AT-FS909SX Fast Ethernet Switch Installation Guide PN 613-10846-00 Rev A
Copyright 2000 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA 94086 USA All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn International Corp.
Electrical Safety and Emission Compliance Statement Standards: This product meets the following standards U.S. Federal Communications Commission RADIATED ENERGY Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Electrical Safety and Emission Compliance Statement IMPORTANT: Appendix A contains translated safety statements for installing this equipment. When you see the !, go to Appendix A for the translated safety statement in your language. WICHTIG: Anhang A enthält übersetzte Sicherheitshinweise für die Installation dieses Geräts. Wenn Sie ! sehen, schlagen Sie in Anhang A den übersetzten Sicherheitshinweis in Ihrer Sprache nach.
Table of Contents Electrical Safety and Emission Compliance Statement ......................iii Welcome to Allied Telesyn ......................................................................... vii Where to Find Web-based Guides ................................................................... vii Documentation Conventions............................................................................ vii Contacting Allied Teleysn ............................................................................
Table of Contents Appendix A Translated Safety and Emission Information ....................................... 17 Appendix B Technical Specifications ............................................................................ 29 Physical Specifications ..................................................................................... 29 Environmental Specifications .......................................................................... 29 Power Specifications .......................................
Welcome to Allied Telesyn The guide provides the required information to install and configure the AT-FS909SX Fast Ethernet Switch. Where to Find Web-based Guides Allied Telesyn wants our customers to be well informed by providing the most up-to-date and most easily accessible way to find our guides and other technical information. Visit our website at www.alliedtelesyn.com/techhome.htm for related product information.
Welcome to Allied Telesyn Contacting Allied Teleysn For Technical Support and Services Americas United States, Canada, Mexico, Central America, South America Tel: 1 (800) 428-4835 Fax: 1 (503) 639-3176 Germany Germany, Switzerland, Austria, Eastern Europe Tel: (+49) 30-435-900-126 Fax: (+49) 30-435-70-650 Asia Singapore, Taiwan, Thailand, Malaysia, Indonesia, Korea, Philippines, China, India, Hong Kong Tel: (+65) 3815-612 Fax: (+65) 3833-830 Italy Italy, Spain, Portugal, Greece, Turkey, Israel Tel: (+39
AT-FS909SX Installation Guide FTP Server Address: gateway.centre.com [lowercase letters] Login: anonymous [lowercase letters] Password: your e-mail address [requested by the server at login] For Sales or Corporate Information Allied Telesyn International, Corp. 19800 North Creek Parkway, Suite 200 Bothell, WA 98011 Tel: 1 (425) 487-8880 Fax: 1 (425) 489-9191 Allied Telesyn International, Corp.
Chapter 1 Product Description This chapter describes the features of the AT-FS909SX Fast Ethernet Switch. Features The AT-FS909SX is an unmanaged, Fast Ethernet Switch that provides familiar Ethernet technology with high-speed access. It is a high-performance switch that can be installed on the desktop, or into a 19-inch rack.
Product Description Physical Description Figure 1 shows the front panel of the switch. Figure 1 The AT-FS909SX Switch (Front) Figure 2 shows the rear view of the switch showing the AC input and fan locations. Figure 2 Rear View of the Switch Figure 3 shows the labels for the LEDs indicators for the two types of ports.
AT-FS909SX Installation Guide LEDs Table 1 describes the switch LEDs. Refer to Figure 3 for the labels for the LEDs for the two types of ports. Table 1 AT-FS909SX LED Indicators LED Color Indicates Power Green On The switch is powered up and ready for use. Off The switch is powered off. Gigabit Ethernet Port Status LEDs Col/Full Link/Act Orange On Link is present, full-duplex operation. Orange Flashing Link is present. Off Link is not present. Orange On Link is present on this port.
Product Description MDI Button The MDI provides you with the flexibility for using a straight-through cable to connect to a hub or another switch, or to any DTE such as an end station or a server. The button is associated with Port 1. Table 2 describes the MDI button positions.
AT-FS909SX Installation Guide AC Power Connector The switch has a single AC power supply socket in the rear panel, which has autoranging AC voltage inputs. The input voltage range is 100-240 VAC, 50/60 Hz. The power cord acts as an ON/OFF switch. Where to Go Next Proceed to Chapter 2 for details on how to install the switch.
Chapter 2 Installation This chapter describes the how to install the AT-FS909SX on a desktop, or into a 19-inch rack. Verifying Switch Package Contents Make sure the following items are included in your switch package. If any of the following items are missing or damaged, contact your sales representative.
Installation Preparing the Site Use common sense when selecting a location for the switch and observe the following: ❑ Make sure that the switch’s power is accessible and cables can be connected easily. ❑ Cabling must be away from sources of electrical noise such as radios, transmitters, broadband amplifiers, power lines, electric motors, and fluorescent fixtures. ❑ Air flow around the switch and through its vents on the side and rear must not be restricted.
AT-FS909SX Installation Guide Installing the Switch on a Desktop 1. Locate a level, secure surface for the switch. 2. Apply the four rubber feet to the bottom of the switch. 3. Place the switch on the desktop. Warning The power cord is used as a disconnection device. To de-energize equipment, disconnect the power cord. ! 10 4. Apply power to the switch by plugging the power cord into the rear of the unit and plugging the other end into a wall outlet. Verify that the Power LED lights green.
Installation Installing the Switch into a Rack Mount Caution Do not use power tools to perform this installation. 1. Remove all cables and the power cord from the switch (if previously attached). Caution Air vents must not be blocked and must have free access to the room ambient air for cooling. ! 13 2. Attach the rackmounting brackets to each side of the switch as shown in Figure 4, using the eight flathead screws that came in the switch package.
AT-FS909SX Installation Guide Warning Do not stare into the laser beam. ! 7 6. Connect the data cables and observe normal operation as indicated by the port LEDs. Refer to Table 1 on page 3 for LED information. For Port 1, set the MDI Button to the correct setting. Refer to Table 2 on page 4 for the MDI setting. 7. Optional: place one of the additional serial number stickers supplied with your switch on an accessible part of the switch for your convenient reference.
Chapter 3 Troubleshooting This chapter provides information on how to detect and resolve problems with your switch. This chapter includes the following sections: ❑ How the Switch Reports Problems ❑ Network Cabling Problems ❑ Common Problems ❑ Calling Technical Support How the Switch Reports Problems The LEDs indicate problems with the ports and power. See Table 1 on page 3 for a description of the switch LEDs.
Troubleshooting Link /Activity LED on Any Port is OFF This can indicate: ❑ A loose data cable. ❑ The device at the other end of the connection is turned OFF. ❑ The data cable is not wired correctly (straight/crossed) for the device. Perform the following steps in sequence; you need not proceed to the next step if the problem is resolved: 1. Make sure the data cables are secure. 2. Make sure the device at the end of the connection is turned ON. 3.
AT-FS909SX Installation Guide Calling Technical Support When contacting Allied Telesyn for support on any of its products, provide Technical Support with the following information: ❑ Model and serial number ❑ Description of the problem Refer to page viii or visit our web site at www.alliedtelesyn.com for a list of worldwide locations and contact information.
Appendix A Translated Safety and Emission Information IMPORTANT: This appendix contains multiple-language translations for the safety statements in this guide. WICHTIG: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. VIGTIGT: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. BELANGRIJK: Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids.
Translated Safety and Emission Information Standards: This product meets the following standards. U.S. Federal Communications Commission RADIATED ENERGY Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
AT-FS909SX Installation Guide ! 12 PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the equipment and shall be easily accessible. ! 13 CAUTION: Air vents must not be blocked and must have free access to the room ambient air for cooling. ! 14 OPERATING TEMPERATURE: This product is designed for a maximum ambient temperature of 40° degrees C. ! 15 ALL COUNTRIES: Install product in accordance with local and National Electrical Codes.
Translated Safety and Emission Information Standarder: Dette produkt tilfredsstiller de følgende standarder. !1 Radiofrekvens forstyrrelsesemission !2 ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. !3 Immunitet EN50082-1 !4 Elektrisk sikkerhed EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Klasse A SIKKERHED !6 ADVARSEL Laserprodukt av klasse 1.
AT-FS909SX Installation Guide Eisen: Dit product voldoet aan de volgende eisen. !1 RFI Emissie !2 WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen. !3 Immuniteit EN50082-1 !4 Electrische Veiligheid EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Klasse A VEILIGHEID !6 WAARSHUWING Klasse-1 laser produkt. !7 WAARCHUWING Neit in de straal staren.
Translated Safety and Emission Information Normes: ce produit est conforme aux normes de suivantes: !1 Emission d’interférences radioélectriques EN55022 Classe A !2 MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. !3 Immunité EN50082-1 !4 Sécurité électrique EN60950, UL1950, CSA 950 !5 Laser EN60825 SÉCURITÉ !6 ATTENTION Producit laser di classe 1.
AT-FS909SX Installation Guide Standardit: Tämä tuote on seuraavien standardien mukainen. !1 Radioaaltojen häirintä !2 VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin. !3 Kestävyys EN50082-1 !4 Sähköturvallisuus EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Luokka A TURVALLISUUS !6 VAROITUS Luokan 1 Lasertuote. !7 VARIOTUS Älä katso säteeseen.
Translated Safety and Emission Information Standard: Questo prodotto è conforme ai seguenti standard. !1 Emissione RFI (interferenza di radiofrequenza) EN55022 Classe A !2 AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti. !3 Immunità EN50082-1 !4 Sicurezza elettrica EN60950, UL1950, CSA 950 !5 Laser EN60825 NORME DI SICUREZZA !6 AVVERTENZA Prodotto laser di Classe 1.
AT-FS909SX Installation Guide Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. !1 RFI stråling !2 ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. !3 Immunitet EN50082-1 !4 Elektrisk sikkerhet EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Klasse A SIKKERHET !6 ADVARSEL Laserprodukt av klasse 1. !7 ADVARSAL Stirr ikke på strålen.
Translated Safety and Emission Information Padrões: Este produto atende aos seguintes padrões. !1 Emissão de interferência de radiofrequênciaEN55022 Classe A !2 AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas.
AT-FS909SX Installation Guide Estándares: Este producto cumple con los siguientes estándares. !1 Emisión RFI !2 ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto. !3 Inmunidad EN50082-1 !4 Seguridad eléctrica EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Clase A SEGURIDAD !6 ¡ADVERTENCIA! Producto láser Clase 1.
Translated Safety and Emission Information Standarder: Denna produkt uppfyller följande standarder. !1 Radiostörning !2 VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder !3 Immunitet EN50082-1 !4 Elsäkerhet EN60950, UL1950, CSA 950 !5 Laser EN60825 EN55022 Klass A SÄKERHET !6 VARNING! Laserprodukt av klass 1. !7 VARNING! Laserstrålning när enheten är öppen.
Appendix B Technical Specifications The sections that follow list the technical specifications for the AT-FS909SX. Physical Specifications Dimensions: (W x D x H) 330 mm x 230 mm x 43 mm (13 in x 9.05 in x 1.69 in) Weight: 2.55 kg (5.
Appendix C Technical Support Fax Order Name_________________________________________________________________ Company_____________________________________________________________ Address ______________________________________________________________ City ___________________ State/Province_______________________________ Zip/Postal Code ______________ Country_______________________________ Phone _____________________________Fax_______________________________ Incident Summary Model number of Allied Telesyn p
Appendix D AT-FS909SX Installation Guide Feedback Please tell us what additional information you would like to see discussed in this guide. If there are topics you would like information on that were not covered in this guide, please photocopy this page, answer the questions and fax or mail this form back to Allied Telesyn. The mailing address and fax number are at the bottom of the page. Your comments are valuable when we plan future revisions of this guide.
