CONVERTEON™ Family Two-Slot Chassis AT-CV1200 AT-CV1203 Installation Guide 613-000331 Rev.
Copyright © 2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis is a trademark of Allied Telesis, Inc. Microsoft and Internet Explorer are registered trademarks of Microsoft Corporation. Netscape Navigator is a registered trademark of Netscape Communications Corporation.
Electrical Safety and Emissions Standards This product meets the following standards. U.S. Federal Communications Commission Radiated Energy Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Translated Safety Statements Important: The indicates that a translation of the safety statement is available in a PDF document titled Translated Safety Statements posted on the Allied Telesis website at www.alliedtelesis.com and on the documentation CD shipped with this product.
Contents Preface ................................................................................................................................................................................11 Safety Symbols Used in this Document................................................................................................................................12 Where to Find Web-based Guides .....................................................................................................................
Contents 6
Figures Figure 1. AT-CV120x Chassis .............................................................................................................................................16 Figure 2. AT-CV120x Chassis Front and Back Panels........................................................................................................17 Figure 3. AT-CV5M01 Management Card ...........................................................................................................................18 Figure 4.
Figures 8
Tables Table 1. Safety Symbols .....................................................................................................................................................12 Table 2. Power LEDs on the Rear Panel ............................................................................................................................
Tables 10
Preface This guide contains instructions on how to install the AT-CV1200 or AT-CV1203 two-slot Converteon chassis.
Preface Safety Symbols Used in this Document This document uses the safety symbols defined in Table 1. Table 1. Safety Symbols Symbol 12 Meaning Description Caution Performing or omitting a specific action may result in equipment damage or loss of data. Warning Performing or omitting a specific action may result in electrical shock.
AT-CV120x Two-Slot Chassis Installation Guide Where to Find Web-based Guides The installation and user guides for all Allied Telesis products are available in portable document format (PDF) on our web site at www.alliedtelesis.com. You can view the documents online or download them onto a local workstation or server.
Preface Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales or corporate information. Online Support You can request technical support online by accessing the Allied Telesis Knowledge Base from the following web site: www.alliedtelesis.com/support. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions.
Chapter 1 Overview This chapter contains the following sections: “Features” on page 16 “AT-CV5M0x Management Card” on page 18 “AT-CVMNT12 Wall-Mount Bracket” on page 19 “Blank Slot Cover” on page 20 “Power Adapter” on page 21 “Network Topologies” on page 23 15
Chapter 1: Overview Features The AT-CV1200 and AT-CV1203 chassis look physically the same, as shown in Figure 1. These chassis are dual-slot chassis for Converteon media converter line cards and the AT-CV5M0x Management Card. You can use the chassis as an unmanaged device by installing line cards in both slots, or you can add management capability with the AT-CV5M0x Management Card. The management card gives you management control over the line card located in the other slot.
AT-CV120x Two-Slot Chassis Installation Guide available from your Allied Telesis sales representative. Front and Back Panels Figure 2 shows the front and back panels of the AT-CV1200 chassis. The AT-CV1203 chassis is physically identical. AT-CV1200 Slot 2 2 CLASS 1 LASER PRODUCT Slot 1 1 544 AC Power Connector (PWR A) PWR GOOD PWR A PWR B 12VDC 12VDC 545 PWR Good LED Power Adapter LEDs AC Power Connector (PWR B) Figure 2.
Chapter 1: Overview AT-CV5M0x Management Card The AT-CV5M0x Management Card provides a CPU subsystem for the Allied Telesis Converteon Series chassis such as the AT-CV5000 and the AT-CV120x. The AT-CV5M0x Management Card is shipped with the management software preinstalled that allows you to configure and monitor the status of the media converter line cards in the chassis. Note The AT-CV120x supports only one AT-CV5M0x Management Card at a time. The AT-CV5M01 Management Card is shown in Figure 3.
AT-CV120x Two-Slot Chassis Installation Guide AT-CVMNT12 Wall-Mount Bracket The AT-CVMNT12 Wall-Mount Bracket, shown in Figure 4, is a bracket designed to mount an AT-CV120x chassis and one or two AC power adapters on the wall. 1015 Figure 4. AT-CVMNT12 Wall-Mount Bracket For instructions on how to mount the AT-CV120x chassis on the wall, using the bracket, refer to the installation guide shipped with the bracket.
Chapter 1: Overview Blank Slot Cover The AT-CV5PNL1 blank slot cover is designed to maintain optimal, trouble-free environmental conditions for the AT-CV120x chassis. An unoccupied line card slot on the AT-CV120x chassis should be covered with a blank slot cover to keep dust from getting into the chassis and maintain proper airflow, cooling, and ventilation throughout the chassis. Figure 5 illustrates the AT-CV5PNL1 blank slot cover. 222 Figure 5.
AT-CV120x Two-Slot Chassis Installation Guide Power Adapter The AT-CV120x chassis uses a two-part AC power adapter (supplied) as shown in Figure 6. 517 Figure 6. AC Power Adapter Note The AT-CV120x chassis is shipped with one power adapter. To order an additional power adapter for redundant power, contact your local Allied Telesis sales representative. For the AC power requirements, refer to “Power Specifications” on page 43.
Chapter 1: Overview LEDs Figure 7 shows the location of the rear panel power LEDs which are described in Table 1. PWR A PWR GOOD PWR B 12VDC 12VDC 545 PWR Good LED Power Adapter LEDs Figure 7. Power LEDs on the Rear Panel. Table 1. Power LEDs on the Rear Panel LED PWR GOOD PWR A PWR B 22 State Description Green Power is being supplied to the line cards. OFF Power is not being supplied to the line cards. Green Power adapter A is operating normally.
AT-CV120x Two-Slot Chassis Installation Guide Network Topologies This section describes the network topologies you can create with the AT-CV1200 Two-Slot Chassis. Figure 8 illustrates a standalone topology using an AT-CV1200 chassis with two AT-CM202 line cards, one of which is used to interconnect two small networks. Network 1 has an AT-FS709FC switch connected to the 100Base-FX port on the AT-CM202 line card in the AT-CV1200 media converter.
Chapter 1: Overview Back-to-Back Topology Figure 9 shows a back-to-back topology using two AT-CV1200 chassis with two AT-CM202 line cards, with one line card in each chassis used to interconnect two small networks. The media converters themselves are connected together through 100Base fiber optic ports on AT-CM202 line cards. Network 1 has an AT-8350GB switch connected to the 10/100Base-TX port on the AT-CM202 line card in the first AT-CV1200 media converter.
AT-CV120x Two-Slot Chassis Installation Guide 25
Chapter 1: Overview 26
Chapter 2 Installation This chapter contains the following installation procedures for the AT-CV120x chassis: “Reviewing Safety Precautions” on page 28 “Selecting a Site for the Chassis” on page 29 “Unpacking the Chassis” on page 30 “Using the AT-CV120x Chassis on a Desktop” on page 31 “Powering On an AT-CV120x Chassis” on page 32 “Installing a Converteon Line Card” on page 33 “Installing an AT-CM70S Line Card” on page 35 “Installing a Blank Slot Cover” on page 37 “Warra
Chapter 2: Installation Reviewing Safety Precautions Please review the following safety precautions before you begin to install the chassis or any of its components. Note The indicates that a translation of the safety statement is available in a PDF document titled Translated Safety Statements on the Allied Telesis website at www.alliedtelesis.com and on the documentation CD shipped with this product. Warning: Do not work on equipment or cables during periods of lightning activity.
AT-CV120x Two-Slot Chassis Installation Guide Selecting a Site for the Chassis Observe the following requirements when choosing a site for the chassis: The power outlet for the chassis should be located near the unit and should be easily accessible. The site should provide easy access to the ports on the front and the power supply on the back of the chassis. This arrangement will make it easy for you to connect and disconnect cables as well as to view the LEDs.
Chapter 2: Installation Unpacking the Chassis To unpack the chassis, perform the following procedure: 1. Remove all components from the shipping package. Note Store the packaging material in a safe location. You must use the original shipping material if you need to return the unit to Allied Telesis. 2. Make sure that the following components are included in the package. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance.
AT-CV120x Two-Slot Chassis Installation Guide Using the AT-CV120x Chassis on a Desktop To use the AT-CV120x chassis on a desktop, perform the following procedure: 1. Remove the chassis from the shipping container. 2. Turn the chassis over and place it on a secure surface. 3. Attach the four self-adhesive rubber feet, included, to the bottom of the chassis, as shown in Figure 10. 1 546 2 LA CL SE AS R PRS 1 OD UC T 20 V1 0 AT -C Figure 10. Attaching Rubber Feet 4. Turn the chassis over again. 5.
Chapter 2: Installation Powering On an AT-CV120x Chassis The AT-CV120x chassis is shipped with one AC power adapter which powers both slot 1 and slot 2. Note Use only power sources that are UL Listed (QQGQ or EPBU), TUV Licensed or other Safety Agencies approved, and that are suitable for country of use. To power on an AT-CV120x chassis, perform the following procedure: 1.
AT-CV120x Two-Slot Chassis Installation Guide Installing a Converteon Line Card To install any Converteon line card including the AT-CV5M0x Management Card, except for the AT-CM70S line card, perform the following procedure: Caution Be sure to observe all standard electrostatic discharge (ESD) precautions, such as wearing an antistatic wrist strap, to avoid damaging the device. A line card can be damaged by static electricity.
Chapter 2: Installation 5. Set the line card’s DIP switches if necessary. For more information on the DIP switch settings, refer to the documentation shipped with your line card. 6. Align the back edge of the line card with the left and right alignment guides located inside the slot. 7. Slide the line card into the slot, as shown in Figure 13, until the slot cover is flush with the front of the chassis.
AT-CV120x Two-Slot Chassis Installation Guide Installing an AT-CM70S Line Card The AT-CM70S line card is a double-slot line card which takes both line card slots in the AT-CV120x chassis. Caution Be sure to observe all standard electrostatic discharge (ESD) precautions, such as wearing an antistatic wrist strap, to avoid damaging the device. A line card can be damaged by static electricity. To install an AT-CM70S line card, perform the following procedure: 1.
Chapter 2: Installation 5. Align the back edge of the line card with the bottom left and right alignment guides located inside the slot. 6. Slide the AT-CM70S line card into the chassis, as shown in Figure 16, until the slot cover is flush with the front of the chassis. AATT --CC VV11 2200 00 TEST 1 903 AIS 1 RDY X T 2 3 4 L/A FD 100 C O N S O L E 4 2 3 4 3 2 RCL NML CPU RESET LOTC NML LK OAM S F P AT-CM70S 1 T1/E1 LA CL SE AS R PRS 1 OD UCT Figure 16.
AT-CV120x Two-Slot Chassis Installation Guide Installing a Blank Slot Cover The AT-CV5PNL1 blank slot covers are used to cover the unoccupied line card slots in the Converteon Series chassis. The AT-CV120x chassis is shipped with two line card slots covered with the AT-CV5PNL1 blank slot covers.
Chapter 2: Installation 8. Use a Phillips screwdriver to tighten the captive screw, as shown in Figure 19. AATT --CC VV11 2200 00 LA CL SE AS R PRS 1 OD UC T 2 1 550 Figure 19. Tightening the Captive Screw on an AT-CV5PNL1 Blank Slot Cover Note Always tighten the captive screw to secure the blank slot cover to the chassis.
AT-CV120x Two-Slot Chassis Installation Guide Warranty Registration Allied Telesis hardware products are covered under limited warranties. Some products have a longer warranty coverage than others. This AT-CV120x Chassis has a limited warranty of: Lifetime (2 years Fan & PSU) All ATI warranties are subject to the terms and conditions set out in the Allied Telesis Limited Warranties listed on the Allied Telesis website at http://alliedtelesis.com/support/warranty.
Chapter 2: Installation 40
Chapter 3 Troubleshooting This chapter contains information about how to troubleshoot the chassis and line cards in the event that a problem occurs. Note The AT-CV120x model chassis does not have a status LED. To troubleshoot a problem, refer to the LEDs on the line card or the AT-CV5M0x Management Card. Note If after following the instructions in this chapter you are unable to resolve the problem, contact Allied Telesis Technical Support for assistance.
Chapter 3: Troubleshooting If one of the power supplies is connected but its LED remains OFF, perform the following: Verify that the power cord of the power supply in question is securely connected to its connector and to the power source. Verify that the power outlet has power by connecting another device to it. Try connecting the unit to another power source. Try using a different power cord. Check that the voltage from the power source is within the required levels for your region.
Appendix A Technical Specifications Physical Specifications Dimensions: (H x W x L): 5.40 cm x 13.12 cm x 15.52 cm (2.12 in x 5.17 in x 6.11 in) Weight: 0.9 kg (1.98 lb) Environmental Specifications Operating Temperature: 0° C to 40° C (32° F to 104° F) Storage Temperature: -25° C to 70° C (-13°F to 158° F) Operating Humidity: 5% to 90% non-condensing Storage Humidity: 5% to 95% non-condensing Maximum Operating Altitude: 3,000 m (10,000 ft.) Maximum Storage Altitude: 4,000 m (13,100 ft.
Appendix A: Technical Specifications Safety and Electromagnetic Emissions Certifications EMI: FCC Class A, EN55022 Class A, VCCI Class A, C-TICK, CE Immunity: EN55024 Safety: UL60950-1 (CULUS), EN60950-1 (TUV), CAN/CSA C22.2 No. 60950-1 Laser: EN60825 Quality and Reliability: MTBF > 100,000 hrs.
