User guide
Table Of Contents
- installation guide
- Electrical Safety and Installation Requirements fo...
- STANDARDS: This product meets the following standa...
- RADIATED ENERGY
- Note: This equipment has been tested and found to ...
- Note: Modifications or changes not expressly appro...
- This Class A digital apparatus meets all requireme...
- Cet appareil numérique de la classe A respecte tou...
- RFI Emission EN55022 Class A
- Immunity EN50082-1
- WICHTIG: Für den Betrieb dieses Gerätes ist die Ei...
- VIGTIGT: Dette udstyr skal bruges i overensstemmel...
- BELANGRIJK: Dit apparaat moet in overeenstemming m...
- IMPORTANT : Cet équipement doit être utilisé confo...
- TÄRKEÄÄ: Tätä laitetta on käytettävä turvaohjeiden...
- IMPORTANTE: questa apparecchiatura deve essere uti...
- VIKTIG: Dette utstyret skal brukes i samsvar med s...
- IMPORTANTE: Este equipamento tem que ser operado s...
- IMPORTANTE: La operación de este equipo debe lleva...
- OBS! Alla nödvändiga försiktighetsåtgärder måste v...
- Electrical Safety and Installation Requirements fo...
- STANDARDS: This product meets the following standa...
- Manufacturers Name: Allied Teleysn International, ...
- Manufacturers Telephone: 408-730-0950 Declares tha...
- Complies with FCC Part 15B, Class B Limits:
- This device complies with part 15 of the FCC Rules...
- This equipment has been tested and found to comply...
- - Reorient or relocate the receiving antenna.
- - Increase the separation between the equipment an...
- - Connect the equipment into an outlet on a circui...
- - Consult the dealer or an experienced radio/TV te...
- Changes and modifications not expressly approved b...
- This Class B digital apparatus meets all requireme...
- Cet appareil numérique de la classe B respecte tou...
- RFI Emission EN55022 Class B
- Immunity EN50082-1
- WICHTIG: Für den Betrieb dieses Gerätes ist die Ei...
- VIGTIGT: Dette udstyr skal bruges i overensstemmel...
- BELANGRIJK: Dit apparaat moet in overeenstemming m...
- IMPORTANT : Cet équipement doit être utilisé confo...
- TÄRKEÄÄ: Tätä laitetta on käytettävä turvaohjeiden...
- IMPORTANTE: questa apparecchiatura deve essere uti...
- VIKTIG: Dette utstyret skal brukes i samsvar med s...
- IMPORTANTE: Este equipamento tem que ser operado s...
- IMPORTANTE: La operación de este equipo debe lleva...
- OBS! Alla nödvändiga försiktighetsåtgärder måste v...
- Table of Contents
- Preface
- AT-3714F, AT-3726 Hardware Description
- Installing the Switch
- Verifying Switch Package Contents
- Safety Information
- Preparing the Site
- Rack Mounting the Unit
- Media Dependent Adapters
- Figure23 AT-3701 and AT-3701F/SC MDA Front Pan...
- Verifying Package Contents
- Media Dependent Adapter Features
- Table23 Media Dependent Adapter Features
- Installing a Media Dependent Adapter
- 1. Disconnect the switch’s power cord.
- 2. Unscrew the three Phillips head screws on the b...
- 3. The standoff on the MDA serves as a guide to sl...
- 4. Slide the MDA into its empty slot making sure t...
- 5. Attach the female 50-pin female connector to it...
- Figure24 Guiding the MDA (AT-3701) Standoff in...
- Figure25 Connecting the 50-Pin Female Connecto...
- MDA LEDs
- Installing a Media Dependent Adapter
- Table24 Media Dependent Adapter LEDs
- Troubleshooting
- Switch Configurations
- AppendixA
- AppendixB

Index-1
Index
Numerics
100Base-FX port 1-1
100Base-TX port 1-1
A
Activity LED 2-6
AT-3701 MDA 1-5, 2-9
AT-3701F/SC MDA 1-5, 2-9
auto-negotiation 1-2
B
bandwidth capability 1-1, 1-2
C
clear-channel architecture 1-2
conventions, document Preface-ii
D
DB9 straight-through cable 2-7
diagnostics 3-5
disabled port 3-4
E
External Address Lookup Engine 1-3
F
FLT LED 2-6
fragment-free cut-through modes 1-2
L
LEDs 2-6, 3-3
Link OK LED 2-6
M
MDA LEDs 2-11
mirror port 1-4
MS-Windows VTERM 1-5
O
Omega 1-3, 3-1, 3-4, 3-5
out-of-band management 1-5
P
PWR LED 2-6
R
redundant backbone connections 1-3
reset button 1-5, 3-1, 3-5
RS232 connector 1-5, 2-7, 3-5
S
shared memory architecture 1-2
SNMP 3-5
SNMP Management Information Base 1-3
SNMP trap message 3-3
Spanning Tree Protocol 1-3
standalone switch 4-1
store-and-forward mode 1-2
switch default settings 2-8
T
TCP/IP 3-3
Telnet 3-5
terminal settings 2-7
W
Worst Case Path Delay Value 3-2