AT-GS903SX Gigabit Switch Installation Guide PN 613-10842-00 Rev C
Copyright 2000 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA 94086 USA All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn International Corp.
Electrical Safety and Emission Compliance Statement Standards: This product meets the following standards. U.S. Federal Communications Commission RADIATED ENERGY Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Electrical Safety and Emission Compliance Statement Important: Appendix A contains translated safety statements for installing this equipment. When you see the !, go to Appendix A for the translated safety statement in your language. Wichtig: Anhang A enthält übersetzte Sicherheitshinweise für die Installation dieses Geräts. Wenn Sie ! sehen, schlagen Sie in Anhang A den übersetzten Sicherheitshinweis in Ihrer Sprache nach.
Table of Contents Electrical Safety and Emission Compliance Statement ......................iii Welcome to Allied Telesyn ......................................................................... vii Where to Find Web-based Guides ................................................................... vii Documentation Conventions............................................................................ vii Contacting Allied Teleysn ............................................................................
Appendix A Translated Safety and Emission Information ....................................... 17 Appendix B Technical Specifications ............................................................................ 29 Physical Specifications ..................................................................................... 29 Environmental Specifications .......................................................................... 29 Power Specifications ..........................................................
Welcome to Allied Telesyn The guide provides the required information to install and configure the AT-GS903SX Gigabit Ethernet Switch. Where to Find Web-based Guides Allied Telesyn wants our customers to be well informed by providing the most up-to-date and most easily accessible way to find our guides and other technical information. Visit our website at www.alliedtelesyn.com/support/lib_allproducts.htm for related product information.
Welcome to Allied Telesyn Contacting Allied Teleysn There are several ways to contact Allied Telesyn technical support, online, telephone, fax or by e-mail. Online Support You can request technical support online by filling out the Tech-Assistant Form at www.alliedtelesyn.com/forms/feedtech.htm.
AT-GS903SX Installation Guide Returning Products Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesyn without a RMA number will be returned to the sender at the sender’s expense.
Welcome to Allied Telesyn For Sales or Corporate Information Allied Telesyn International, Corp. 19800 North Creek Parkway, Suite 200 Bothell, WA 98011 Tel: 1 (425) 487-8880 Fax: 1 (425) 489-9191 Allied Telesyn International, Corp. 960 Stewart Drive, Suite B Sunnyvale, CA 94086 Tel: 1 (800) 424-4284 (USA and Canada) Fax: 1 (408) 736-0100 Tell Us What You Think In our continuing efforts to help you get the most from Allied Telesyn, we look for new and better ways to document our products.
Chapter 1 Product Description This chapter describes the features of the AT-GS903SX Gigabit Ethernet Switch. Features The AT-GS903SX is an unmanaged, Gigabit Ethernet Switch that provides familiar Ethernet technology with high-speed access. It is a high-performance switch that can be installed on the desktop, mounted on a wall, or installed in a 19-inch rack.
Product Description Physical Description Figure 1 shows the front panel of the switch. Figure 1 The AT-GS903SX Switch (Front) Figure 2 shows the rear view of the switch showing the AC input and fan locations. Figure 2 Rear View of AT-GS903SX Switch Figure 3 shows the labels for the LEDs indicators for the two types of ports.
AT-GS903SX Installation Guide LEDs Table 1 describes the switch LEDs. Refer to Figure 3 for the labels for the LEDs for the two types of ports. Table 1 AT-GS903SX LED Indicators LED Color Indicates Power Green On The switch is powered up and ready for use. Off The switch is powered off. Gigabit Ethernet Port Status LEDs Link Activity Green On Link is present; port is enabled; full-duplex operation. Off Link is not present. Green Flashing Packets are being transmitted/received on this port.
Product Description MDI Button The MDI provides you with the flexibility for using a straight-through cable to connect to a hub or another switch, or to any DTE such as an end station or a server. The button is associated with Port 4. Table 2 describes the MDI button positions.
AT-GS903SX Installation Guide AC Power Connector The switch has a single AC power supply socket in the rear panel, which has autoranging AC voltage inputs. The input voltage range is from 100-120/200-240 VAC, 50/60 Hz. The power cord acts as an ON/OFF switch. Where to Go Next Proceed to Chapter 2 for details on how to install the switch.
Chapter 2 Installation This chapter describes how to install the AT-GS903SX on a desktop, on a wall, or into a 19-inch rack. Verifying Switch Package Contents Make sure the following items are included in your switch package. If any of the following items are missing or damaged, contact your sales representative.
Installation ❑ If you are installing the switch on a desk, make sure it is placed on a level, secure desktop. ❑ Do not place objects on top of the switch. ❑ Do not expose the switch to moisture or water. ❑ Make sure it is in a dust-free environment. ❑ Use dedicated power circuits or power conditioners to supply reliable electrical power to the network devices. Note To install the switch vertically on a wall, use the AT-BRKT18 WallMount Bracket; order it from your Allied Telesyn representative.
AT-GS903SX Installation Guide Installing the Switch on a Wall The switch can be installed vertically or horizontally on the wall. Warning To install the switch vertically on a wall, you must use the accessory AT-BRKT18 Wall-Mount Bracket. DO NOT USE the keyholes in the bottom of the switch chassis to mount it vertically on the wall. These instructions are for mounting the switch horizontally on the wall.
Installation Installing the Switch in a Rack Mount Caution Do not use power tools to perform this installation. 1. Remove all cables and the power cord from the switch (if previously attached). Caution Air vents must not be blocked and must have free access to the room ambient air for cooling. ! 11 2. Attach the rackmounting brackets to each side of the switch as shown in Figure 4, using the eight flathead screws that came in the switch package.
AT-GS903SX Installation Guide 6. Connect the data cables and observe normal operation as indicated by the port LEDs. Refer to Table 1 on page 3 for LED information. For Port 4, set the MDI Button to the correct setting. Refer to Table 2 on page 4 for the MDI setting. Warranty Registration When you finish the installation, register your product by completing the enclosed warranty card and sending it in, or by visiting our web site at www.alliedtelesyn.com/forms/warranty.
Chapter 3 Troubleshooting This chapter provides information on how to detect and resolve problems with your switch. This chapter includes the following sections: ❑ How the Switch Reports Problems ❑ Network Cabling Problems ❑ Common Problems ❑ Calling Technical Support How the Switch Reports Problems The LEDs indicate problems with the ports and power. See Table 1 on page 3 for a description of the switch LEDs.
Troubleshooting Link /Activity LED on Any Port is OFF This can indicate: ❑ A loose data cable. ❑ The device at the other end of the connection is turned OFF. ❑ The data cable is not wired correctly (straight/crossed) for the device. Perform the following steps in sequence; you need not proceed to the next step if the problem is resolved: 1. Make sure the data cables are secure. 2. Make sure the device at the end of the connection is turned ON. 3.
AT-GS903SX Installation Guide Calling Technical Support When contacting Allied Telesyn for support on any of its products, provide Technical Support with the following information: ❑ Model and serial number ❑ Description of the problem Refer to page viii or visit our web site at www.alliedtelesyn.com for a list of worldwide locations.
Appendix A Translated Safety and Emission Information IMPORTANT: This appendix contains multiple-language translations for the safety statements in this guide. WICHTIG: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. VIGTIGT: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. BELANGRIJK: Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids.
Translated Safety and Emission Information Standards: This product meets the following standards. U.S. Federal Communications Commission RADIATED ENERGY Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
AT-GS903SX Installation Guide !9 ELECTRICAL - TYPE CLASS 1 EQUIPMENT THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a properly wired earth ground socket outlet. An improperly wired socket outlet could place hazardous voltages on accessible metal parts. ! 10 PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the equipment and shall be easily accessible. ! 11 CAUTION: Air vents must not be blocked and must have free access to the room ambient air for cooling.
Translated Safety and Emission Information ! 11 VORSICHT Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen freien Zugang zur Raumluft haben. ! 12 BETRIEBSTEMPERATUR: Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht mehr als 40° C entworfen. ! 13 ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen Vorschriften entsprechen. Standarder: Dette produkt tilfredsstiller de følgende standarder.
AT-GS903SX Installation Guide ! 12 BETJENINGSTEMPERATUR: Dette apparat er konstrueret til en omgivende temperatur på maksimum 40 grader C. ! 13 ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og national lovgivning for elektriske installationer. Eisen: Dit product voldoet aan de volgende eisen. !1 RFI Emissie !2 WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen.
Translated Safety and Emission Information Normes: ce produit est conforme aux normes de suivantes: !1 Emission d’interférences radioélectriques EN55022 Classe A !2 MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. !3 Immunité EN50082 - 1 !4 Sécurité électrique EN60950, UL1950, CSA 950 SÉCURITÉ !5 Ce matériel est un "PRODUIT À DIODE ÉLECTROLUMINESCENTE DE CLASSE 1”.
AT-GS903SX Installation Guide Standardit: Tämä tuote on seuraavien standardien mukainen. !1 Radioaaltojen häirintä !2 VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin. !3 Kestävyys EN50082-1 !4 Sähköturvallisuus EN60950, UL1950, CSA 950 EN55022 Luokka A TURVALLISUUS !5 Tämä on "ENSIMMÄISEN LUOKAN VALODIODITUOTE".
Translated Safety and Emission Information Standard: Questo prodotto è conforme ai seguenti standard. !1 Emissione RFI (interferenza di radiofrequenza) EN55022 Classe A !2 AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti. !3 Immunità EN50082-1 !4 Sicurezza elettrica EN60950, UL1950, CSA 950 NORME DI SICUREZZA !5 Questo è un "PRODOTTO CON LED DI CLASSE 1".
AT-GS903SX Installation Guide Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. !1 RFI stråling !2 ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. !3 Immunitet EN50082-1 !4 Elektrisk sikkerhet EN60950, UL1950, CSA 950 EN55022 Klasse A SIKKERHET !5 Dette er et "KLASSE 1 LED PRODUKT".
Translated Safety and Emission Information Padrões: Este produto atende aos seguintes padrões. !1 Emissão de interferência de radiofrequênciaEN55022 Classe A !2 AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas. !3 Imunidade EN50082-1 !4 Segurança Eléctrica EN60950, UL1950, CSA 950 SEGURANÇA !5 Este é um "PRODUTO CLASSE 1 LED".
AT-GS903SX Installation Guide Estándares: Este producto cumple con los siguientes estándares. !1 Emisión RFI !2 ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto.
Translated Safety and Emission Information Standarder: Denna produkt uppfyller följande standarder. !1 Radiostörning !2 VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. !3 Immunitet EN50082-1 !4 Elsäkerhet EN60950, UL1950, CSA 950 EN55022 Klass A SÄKERHET !5 Detta är en "KLASS 1 LYSDIODPRODUKT".
Appendix B Technical Specifications Physical Specifications Dimensions (W x D x H): 341 mm x 231 mm x 43 mm (13.3 in x 9 in x 1.69 in) Weight: 2.3 kg (5.
Appendix C Technical Support Fax Order Name_________________________________________________________________ Company_____________________________________________________________ Address ______________________________________________________________ City ___________________ State/Province_______________________________ Zip/Postal Code ______________ Country_______________________________ Phone _____________________________Fax_______________________________ Incident Summary Model number of Allied Telesyn p
Appendix D AT-GS903SX Installation Guide Feedback Please tell us what additional information you would like to see discussed in this guide. If there are topics you would like information on that were not covered in this guide, please photocopy this page, answer the questions and fax or mail this form back to Allied Telesyn. The mailing address and fax number are at the bottom of the page. Your comments are valuable when we plan future revisions of this guide.
