AT-A15/SX AT-A15/LX AT-A16 AT-A17 AT-A18 AT-A19 Expansion Modules Quick Install Guide PN 613-10814-00 Rev B
Copyright 1999 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA 94086, USA All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn International, Corp.
Safety Warnings Standards: This product meets the following standards U.S. Federal Communications Commission RADIATED ENERGY Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table of Contents Safety Warnings ................................................................................................................... iii Overview .................................................................................................................................1 Verifying the Package Contents .............................................................................................3 Reviewing Safety Precautions ..............................................................
Overview The AT-A1x Series Expansion Modules are optional uplinks for the AT-8216FXL/ MT, AT-8216FXL/VF, AT-8216FXL/SC, and AT-8224XL Fast Ethernet Switches. The expansion modules are designed to be installed into the two expansion slots on the front of each switch. The expansion modules, which can be installed in any combination, offer you flexbility in building or expanding your network. Figure 1 through Figure 5 show the front panels while Table 1 describes each expansion module.
Overview Figure 3 AT-A17 Expansion Module Figure 4 AT-A18 Expansion Module Figure 5 AT-A19 Expansion Module 2
AT-A1x Series Expansion Modules Quick Install Guide Table 1 Expansion Module Features Module Port Type AT-A15/SX 1000Base-SX AT-A15/LX 1000Base-LX Connector Cable Type1 Type Maximum Cable Length SC 50/125 micron multimode fiber 1,804 ft (550 m)2 62.5/125 micron multimode fiber 902 ft (275 m)3 9/125 micron singlemode fiber cable 6.2 mi (10 km) SC 50/125 or 62.5/125 1,804 ft (550 m)2 micron multimode fiber AT-A16 100Base-FX VF-45 50/125 or 62.
Overview Reviewing Safety Precautions Please review the following safety precautions before you begin to install the expansion module. Laser Warning Class 1 Laser product. ! 6 Laser Warning Do not stare into the Laser beam. ! 7 Warning Lightning Danger DO NOT WORK on equipment or CABLES during periods of LIGHTNING ACTIVITY. ! 8 Warning CAUTION: POWER CORD IS USED AS A DISCONNECTION DEVICE. TO DE-ENERGISE EQUIPMENT disconnect the power cord.
AT-A1x Series Expansion Modules Quick Install Guide Installing the Expansion Module To install an expansion module, perform the following steps: 1. Disconnect the switch’s power cord, if attached. Warning Make sure to disconnect the power cord before installing the expansion module. Installing an expansion module without doing so can damage the module. Warning The power cord is used as a disconnect device. To de-energize equipment, disconnect the power cord. ! 9 2.
Overview For example, if you install an AT-A17 in slot B while leaving slot A empty, the switch will assign the port numbers 25 and 26 to the ports on the module. If you later install another AT-A17 in slot A, the switch will automatically reallocate port numbers 25 and 26 to the new modules in slot A and assign the port numbers 27 and 28 to the module in slot B. If the module in slot B had been a member of a VLAN, you would be required to reconfigure the VLAN to reflect the change to its port numbers. 3.
AT-A1x Series Expansion Modules Quick Install Guide Note All modules except the AT-A18 modules are shipped with a dust cover over the ports. 8. Verify the LEDs on the expansion module’s front panel by referring to Table 2. Table 2 Expansion Module LEDs LED State Description Activity/Link Solid Green Indicates a 100 Mbps link. Flashing Green Indicates 100 Mbps activity. Solid Amber Indicates a 10 Mbps link (10/100 ports only). Flashing Amber Indicates 10 Mbps activity (10/100 ports only).
Overview Changing the GBIC Module in the AT-A15/SX or AT-A15/LX Expansion Module The AT-A15 (SX or LX) expansion module can be equipped with the AT-G8SX GBIC module for LED transmission of up to 1,804 ft (550 m) or the AT-G8LX GBIC module for laser transmission of up to 16,400 ft (5 km). This procedure explains how to change the GBIC module in an AT-A15 (SX or LX) module. The procedure assumes that the expansion module has been installed in the switch.
AT-A1x Series Expansion Modules Quick Install Guide 3. Slide the new GBIC module into the expansion slot and push it in until it clicks. Refer toFigure 9. AT-A15 ACTIVITY LINK A 1000BAS FULL DUP E-X COL HALF DUP B Figure 9 Installing a GBIC Module into the AT-A15 (SX or LX) Expansion Slot 4. Remove the dust cover and attach the fiber cables. It is important to leave the dust cover in place if you are not attaching the cables at this time. Dust in the ports will degrade transmission. 5.
Appendix A Translated Safety Information IMPORTANT: This appendix contains multiple-language translations for the safety statements in this guide. WICHTIG: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. VIGTIGT: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. BELANGRIJK: Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids.
Translated Safety Information STANDARDS: This product meets the following standards. U.S. Federal Communications Commission Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
AT-A1x Series Expansion Modules Quick Install Guide ! 11 OPERATING TEMPERATURE This product is designed for a maximum ambient temperature of 40 degrees C. ! 12 All Countries: Install product in accordance with local and National Electrical Codes. NORMEN: Dieses Produkt erfullt die Anforderungen der nachfolgenden Normen. !1 Hochfrequenzstörung !2 WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen ergreifen.
Translated Safety Information !6 ADVARSEL Laserprodukt av klasse 1. !7 ADVARSEL Stirr ikke på strålen. !8 FARE UNDER UVEJR FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med LYNAKTIVITET. !9 ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE STRØMMEN. SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen ud af stikket. ! 10 ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den omgivende luft i rummet for afkøling.
AT-A1x Series Expansion Modules Quick Install Guide NORMES: ce produit est conforme aux normes de suivantes: !1 Emission d’interférences radioélectriques !2 MISE EN GARDE: dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. !3 Immunité EN50082 - 1 1997 !4 Sécurité électrique TUV-EN60950, UL1950, CSA 950 !5 Laser EN60825 !6 ATTENTION Producit laser di classe 1.
Translated Safety Information !9 HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN VIRRANKATKAISULAITTEENA. VIRTA KATKAISTAAN irrottamalla virtajohto. ! 10 HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi. ! 11 KÄYTTÖLÄMPÖTILA Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle 40° C. ! 12 KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten sähköturvallisuusmääräysten mukaisesti.
AT-A1x Series Expansion Modules Quick Install Guide SIKKERHETSKRAV: Dette produktet tilfredsstiller folgende sikkerhetnormer: !1 RFI stråling !2 ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. !3 Immunitet EN50082-1 1997 !4 Elektrisk sikkerhet TUV-EN60950, UL1950, CSA 950 !5 Laser EN60825 !6 ADVARSEL Laserprodukt av klasse 1. !7 ADVARSAL Stirr ikke på strålen.
Translated Safety Information !9 CUIDADO: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM DISPOSITIVO DE DESCONEXÃO. PARA DESELETRIFICAR O EQUIPAMENTO, desconecte o cabo de ALIMENTAÇÃO. ! 10 CUIDADO: As aberturas de ventilação não devem ser bloqueadas e devem ter acesso livre ao ar ambiente para arrefecimento adequado do aparelho. ! 11 TEMPERATURA DE FUNCIONAMENTO Este produto foi projetado para uma temperatura ambiente máxima de 40 graus centígrados.
Translated Safety Information STANDARDER: Denna produkt uppfyller följande standarder. !1 Radiostörning !2 VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. !3 Immunitet EN50082-1 1997 !4 Elsäkerhet TUV-EN60950, UL1950, CSA 950 !5 Laser EN60825 !6 VARNING! Laserprodukt av klass 1. !7 VARNING! Laserstrålning när enheten är öppen.
Appendix B AT-A1x Series Expansion Module Quick Install Guide Feedback Please tell us what additional information you would like to see discussed in this guide. If there are topics you would like information on that were not covered in this guide, please photocopy this page, answer the questions and fax or mail this form back to Allied Telesyn. The mailing address and fax number are at the bottom of the page. Your comments are valuable when we plan future revisions of this guide.
Appendix C Technical Support Fax Order Name ________________________________________________________________________ Company_____________________________________________________________________ Address______________________________________________________________________ City ___________________________State/Province__________________________________ Zip/Postal Code ______________________ Country__________________________________ Phone __________________________________ Fax________________________________
Appendix D Where To Find Us For Technical Support or Service Location Phone Fax Americas United States, Canada, Mexico, Central America, South America 1 (800) 428-4835 1 (503) 639-3946 Asia Singapore, Taiwan, Thailand, Malaysia, Indonesia, Korea, Philippines, China, India, Hong Kong (+65) 3815-612 (+65) 3833-830 Australia Australia, New Zealand 1 (800) 000-880 (+61) 2-9438-4966 France France, Belgium, Luxembourg, The Netherlands, Middle East, Africa (+33) 1-60-92-15-25 (+33) 1-69-28-37-49 Ge