AT-FH705E V2 10/100Base Ethernet Switching Hub Installation Guide PN 613-50167-00 Rev A
Copyright 2000 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA USA 94085 All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn International, Corp.
Electrical Safety and Emission Statement Standards: This product meets the following standards. U.S. Federal Communications Commission DECLARATION OF CONFORMITY Manufacture Name: Allied Telesyn International Manufacture Address: 960 Stewart Drive, Suite B Sunnyvale, CA 94086 USA Manufacture Telephone: 408-730-0950 Declares that the product: Ethernet switching hub Model Number: AT-FH705E This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Belangrijk: Appendix A bevat vertaalde veiligheidsopmerkingen voor het installeren van deze ziet, raadpleeg Appendix A apparatuur. Wanneer u de voor vertaalde veiligheidsinstructies in uw taal. Important: L'annexe A contient les instructions de sécurité relatives à l'installation de cet équipement. Lorsque vous , reportez-vous à l'annexe A pour voyez le symbole consulter la traduction de ces instructions dans votre langue.
Table of Contents Electrical Safety and Emission Statement...................................................... iii Table of Contents ........................................vii Welcome to Allied Telesyn ........................ ix Where to Find Web-based Guides ................. ix Document Conventions .................................. ix Contacting Allied Telesyn ...............................x Online Support .........................................x Telephone or Fax Support ......................
Network Topologies .........................................7 Installing the AT-FH705E ..............................9 Verifying the Package Contents ..............9 Selecting a Site ........................................10 Reviewing Safety Guidelines ..................11 Installing the Unit on a Desktop ............13 Installing the Unit on a Wall..................14 Verifying and Troubleshooting the Installation......................................................16 Warranty Registration ..............
Welcome to Allied Telesyn This guide contains instructions on how to install an Allied Telesyn AT-FH705E Ethernet Switching Hub. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com provides you with an easy way to access the most recent documentation and technical information for all of our products. All web-based documents for Allied Telesyn products can be downloaded from the web site in PDF format.
Note A note provides additional information. Caution A caution indicates that performing or omitting a specific action may result in equipment damage or loss of data. Warning A warning indicates that performing or omitting a specific action may result in bodily injury. Contacting Allied Telesyn There are several ways to contact Allied Telesyn technical support: online, telephone, fax, and e-mail.
AT-FH705E Installation Guide Telephone or Fax Support For technical support via fax, please fill out the“Technical Support Fax Order” on page 35 and send it to the appropriate location listed below.
E-mail Support United States and Canada TS1@alliedtelesyn.com Latin America, Mexico, Puerto Rico, Caribbean, and Virgin Islands latin_america@alliedtelesyn.com United Kingdom, Sweden, Norway, Denmark, and Finland support_europe@alliedtelesyn.com Returning Products Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesyn without a RMA number will be returned to the sender at the sender’s expense.
AT-FH705E Installation Guide Latin America, the Caribbean, Virgin Islands Tel: international code + 425-481-3852 Fax: international code + 425-483-9458 Mexico and Puerto Rico Tel: 1-800-424-5012, ext 3852 or 1-800-424-4284, ext 385 2 Mexico only: 95-800-424-5012, ext 3852 Fax: international code + 425-489-9191 FTP Server If you need a device driver for an Allied Telesyn device and you know the name of the driver, you can download the software by connecting directly to our FTP server at ftp://gateway.
For Sales or Corporate Information For sales or corporate information contact Allied Telesyn at one of the following locations: Allied Telesyn International, Corp. 19800 North Creek Parkway, Suite 200 Bothell, WA 98011 Tel: 1 (425) 487-8880 Fax: 1 (425) 489-9191 Allied Telesyn International, Corp.
AT-FH705E Fast Ethernet Switching Hub Overview The AT-FH705E is a 10Base-T/100Base-TX unmanaged switching hub. The device provides you with a simple, cost-effective solution for Ethernet connectivity between end nodes operating at either 10 or 100 Mbps. 100M 7.
Features The AT-FH705E Switching Hub has the following features: ❑ Five auto-negotiating 10/100 Mbps twisted pair ports with RJ-45 connectors ❑ One Uplink port for connecting the ATFH705E Switching Hub to another switch or hub without a crossover cable ❑ IEEE 802.3 and IEEE 802.3u compliant ❑ External power adapter ❑ Desktop or wall-mount installation Figure 2 and Figure 3 show the front and back panels of the hub. 100M FH705E 7.
AT-FH705E Installation Guide Uplink 5 4 3 2 1 Figure 3 Back Panel Physical Description The physical description of the device includes: ❑ Ports 1 through 4 ❑ Port 5 and the Uplink port ❑ LEDs ❑ Power supply Ports 1 Through 4 Ports 1 through 4 can operate at either 10 Mbps or 100 speed and in either full- or half-duplex mode. The ports, featuring RJ-45 connectors, are configured as MDI-X, meaning that you can connect a workstation or server to one of the ports without using a crossover cable.
The ports are IEEE802.3u Auto-Negotiation compliant. This means that the ports can automatically configure their speed and duplex mode to match the capabilities of the end nodes connected to the ports. Port 5 and the Uplink Port Port 5 and the Uplink port allow you to connect an additional workstation to the hub or interconnect the switching hub with another switch or hub, without the use of a cross-over cable.
AT-FH705E Installation Guide Front Panel LEDs Refer to Table 1 for a description of the device LEDs. Table 1 LED Functions LEDs Color Description Power Green On means there is power to the hub. Off means there is no power to the hub. 100M Green On means the port speed is 100 Mbps. Off means the port speed is 10 Mbps. Link/Act Green On indicates a valid physical link on the port. Flashing indicates data is being transmitted or received on the port. Off means there is no link on the port.
Table 1 LED Functions (continued) LEDs Color Description Fdx/Hdx Green On indicates the port is operating in full-duplex mode. Off indicates the port is operating in half-duplex mode. Power Supply The AT-FH705E uses an external power adapter that comes standard with the hub.
AT-FH705E Installation Guide Network Topologies Figure 4 illustrates a network that consists of one AT-FH705E Ethernet Switching Hub used to interconnect four workstations and a server. In this configuration, the Uplink port is not used.
Figure 5 illustrates a network of two ATFH705E Ethernet Switching Hubs that have been interconnected using the Uplink ports on the two units. Using the Uplink ports eliminates the need for a cross-over cable to interconnect the hubs.
AT-FH705E Installation Guide Installing the AT-FH705E This section contains the procedures for installing the device. Verifying the Package Contents Make sure that the package includes the following items. If any of the items are damaged or missing, contact your Allied Telesyn representative immediately.
Selecting a Site Make sure you observe the following site requirements: ❑ Make sure you are placing the device in a dust-free and moisture-free environment. ❑ Do not block the ventilation openings on the unit. Allow at least 10 centimeters (4 inches) of space at the front and back of the unit for ventilation. ❑ Make sure that the device’s power is accessible and cables can be connected easily.
AT-FH705E Installation Guide ❑ Observe the following cabling specifications: Ports Connector Type Type of Cable Maximum Distance 1 through 5 RJ-45 Category 5 100 m (328 ft) Uplink RJ-45 Category 5 100 m (328 ft) Reviewing Safety Guidelines Please review the following safety guidelines before you begin to install the device. Warning Power cord is used as a disconnection device: To deenergize equipment, disconnect the power cord.
Caution EUROPE - EU: Use TÜV licensed AC adapter of DC 7.5V, 1A. 7 Caution USA/CANADA: Use a UL Listed/CSA Certified AC adapter of DC 7.5V, 1A. 7 Caution Australia: Use a Australian Safety Approved AC adapter of DC 7.5V 1A. 7 Caution Air vents: The air vents must not be blocked on the unit and must have free access to the room ambient air for cooling. 8 Caution Operating Temperature: This product is designed for a maximum ambient temperature of 40°C.
AT-FH705E Installation Guide Installing the Unit on a Desktop To install the device on a desktop, perform the following procedure. To mount the unit on a wall, perform the steps “Installing the Unit on a Wall” on page 14. 1. Attach the four self-adhesive rubber feet to the bottom of the device, positioning them in the indentations. 2. Place the device on a flat, level surface. 3.
5. Attach the data cables to the switching hub ports. Do not use a cross-over cable to connect workstations or servers to ports 1 through 5. Do not use a cross-over cable to connect another switch or hub to the Uplink port. Note You can use either port 5 or the Uplink port on an AT-FH705E Switching Hub, but you cannot use both simultaneously. 6. Go to the procedure “Verifying and Troubleshooting the Installation” on page 16.
AT-FH705E Installation Guide Note For wall-mount installation, you must supply the two screws and plastic anchors or other material necessary to physically mount the device on the wall. 3. Install two plastic anchors and two pan-head screws into the wall, separated by 5 centimeters (approximately 2 inches). 4. Position the device onto the wall screws. 5. Plug the power adapter into the power receptacle, then plug the DC power cord into the DC connector on the front panel of the switching hub.
7. Attach the data cables to the AT-FH705E ports. Do not use a cross-over cable to connect workstations or servers to ports 1 through 5. Do not use a cross-over cable to connect another AT-FH705E to the Uplink port. Note You can use either port 5 or the Uplink port, but you cannot use both simultaneously. 8. Go to the procedure “Verifying and Troubleshooting the Installation” on page 16.
AT-FH705E Installation Guide AT-FH705E Switching Hub. ❑ Check to be sure that the power outlet has power by connecting another device to it. ❑ Try replacing the power adapter with another power adapter. 2. Check the Link/Act LED for each port. The LED should be lit steady or flashing. If a Link/Act LED is OFF, check the following: ❑ Check to be sure that the node connected to the port on the AT-FH705E is powered ON. If the node is OFF, power the unit ON.
3. If the Lnk/Act LED for a port is on but there is a communication problem to the end node connected to the port, such as the loss of data, check the following: ❑ Check to be sure that the distance between the AT-FH705E and the connected network device is no greater than 100 meters (328 feet). ❑ Check to be sure that you are using Category 5 cable.
AT-FH705E Installation Guide Technical Specifications Standards Compatibility: IEEE 802.3, IEEE802.3u Interfaces: RJ-45 connectors Physical Dimensions: WxDxH 100 x 78.5 x 26 mm (3.93 x 3.09 x 1.02 in.) Power Supply: Output: 7.
Appendix A Translated Safety and Emission Information Important: This appendix contains multiplelanguage translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids.
Importante: questa appendice contiene traduzioni in più lingue degli avvisi di sicurezza di questa guida. Viktig: Dette tillegget inneholder oversettelser til flere språk av sikkerhetsinformasjonen i denne veiledningen. Importante: Este anexo contém traduções em vários idiomas das advertências de segurança neste guia. Importante: Este apéndice contiene traducciones en múltiples idiomas de los mensajes de seguridad incluidos en esta guía.
AT-FH705E Installation Guide Standards: This product meets the following standards: U.S. Federal Communications Commission DECLARATION OF CONFORMITY Manufacture Name: Allied Telesyn International Manufacture Address: 950 Stewart Drive, Suite B Sunnyvale, CA 94085 USA 408-730-0950 Manufacture Telephone: Declares that the product: Ethernet switching hub Model Number: AT-FH705E This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules.
Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
AT-FH705E Installation Guide 9 OPERATING TEMPERATURE: This product is designed for a maximum ambient temperature of 40° degrees C. 10 ALL COUNTRIES: Install product in accordance with local and National Electrical Codes. Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen. 1 Hochfrequenzstörung 2 WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen ergreifen.
26 Standarder: Dette produkt tilfredsstiller de følgende standarder. 1 Radiofrekvens forstyrrelsesemission: EN55022 Klasse B 2 ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. 3 Immunitet EN50082-1 1997 4 Elektrisk sikkerhed UL 1950 (UL, cUL), EN60950, VCCI Class B SIKKERHED 5 ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE STRØMMEN.
AT-FH705E Installation Guide Eisen: Dit product voldoet aan de volgende eisen. 1 RFI Emissie 2 WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen. 3 Immuniteit 4 Electrische Veiligheid EN55022 Klasse B EN50082-1 1997 UL 1950 (UL, cUL), EN60950, VCCI Class B VEILIGHEID 5 WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR DE STROOMKABEL TE ONTKOPPELEN.
28 Normes: ce produit est conforme aux normes de suivantes. 1 Emission d’interférences radioélectriques EN55022 Classe B 2 MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates.
AT-FH705E Installation Guide Standardit: Tämä tuote on seuraavien standardien mukainen. 1 Radioaaltojen häirintä 2 VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin. 3 Kestävyys EN50082-1 1997 4 Sähköturvallisuus UL 1950 (UL, cUL), EN60950, VCCI Class B EN55022 Luokka B TURVALLISUUS 5 HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN VIRRANKATKAISULAITTEENA.
30 Standard: Questo prodotto è conforme ai seguenti standard. 1 Emissione RFI (interferenza di radiofrequenza) EN55022 Classe B 2 AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti.
AT-FH705E Installation Guide Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. 1 RFI stråling 2 ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. 3 Immunitet EN50082-1 1997 4 Elektrisk sikkerhet UL 1950 (UL, cUL), EN60950, VCCI Class B EN55022 Klasse B SIKKERHET 5 FORSIKTIG: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET.
32 Padrões: Este produto atende aos seguintes padrões. 1 Emissão de interferência de radiofrequência EN55022 Classe B 2 AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas. 3 Imunidade EN50082-1 1997 4 Segurança Eléctrica UL 1950 (UL, cUL), EN60950, VCCI Class B SEGURANÇA 5 CUIDADO: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM DISPOSITIVO DE DESCONEXÃO.
AT-FH705E Installation Guide Estándares: Este producto cumple con los siguientes estándares. 1 Emisión RFI 2 ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto.
Standarder: Denna produkt uppfyller följande standarder. 1 Radiostörning 2 VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. 3 Immunitet EN50082-1 1997 4 Elsäkerhet UL 1950 (UL, cUL), EN60950, VCCI Class B 34 EN55022 Klass B SÄKERHET 5 VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT KOPPLA FRÅN STRÖMMEN, dra ur nätkabeln.
Appendix B Technical Support Fax Order Name __________________________________ Company _______________________________ Address ________________________________ City____________________________________ State/Province __________________________ Zip/Postal Code ________________________ Country ________________________________ Phone __________________________________ Fax ___________________________________ Incident Summary Model number of Allied Telesyn product I am using______________________________ Firmwa
Brief summary of problem _______________ _______________________________________ Conditions (List the steps that led up to the problem. _________________________ _______________________________________ _______________________________________ Detailed description (Please use separate sheet) Please also fax printouts of relevant files such as batch files and configuration files. When completed, fax this sheet to the appropriate Allied Telesyn office. Fax numbers can be found on page viii.
Appendix C AT-FH705E Installation Guide Feedback Please tell us what additional information you would like to see discussed in this guide. You can fax or mail this form to the mailing address and fax number at the bottom of the page.
