AT-FS705LE 10/100Base Ethernet Switch Installation Guide PN 613-50138-00 Rev C
Copyright 2002 Allied Telesyn, Inc. 960 Stewart Drive Suite B, Sunnyvale CA USA 94086 All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn, Inc.
Electrical Safety and Emission Statement Standards: This product meets the following standards. U.S. Federal Communications Commission Declaration Of Conformity Manufacture Name: Allied Telesyn, Inc. Manufacture Address: 960 Stewart Drive, Suite B Sunnyvale, CA 94086 USA Manufacture Telephone: 408-730-0950 Declares that the product: Ethernet Switch Model Number: AT-FS705LE This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Belangrijk: Appendix A bevat vertaalde veiligheidsopmerkingen voor het installeren van deze ziet, raadpleeg Appendix A apparatuur. Wanneer u de voor vertaalde veiligheidsinstructies in uw taal. $ Important: L'annexe A contient les instructions de sécurité relatives à l'installation de cet équipement. Lorsque vous , reportez-vous à l'annexe A pour voyez le symbole consulter la traduction de ces instructions dans votre langue.
Table of Contents Electrical Safety and Emission Statement ................................. iii Welcome to Allied Telesyn ........................ ix Where to Find Web-based Guides ................. ix Document Conventions .................................. ix Contacting Allied Telesyn Technical Support .........................................x Online Support .........................................x Telephone Support .................................. xi E-mail Support .................................
Network Topologies .........................................6 Installing the Switch .......................................8 Verifying the Package Contents ..............8 Selecting a Site .........................................9 Reviewing Safety Guidelines ..................10 Installing the Switch on a Desktop ........12 Installing the Switch on a Wall ..............14 Warranty Registration ...................................16 Troubleshooting ..............................................
Welcome to Allied Telesyn This guide contains instructions on how to install the AT-FS705LE Ethernet Switch. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com offers you an easy way to access the most recent documentation, software, and technical information for all of our products. For product guides, select “Support & Services” from our web site. Document Conventions This guide uses the following conventions: Note A note provides additional information.
Caution Cautions informs you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings informs you that performing or omitting a specific action may result in bodily injury. Contacting Allied Telesyn Technical Support You can contact Allied Telesyn technical support online or by telephone or e-mail. Online Support You can request technical support online by accessing the Knowledge Base at kb.alliedtelesyn.com.
AT-FS705LE Installation Guide Telephone Support For technical support by phone, contact Allied Telesyn at one of the following locations: Americas United States, Canada, Mexico, Central America, South America Tel: 1 (800) 428-4835 Germany Switzerland, Austria, Eastern Europe Tel: (+49) 30-435-900-126 Asia Singapore, Taiwan, Thailand, Malaysia, Indonesia, Korea, Philippines, China, India, Hong Kong Tel: (+65) 3815-612 Italy Spain, Portugal, Greece, Turkey, Israel Tel: (+39) 02-41-30-41 Australia Tel: 1
Returning Products Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesyn without a RMA number will be returned to the sender at the sender’s expense.
AT-FS705LE Installation Guide FTP Server If you need management software for an Allied Telesyn managed device and you know the file name of the software, you can download the software by connecting directly to our FTP server at ftp:alliedtelesyn.com. At login, enter ‘anonymous’ for the user name and your e-mail address for the password. For Sales or Corporate Information You can contact Allied Telesyn for sales or corporate information at the location below: Allied Telesyn, Inc.
AT-FS705LE Fast Ethernet Switch Overview The AT-FS705LE Ethernet Switch is a 10Base-T/100Base-TX unmanaged switch. The switch provides you with a simple, cost-effective solution for Ethernet switching between endnodes operating at either 10 Mbps or 100 Mbps. Figure 1 and Figure 2 show the front and back panels of the switch.
Figure 2 AT-FS705LE Back Panel Features The AT-FS705LE switch has the following features: ❑ Five auto-negotiating 10/100 Mbps twisted pair ports with RJ-45 connectors ❑ One Uplink port for connecting the AT-FS705LE switch to another switch or hub without a crossover cable ❑ IEEE 802.3 and IEEE 802.
AT-FS705LE Installation Guide Physical Description The physical description for the switch includes: ❑ Ports 1 through 4 ❑ Port 5 and the Uplink port ❑ LEDs ❑ Power supply Ports 1 Through 4 Ports 1 through 4 can operate at either 10 Mbps or 100 Mbps and in either half- or full-duplex mode. The ports, featuring RJ-45 connectors, are configured as MDI-X, meaning that you can connect a workstation or server to one of the ports without using a crossover cable.
Port 5 and the Uplink Port Port 5 and the Uplink port allow you to connect an additional workstation to the switch or interconnect the switch with another switch or hub, without the use of a crossover cable. If you need to connect an additional workstation to the switch, use Port 5, which is configured as MDI-X. If you need to connect the switch to another Ethernet switch, use the Uplink port, which is configured as MDI.
AT-FS705LE Installation Guide Status LEDs Refer to Table 1 for a description of the switch’s LEDs. Table 1 LEDs LEDs Color Description PWR Green Power is applied to the switch. 100M Green The port is operating at 100 Mbps. OFF The port is operating at 10 Mbps. Green A valid link has been established on the port. Flashing Data is being transmitted or received on the port. Green The port is operating in full-duplex mode. OFF The port is operating in half-duplex mode.
Power Supply The AT-FS705LE switch uses an external AC/ DC power adapter that comes standard with the switch. Network Topologies Figure 3 illustrates a network that consists of one AT-FS705LE switch used to interconnect four workstations and a server. In this configuration, the Uplink port is not used.
AT-FS705LE Installation Guide Figure 4 illustrates a network of two AT-FS705LE switches that have been interconnected using the Uplink ports on the two units. Using the Uplink ports eliminates the need for a crossover cable to interconnect the switches.
Installing the Switch This section contains the procedures for installing the switch. Verifying the Package Contents Make sure the following items are included in your package. If any item is missing or damaged, contact your Allied Telesyn sales representative for assistance.
AT-FS705LE Installation Guide Selecting a Site Be sure to observe the following requirements when choosing a site for your switch. ❑ Make sure you are placing the switch in a dust-free and moisture-free environment. ❑ Do not block the ventilation openings on the unit. Allow at least 10 centimeters (4 inches) of space at the front and back of the unit for ventilation. ❑ Make sure that the switch’s power is accessible and cables can be connected easily.
❑ Observe the following cabling specifications: Ports Connector Type Type of Cable Maximum Distance 1 through 5 RJ-45 Category 5 100 m (328 ft) Uplink RJ-45 Category 5 100 m (328 ft) Reviewing Safety Guidelines Please review the following safety guidelines before installing the switch. Warning Power cord is used as a disconnection device. To de-energize equipment, disconnect the power cord.
AT-FS705LE Installation Guide Caution Air vents: The air vents must not be blocked on the unit and must have free access to the room ambient air for cooling. $7 Caution Operating Temperature: This product is designed for a maximum ambient temperature of 40°C. $ 8 Caution All Countries: Install this product in accordance with local and National Electric Codes. $ 9 Caution Europe - EU: Use TÜV licensed AC adapter of DC 7.5V, 1A. $ 10 Caution USA/Canada: Use a UL Listed/CSA Certified AC adapter of DC 7.
Installing the Switch on a Desktop To use the switch on the desktop, perform the following procedure. To wall-mount the switch, refer to “Installing the Switch on a Wall” on page 14. 1. Remove all the items from the shipping package and store the packaging material in a safe place. 2. Attach the four self-adhesive rubber feet to the bottom of the switch, positioning them in the indentations. 3. Place the switch on a flat, level surface. Warning The power cord is used as a disconnection device.
AT-FS705LE Installation Guide 6. Attach the data cables to the switch ports. Do not use a crossover cable to connect workstations or servers to ports 1 through 5. Do not use a crossover cable to connect another switch or hub to the Uplink port. Note You can use either Port 5 or the Uplink port, but you cannot use both simultaneously. 7. Power ON the end-nodes. 8. Check that the LINK/ACT LEDs for each port on the switch are green. If the LEDs are OFF, refer to “Troubleshooting” on page 16 for instructions.
Installing the Switch on a Wall For wall-mount installation, you can position the switch vertically or horizontally using the keyhole cutouts in the bottom of the switch. 1. If previously attached, remove the rubber feet, data cables, and the DC power cord from the switch. 2. Select a wall location for the switch. Note For wall-mount installation, the screws, plastic anchors, and any other material necessary to physically mount the switch to the wall are not provided. 3.
AT-FS705LE Installation Guide 5. Plug the AC/DC power adapter into an appropriate AC power outlet and insert the power plug into the DC receptacle located on the front of the switch. 6. Make sure the PWR LED, is green. If the LED is OFF, refer to “Troubleshooting” on page 16. 7. Attach the data cables to the switch ports. Do not use a crossover cable to connect workstations or servers to ports 1 through 5. Do not use a crossover cable to connect another AT-FS705LE switch to the Uplink port.
Warranty Registration When you have finished installing the product, register your product by completing the enclosed warranty card and sending it in. You can also fill out the registration online by selecting “Warranties” under “Support & Services” from www.alliedtelesyn.com. Troubleshooting Follow the guidelines below to test and troubleshoot the installation in the event a problem occurs.
AT-FS705LE Installation Guide If the LINK/ACT LED is OFF, do the following: ❑ Check to be sure that the end-node connected to the port on the switch is powered ON. If the end-node is OFF, power the unit ON. ❑ Check that the cable is securely connected to the port on the switch and on the endnode. ❑ Check to be sure that the distance between the switch and the end-node does not exceed 100 meters (328 feet). ❑ Check to be sure that you are using Category 5 cable.
Technical Specifications Physical Dimensions: WxDxH 100 x 78.5 x 26 mm (3.93 x 3.09 x 1.02 in) Temperature Maximum Operating 0° to 40° C Maximum Storage -25° to 70° C Operating Humidity 10% to 90% Relative Humidity Electrical Rating Input Supply Voltage: 7.5V @ 1A Power Consumption: 4W Agency Compliance Standards Compatibility: Electromagnetic Emission: 18 IEEE 802.3 IEEE802.
Appendix A Translated Safety and Emission Information Important: This appendix contains multiplelanguage translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids.
Importante: questa appendice contiene traduzioni in più lingue degli avvisi di sicurezza di questa guida. Viktig: Dette tillegget inneholder oversettelser til flere språk av sikkerhetsinformasjonen i denne veiledningen. Importante: Este anexo contém traduções em vários idiomas das advertências de segurança neste guia. Importante: Este apéndice contiene traducciones en múltiples idiomas de los mensajes de seguridad incluidos en esta guía.
AT-FS705LE Installation Guide Standards: This product meets the following standards: U.S. Federal Communications Commission Declaration Of Conformity Manufacture Name: Allied Telesyn, Inc. Manufacture Address: 960 Stewart Drive, Suite B Sunnyvale, CA 94086 USA Manufacture Telephone: 408-730-0950 Declares that the product: Ethernet Switch Model Number: AT-FS705LE This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules.
Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
$ AT-FS705LE Installation Guide 11 USA/Canada: Use a UL Listed/CSA Certified AC adapter of DC 7.5V, 1A. Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen. $ $ 1 Hochfrequenzstörung 2 $ $ Warnung: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen ergreifen.
$ $ $ $ $ $ $ $ $ $ 24 Standarder: Dette produkt tilfredsstiller de følgende standarder. 1 Radiofrekvens forstyrrelsesemission: EN55022 Klasse B 2 Advarsel: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. 3 Immunitet EN50082-1 1997 4 Elektrisk sikkerhed UL 1950, EN60950, VCCI Class B Sikkerhed 5 Advarsel: Den strømførende ledning bruges til at afbryde strømmen.
AT-FS705LE Installation Guide Eisen: Dit product voldoet aan de volgende eisen. $ $ 1 RFI Emissie 2 $ $ Waarschuwing: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen. 3 Immuniteit 4 Electrische Veiligheid $ $ $ $ $ $ EN55022 Klasse B EN50082-1 1997 UL 1950, EN60950, VCCI Class B Veiligheid 5 Waarschuwing: Het toestel wordt uitgeschakeld door de stroomkabel te ontkoppelen.
$ $ $ $ $ $ $ $ $ $ 26 Normes: ce produit est conforme aux normes de suivantes. 1 Emission d’interférences radioélectriques EN55022 Classe B 2 Mise En Garde: Dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. 3 Immunité EN50082 - 1 1997 4 Sécurité électrique UL 1950, EN60950, VCCI Class B 5 Danger De Foudre Danger: Ne pas manier le matériel ou les câbles lors d’activité orageuse.
AT-FS705LE Installation Guide Standardit: Tämä tuote on seuraavien standardien mukainen. $ $ 1 Radioaaltojen häirintä 2 $ $ Varoitus: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin. 3 Kestävyys EN50082-1 1997 4 Sähköturvallisuus UL 1950, EN60950, VCCI Class B $ $ $ $ $ $ EN55022 Luokka B Turvallisuus 5 Huomautus: Virtajohtoa käytetään virrankatkaisulaitteena.
$ $ $ $ $ $ $ $ $ $ 28 Standard: Questo prodotto è conforme ai seguenti standard. 1 Emissione RFI (interferenza di radiofrequenza) EN55022 Classe B 2 Avvertenza: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti.
AT-FS705LE Installation Guide Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. $ $ 1 RFI stråling 2 $ $ Advarsel: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. 3 Immunitet EN50082-1 1997 4 Elektrisk sikkerhet UL 1950, EN60950, VCCI Class B $ $ $ $ $ $ EN55022 Klasse B Sikkerhet 5 Forsiktig: Strømledningen brukes til å frakoble utstyret.
$ $ $ $ $ $ $ $ $ $ 30 Padrões: Este produto atende aos seguintes padrões. 1 Emissão de interferência de radiofrequência EN55022 Classe B 2 Aviso: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas. 3 Imunidade EN50082-1 1997 4 Segurança Eléctrica UL 1950, EN60950, VCCI Class B Segurança 5 Cuidado: O cabo de alimentação é utilizado como um dispositivo de desconexão.
AT-FS705LE Installation Guide Estándares: Este producto cumple con los siguientes estándares. $ $ 1 Emisión RFI 2 $ $ Advertencia: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto.
Standarder: Denna produkt uppfyller följande standarder. $ $ 1 Radiostörning 2 $ $ Varning: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. 3 Immunitet EN50082-1 1997 4 Elsäkerhet UL 1950, EN60950, VCCI Class B $ $ $ $ $ $ 32 EN55022 Klass B Säkerhet 5 Varning: Nätkabeln används som strömbrytare för att koppla från strömmen, dra ur nätkabeln. 6 Utrustning Med Plugg.
