AR400 Series Quick Install Guide Document Number C613-04058-00 REV B. Copyright © 2005 Allied Telesyn International, Corp. 19800 North Creek Parkway, Suite 200, Bothell, WA 98011, USA. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn. Allied Telesyn International, Corp. reserves the right to make changes in specifications and other information contained in this document without prior written notice.
Quick Install Guide 3 Table of Contents Electrical Safety Statements ............................................................................................ 4 Models Covered By This Guide .................................................................................... 5 Package Contents ............................................................................................................. 5 Selecting a Site ....................................................................................
AR400 Series Router Electrical Safety Statements Electrical Safety IMPORTANT: This equipment must be installed in accordance with safety precautions (Safety, page 23). Elektrische Sicherheit WICHTIG: Für die Installation dieses Gerätes ist die Einhaltung von Sicherheitsvorkehrungen erforderlich (Sicherheit, Seite 24). Elektrisk sikkerhed VIGTIGT: Dette udstyr skal installeres i overensstemmelse med sikkerhedsadvarslerne (Sikkerhed, side 25).
Quick Install Guide 5 Models Covered By This Guide This Quick Install Guide includes information on these models: ■ AR410 ■ AR410S ■ AR440S ■ AR441S ■ AR450S Package Contents Item included for each router AR410 AR410S AR440S AR441S AR450S One AR400 Series router ✔ ✔ ✔ One AC power cord ✔ ✔ ✔ One power cord retaining clip ✔ ✔ ✔ One serial cable for connecting the router to a terminal or PC ✔ ✔ ✔ ✔ ✔ One serial null modem cable for connecting the router to a terminal or PC Two
AR400 Series Router Selecting a Site AR410, AR410S, AR450S You can install the router on a level surface such as a desktop or bench, or in a standard 19-inch rack, using the rack-mount kit supplied with the router. AR440S, AR441S The router can be installed on a level surface such as a desktop or bench, in a standard 19-inch rack, or on a firm wall. When you install the router, choose a site that: ■ allows adequate airflow around the router and its vents. ■ is free of dust and moisture.
Quick Install Guide 7 Installing the Router Warning This equipment must be earthed. Prepare to install the router 1. Read the safety information Read the safety information included in this Quick Install Guide. This Quick Install Guide is also on the Documentation and Tools CD-ROM and you can download a copy from http:// www.alliedtelesyn.co.nz/support/ar400/. 2. Unpack the router. Verify the package contents. If any items are damaged or missing, contact your sales representative. 3.
AR400 Series Router 6. Apply power to the router. Fit the power cord retaining clip to the AC power inlet on the router’s rear panel. Connect the provided power cord to the AC power inlet and clip it in place. Switch the router’s power switch to the ON position. The Power LED lights continuously and the System LED lights briefly. The Port LEDs also light briefly. If the LEDs fail to light, the most likely cause is that the router is not receiving power.
Quick Install Guide 9 Configuring the Router AR400 Series routers can be configured via the Command Line Interface (CLI) or Graphical User Interface (GUI). AR410, AR410S, AR450S You must first use the CLI to assign an IP address to the router (“Using the CLI to configure a router” on page 9). You may then use the CLI or the GUI (“Using the GUI to configure the router” on page 10) to complete the configuration.
AR400 Series Router 2. Log in and set the password. The log in prompt appears on the terminal or PC. If the log in prompt does not appear, press [Enter] two or three times. When the router boots for the first time it automatically creates an account with manager privileges. The account has the log in name “manager” and the password is “friend”. Passwords are case sensitive. At the log in prompt, enter the log in name and password.
Quick Install Guide 11 Configure the AR410, AR410S or AR450S using the GUI 1. Connect the PC to a router switch port. The PC can be connected directly, or through your LAN. To connect the PC directly to the router, use a straight-through Ethernet cable to connect an Ethernet card on the PC to any one of the router’s switch ports. Note the PC’s IP address and mask.
AR400 Series Router 4. Assign an IP address to VLAN1. Assign the VLAN1 interface an IP address in the subnet that the PC uses, using the command: add ip interface=vlan1 ip=ipaddress mask=mask 5. Browse to the GUI. If you access the Internet through a proxy server, set your browser to bypass the proxy for the IP address you assigned to the VLAN1 interface. Point your web browser at the IP address of the VLAN interface. 6. Log in and set the password.
Quick Install Guide 13 Configure the AR440S or AR441S using the GUI Caution Only one DHCP server should usually be enabled on a network. If you have an existing DHCP server, we recommend disabling either it or the DHCP server configured by default on the router. If another device on your network already uses the router’s default IP address, 192.168.1.1, do not connect the router to the network until you have changed the management port’s address by using the command line. 1.
AR400 Series Router 2. Assign the PC an IP address in the same subnet as the router. The router’s default IP address is 192.168.1.1. 3. Browse to the GUI. If you access the Internet through a proxy server, set your browser to bypass the proxy for 192.168.1.1. Point your web browser at 192.168.1.1. 4. Log in and set the password. At the log in prompt, enter the log in name and password. Passwords are case sensitive.
Quick Install Guide 15 AR440S and AR441S Default Configuration The default configuration file boot.cfg loads automatically when the router starts up. This file is stored in the router’s flash memory. Figure 1: Default configuration file for AR440S and AR441S routers #Default configuration file boot.cfg # Set the command help file. You may have a more recent help # file. set help=54-266A.HLP # Enable IP and assign an IP address to the default VLAN. enable ip add ip interface=vlan1 ip=192.168.1.
AR400 Series Router Connecting the Data Cables Connecting the router to your network: 1. Connect to the LAN If you have not already done so, use straight-through Ethernet patch cables to connect the device(s) on your private network (LAN) to the router’s switch port(s). By default, all switch ports are members of VLAN1. 2. Connect to the DMZ port AR440S, AR441S: If you have public servers to connect, connect them to switch ports in a different VLAN.
Quick Install Guide 17 System LEDs LEDs indicate the router’s operational status and port activity.. AR410, AR410S, AR450S LEDs LED State Function Power Green The router is receiving power and the power switch is ON. System Red or Amber Lit briefly during router start up, or the router is malfunctioning. Flashing The fan has failed. Off Normal operation. Green A port interface card (PIC) is correctly installed and has been detected by the router.
AR400 Series Router AR440S, AR441S LEDs LED State Function Power Green The router is receiving power and the power switch is ON. System Red or amber Lit briefly during router start up, or the router is malfunctioning. Flashing The fan has failed. Off Normal operation. Green A port interface card (PIC) is correctly installed and has been detected by the router. Off No PIC is installed, or the router has not recognised the PIC. 1-5 Green A 100 Mbps link has been established.
Quick Install Guide 19 Documentation and Tools CD-ROM The Documentation and Tools CD-ROM bundled with each router contains the complete Document Set for your router. The CD-ROM also includes tools for managing your router. The Document Set on the CD-ROM includes: ■ This Quick Install Guide. ■ The AR400 Series User Guide, which provides an introduction to the router and its operational features and characteristics.
AR400 Series Router Emission Compliance Statements STANDARDS: The AR410 and AR410S meet the following standards: Category Approval Agency and Requirement Safety UL60950 EN60950 AS/NZS 3260, ACA TS001 Electromagnetic Compliance FCC CFR47 Part 15 Class A EN55022 Class A VCCI Class A AS/NZS CISPR22 Class A Immunity EN55024 Network Interface (where applicable) ISDN Limited Network Protocol Analysis FCC Part 68, Subpart D IC CS-03, Issue 8, Part I and IV TBR3 TBR4 U.S.
Quick Install Guide 21 STANDARDS: The AR440S and AR441S meet the following standards: Category Approval Agency and Requirement Safety UL60950-1 EN60950-1 AS/NZS 60950 Electromagnetic Compliance FCC CFR47 Part 15 Class A EN55022 Class A VCCI Class A AS/NZS CISPR22 Class A Immunity EN55024 Network Interface (where applicable) ISDN Limited Network Protocol Analysis FCC Part 68, Subpart D IC CS-03, Issue 8, Part I and IV TBR3 TBR4 TR048 TIA-968-A PTC 270 G.992.1 Annex A (AR440S only) G.992.
AR400 Series Router STANDARDS: The AR450S meets the following standards: Category Approval Agency and Requirement Safety UL60950 EN60950 AS/NZS 3260 Electromagnetic Compliance FCC CFR47 Part 15 Class B EN55022 Class B VCCI Class B AS/NZS CISPR22 Class B Immunity EN55024 U.S. Federal Communications Commission RADIATED ENERGY Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Quick Install Guide 23 Safety WARNING: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. ELECTRICAL NOTICES WARNING: ELECTRIC SHOCK HAZARD To prevent ELECTRIC shock , do not remove the cover. No user-serviceable parts inside. This unit contains HAZARDOUS VOLTAGES and should only be opened by a trained and qualified technician. LIGHTNING DANGER DANGER: DO NOT WORK on equipment or CABLES during periods of LIGHTNING ACTIVITY.
AR400 Series Router Sicherheit WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen ergreifen. ACHTUNG: GEFÄHRLICHE SPANNUNG Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren Teile. Das Gerät steht unter Hochspannung und darf nur von qualifiziertem technischem Personal geöffnet werden.
Quick Install Guide 25 Sikkerhed ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. ELEKTRISKE FORHOLDSREGLER ADVARSEL: RISIKO FOR ELEKTRISK STØD For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre dele, der kan repareres af brugeren. Denne enhed indeholder LIVSFARLIGE STRØMSPÆNDINGER og bør kun åbnes af en uddannet og kvalificeret tekniker.
AR400 Series Router Veiligheid WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen. WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT WAARSCHUWING: GEVAAR VOOR ELEKTRISCHE SCHOKKEN Verwijder het deksel niet, teneinde ELEKTRISCHE schokken te voorkomen. Binnenin bevinden zich geen onderdelen die door de gebruiker onderhouden kunnen worden.
Quick Install Guide 27 Sécurité MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. INFORMATION SUR LES RISQUES ÉLECTRIQUES AVERTISSEMENT: DANGER D’ÉLECTROCUTION Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement protecteur du matériel. Ce matériel ne contient aucun élément réparable par l’utilisateur.
AR400 Series Router Turvallisuus VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin. SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA VAROITUS: SÄHKÖISKUVAARA Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa olevia osia. Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain koulutettu ja pätevä teknikko.
Quick Install Guide 29 Norme di Sicurezza AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti. AVVERTENZE ELETTRICHE ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le componenti interne non sono riparabili dall’utente. Questa unità ha TENSIONI PERICOLOSE e va aperta solamente da un tecnico specializzato e qualificato.
AR400 Series Router Sikkerhet ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. ELEKTRISITET ADVARSEL: FARE FOR ELEKTRISK SJOKK For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som brukeren kan reparere på innsiden. Denne enheten inneholder FARLIGE SPENNINGER, og må kun åpnes av en faglig kvalifisert tekniker.
Quick Install Guide 31 Segurança AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas. AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS ATENÇÃO: PERIGO DE CHOQUE ELÉTRICO Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças que possam ser consertadas pelo usuário. Este aparelho contém VOLTAGENS PERIGOSAS e só deve ser aberto por um técnico qualificado e treinado.
AR400 Series Router Seguridad ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto. AVISOS ELECTRICOS ADVERTENCIA: PELIGRO DE ELECTROCHOQUE Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún componente en el interior al cual puede prestar servicio el usuario. Esta unidad contiene VOLTAJES PELIGROSOS y sólo deberá abrirla un técnico entrenado y calificado.
Quick Install Guide 33 Säkerhet VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK: RISK FÖR ELEKTRISK STÖTFör att undvika ELEKTRISK stöt, ta ej av locket. Det finns inga delar inuti som behöver underhållas. Denna apparat är under HÖGSPÄNNING och får endast öppnas av en utbildad kvalificerad tekniker.
AR400 Series Router Connection to mains voltage supply This product is supplied with a power cord that incorporates a moulded plug and has been approved for use. It must only be used with the power cord supplied. For continued protection against the risk of fire and shock hazard, replace fuses only with the same type and rating. Telecommunications Interfaces Warning To reduce risk of fire use only No.26 awg or larger telecommunications line cord if the cord supplied is not used with the apparatus.
Quick Install Guide 35 Connection to ISDN network This product is supplied with an approved patch cord for connection to the ISDN Basic Rate Network. Ports for the connection of other apparatus The following interfaces normally operate at SELV (Safe Extra Low Voltage) levels: ■ Asynchronous (console) ports ■ Ethernet ports ■ G703 ports ■ Synchronous ports Note SELV is a secondary circuit whose voltages do not exceed a safe value under normal operating conditions and under single fault conditions.
AR400 Series Router US Federal Communications Commission (FCC) This equipment complies with Part 68 of the Federal Communications Commission (FCC) rules for the United States. A label is located on the underside of the base unit containing the FCC registration number. You must, upon request, provide the following information to your local telephone company: For the AR021U PIC Facility Interface Code 021S5 Service Order Code 6.
Quick Install Guide 37 Canadian Department of Communications The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
AR400 Series Router EC Declaration of Conformity We: ALLIED TELESYN RESEARCH LIMITED 27 NAZARETH AVENUE CHRISTCHURCH 8002 NEW ZEALAND Declare under our sole legal responsibility that the following product meets the safety, protection and conformity requirements of council directives 1999/5/EC, 89/336/EEC and 73/23/EEC (as amended by directive 93/68/EEC) on the approximation of the laws of member states relating to electromagnetic compatibility, electrical safety and the mutual recognition of conformi
