AR750S-DP Secure VPN Router Installation and Safety Guide AR750S-DP AT-PWR03
AR750S-DP Router Installation and Safety Guide AR750S-DP Secure VPN Router AT-PWR03 AC Power Supply AT-PWR03 DC Power Supply
AR750S-DP Secure VPN Router AR750S-DP Router Installation and Safety Guide Document Number 613-000532 Rev C. © 2011 Allied Telesis Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis Inc. Allied Telesis Inc. reserves the right to change specifications and other information in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis Inc.
Installation and Safety Guide Table of Contents Models Covered By This Guide .................................................................................... 4 Package Contents ............................................................................................................. 4 Installing the Router ......................................................................................................... 5 Installing the Router in a Rack ........................................................
AR750S-DP Secure VPN Router Models Covered By This Guide This Installation and Safety Guide includes information on these models: ■ AR750S-DP Secure VPN Router ■ AT-PWR03 DC power supply ■ AT-PWR03 AC power supply Documentation updates can be found at www.alliedtelesis.com/support/documentation/ Package Contents Before beginning any installation, please check the package contents. Contact your authorised Allied Telesis distributor or reseller if any items are damaged or missing.
Installation and Safety Guide AT-PWR03 AC PSU package contents These items are included for each AC power supply: ■ one AT-PWR03 AC power supply ■ A set of AC power cords One of these is suitable for your region. If desired, you can return the extra cords to your authorised Allied Telesis distributor or reseller.
AR750S-DP Secure VPN Router Before installing ■ Unpack the router and verify the package contents. If any items are damaged or missing, contact your sales representative. ■ If you have purchased any Port Interface Cards (PICs), you will need the PIC and PIC Quick Install Guide. Read “Installing PICs” on page 6 for further details. ■ Read the safety information “Safety” on page 25.
Installation and Safety Guide Installing the Router in a Rack 1. Check the rack. • Ensure that the rack is safely secured and that it will not tip over. Devices in a rack should be installed starting at the bottom, with the heavier devices near the bottom of the rack. • Ensure the rack has sufficient space for the router and its associated cables. The router is 1U high. 2. Unscrew the feet from the router, if you have previously attached them. 3.
AR750S-DP Secure VPN Router Installing the Router on a Level Surface 1. Check the level surface. Ensure it has sufficient space for the router and its associated cables. 2. Screw the rubber feet provided into the correct holes on the underside of the router. This will stop the router from slipping, and protect the level surface from scratches.
Installation and Safety Guide Using an AT-PWR03 Power Supply (PSU) Warning All AC and DC versions of this equipment must be earthed. Warning The maximum power supply requirements for the AR750S-DP are clearly displayed on the rear of each AT-PWR03 power supply. If the supply is outside the accepted range, the router may not operate, or damage to the router or PSU may result. Use only AT-PWR03 power supplies to power an AR750S-DP Router.
AR750S-DP Secure VPN Router Installing the Power Supply Before installing a power supply: ■ gather the necessary tools and equipment ■ read the section “Using an AT-PWR03 Power Supply (PSU)” on page 9 1. Unpack the power supply unit. Caution Follow correct anti-static procedures when installing a PSU. Failure to do so could damage the PSU or router. If you are unsure about correct procedures, contact your authorised Allied Telesis distributor or reseller.
Installation and Safety Guide Top of Router PSU (DC) Captive screw Captive screw PSU Insert Firmly press the PSU until the faceplate engages, or nearly engages, the chassis. 5. Secure the power supply unit. Use a Phillips #2 screwdriver to tighten the two captive Phillips screws on the faceplate of the PSU.
AR750S-DP Secure VPN Router 1. Check that the power supply and cable is not live. Ensure the circuit breaker for the supply circuit is in the off position, and the PSU run/standby button is in the standby position. When the run/standby button is not depressed, it is in standby. 2. Plug the supply cable into the router. Plug the provided DC power cord into the power inlet on the faceplate of the PSU. The plug is keyed with locking tabs, and will only fit in the inlet one way.
Installation and Safety Guide 4. Connect the cable to the circuit breaker. Connect the supply cable wires to the circuit breaker, in accordance with the applicable wiring regulations in your region, and in conjunction with any safety guide information for the DC supply unit. Ensure there are no exposed cable strands. The correct wire colour for each polarity is: • blue: negative • black: earth • red: positive Caution Check that the supply cable wires are wired to the correct polarity.
AR750S-DP Secure VPN Router Removing a Power Supply Before removing a PSU from the router: ■ gather the necessary tools and equipment ■ read the section “Using an AT-PWR03 Power Supply (PSU)” on page 9 Warning Disconnect the power cord before removing the PSU. 1. Disconnect the power to the PSU. For AC models, turn off the main power supply to the PSU and disconnect the power cord. For DC models, push the run/standby button on the back of the PSU, so that the PSU is in the standby position.
Installation and Safety Guide Configuring the Router The AR750S-DP comes with a simple default configuration (“AR750S-DP Default Configuration” on page 20).
AR750S-DP Secure VPN Router • To connect via a LAN, use an Ethernet cable to connect the router’s switch port(s) to the device(s) on the LAN. Select the LAN PC from which you wish to configure the router. The PC should be in the same subnet as the part of the LAN that contains the router (for example, the PC could be connected to a hub or Layer 2 switch that is directly connected to one of the router’s switch ports).
Installation and Safety Guide Caution As a security precaution, change the password as soon as possible. Remember the new password, as there is no way to retrieve it if it is lost. To change the password, select Management > Users from the sidebar menu. Select the Manager account and click Modify. 5. Customise the router for your region. Change the default ISDN territory to your region.
AR750S-DP Secure VPN Router Configure with the Command Line Interface (CLI) Caution If another device on your network already uses the router’s default IP address, 192.168.1.1, do not connect the AR750S-DP to the network until you have changed the IP address of the router’s default VLAN using the CLI. 1. Initiate router start-up.
Installation and Safety Guide 2. Log in and set the password. The login prompt appears on the terminal or PC. If the login prompt does not appear, press [Enter] two or three times. When the router boots for the first time it automatically creates an account with manager privileges. The account has the login name “manager” and the password is “friend”. Passwords are case sensitive. At the login prompt, enter the login name and password.
AR750S-DP Secure VPN Router 5. Use the CLI to continue configuring the router. See the AR700 Series Router Software Reference for details about commands available for configuring the router (including a list of message definitions). To display a list of help topics, enter: help To display help on a specific topic, enter: help topic Alternatively, type a question mark (?) at the end of a partially completed command to see a list of valid options.
Installation and Safety Guide Connecting Data Cables to the AR750S-DP Connecting the router to your network 1. Connecting to the LAN: If you have not already done so, use Ethernet patch cables to connect the devices on your private network (LAN) to the router’s switch ports. By default, all switch ports are members of VLAN1. 2.
AR750S-DP Secure VPN Router LEDs on the AR750S-DP The front panel of the router has LEDs that indicate the operational status of the router, its switch and ethernet ports, and any connected power supply or PIC card. Further details about the router’s operations can be found using the CLI command show system. LED State Function Status PSU1..2 Green The router is ON, and is receiving power from the PSU as indicated by the LED. Amber There is a fan or power fault. Off Normal operation.
Installation and Safety Guide LED State Function Switch Ports 1..5 Green The switch port has a 100 Mbps link. Amber The switch port has a 10 Mbps link. Flashing Data is being transmitted or received on the switch port. Green The switch port is operating at full duplex. Amber The switch port is operating at half duplex. Amber flashing There is a collision on the switch port. Green A port interface card (PIC) is correctly installed and has been detected by the router. L/A Switch Ports 1..
AR750S-DP Secure VPN Router Emission Compliance Statements STANDARDS: The AR750S-DP Routers meet the following standards: Category Approval Agency and Requirement Safety UL60950-1 CAN/CSA-C22.2 No. 60950-1-03 EN60950-1 AS/NZS 60950.
Installation and Safety Guide Safety WARNING: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. ELECTRICAL NOTICES WARNING: ELECTRIC SHOCK HAZARD To prevent ELECTRIC shock, do not remove the cover. No user-serviceable parts inside. This unit contains HAZARDOUS VOLTAGES and should only be opened by a trained and qualified technician.
AR750S-DP Secure VPN Router WARNING: For centralized DC power connection, install only in a restricted access area. A tray cable is required to connect the power source if the unit is powered by centralized DC power. The tray cable must be UL listed Type TC tray cable and rated at 600 V and 90 degrees C, with three conductors, minimum 14 AWG. WARNING: Only trained and qualified personnel are allowed to install or replace this equipment.
Installation and Safety Guide VORSICHT: DAS NETZKABEL DIENT ZUM TRENNEN DER STROMVERSORGUNG. ZUR TRENNUNG VOM NETZ, KABEL AUS DER STECKDOSE ZIEHEN. GERÄTE DER KLASSE 1 DIESE GERÄTE MÜSSEN GEERDET SEIN. Der Netzstecker darf nur mit einer vorschriftsmäßig geerdeten Steckdose verbunden werden. Ein unvorschriftsmäßiger Anschluß kann die Metallteile des Gehauses unter gefährliche elektrische Spannungen setzen.
AR750S-DP Secure VPN Router Warnung: Aus Sicherheitsgründen sollte am Netzteilende des mit dieser LANEinrichtung verwendeten Kabels ein 15-Ampere-Leistungsschalter installiert werden. Nehmen Sie STETS zuerst die Verkabelung der LAN-Einrichtung vor, bevor Sie die Kabel an den Leistungsschalter anschließen. Arbeiten Sie nie mit SPANNUNGSFÜHRENDEN Kabeln, um Körperverletzungen durch Stromschlag zu vermeiden.
Installation and Safety Guide ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE STRØMMEN. SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen ud af stikket. ELEKTRISK - KLASSE 1-UDSTYR DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet med en korrekt installeret jordforbunden stikkontakt. En ukorrekt installeret stikkontakt kan sætte livsfarlig spænding til tilgængelige metaldele. UDSTYR TIL STIKKONTAKT, stikkontakten bør installeres nær ved udstyret og skal være lettilgængelig.
AR750S-DP Secure VPN Router Advarsel: Man bør ikke afisolere mere af ledningerne end anvist, for så kan sådanne blanke ledninger udgøre et faremoment efter montering på klemmerækken. Advarsel: Ved installering af dette udstyr skal steljord altid forbindes først og aftages sidst. Advarsel: “Fare” Se omhyggeligt efter om der stikker blanke kobbertråde ud fra klemmeforbindelserne. Ved korrekt montering er det ikke tilfældet.
Installation and Safety Guide ELEKTRISCH: OVERBELASTING VAN WISSELSTROOM HOOFDCIRCUIT Tijdens de installatie van het produkt dient men rekening te houden met de gecombineerde waarden op de naamplaatjes bij het aansluiten van het toestel op de wisselstroom-voedingsdraden. LOPGELET: MECHANISCH LADEN - De montage van het toestel in het rek dient zo uitgevoerd te worden dat geen gevaar ontstaat door een ongelijke lading. Lithium batterij.
AR750S-DP Secure VPN Router Waarschuwing: “Veiligheidsrisico” Controleer of er bij de aangesloten bedrading geen koper blootligt. Als de installatie juist is uitgevoerd, is er bij het aansluitblok geen koperdraad zichtbaar. Blootliggende bedrading kan schadelijke elektriciteitsniveaus geleiden naar personen die met de draden in aanraking komen. Opmerking: Dit systeem werkt met positief geaarde of negatief geaarde DCsystemen.
Installation and Safety Guide SURCHARGE DES CIRCUITS PRINCIPAUX DE COURANT ALTERNATIF ÉLECTRIQUE Lors de l'installation du matériel, il faut prendre en compte la somme des puissances indiquées sur les étiquettes au moment de connecter le matériel à une source de courant alternatif. ATTENTION : RÉPARTITION DE LA CHARGE MÉCANIQUE - Le montage du matériel dans le bâti doit être effectué de telle manière que la répartition de la charge mécanique ne pose aucun danger.
AR750S-DP Secure VPN Router Avertissement: “Risque de sécurité” Vérifiez qu’aucun fil de cuivre dénudé ne sort du câble installé. Lorsque cette installation est effectuée correctement, aucun fil de cuivre ne devrait dépasser du bornier. Tout câblage dénudé peut être conducteur de tensions dangereuses pour les personnes touchant les câbles. Remarque: Ce système peut fonctionner avec des systèmes C.C. dotés d’une mise à la terre positive ou négative.
Installation and Safety Guide Litiumparisto - Vaihdon voi suorittaa vain koulutettu ja pätevä teknikko. Varoitus: Räjähdysvaara, jos paristo on vaihdettu väärin. Vaihda vain samaan tai vastaavaan tyyppiin, jota valmistaja suosittelee. Hävitä käytetyt paristot valmistajan ohjeiden mukaan. KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten sähköturvallisuusmääräysten mukaisesti. Varoitus: KESKITETTY TASAVIRTAKYTKENTÄ ASENNETTAVA AINOASTAAN TILAAN, JOHON ON RAJOITETTU PÄÄSY.
AR750S-DP Secure VPN Router Norme di Sicurezza AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti. AVVERTENZE ELETTRICHE ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le componenti interne non sono riparabili dall’utente. Questa unità ha TENSIONI PERICOLOSE e va aperta solamente da un tecnico specializzato e qualificato.
Installation and Safety Guide TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative elettriche nazionali. Avvertenza: AI FINI DEL COLLEGAMENTO CENTRALIZZATO DI ALIMENTAZIONE A CC, INSTALLARE SOLO IN UN’AREA AD ACCESSO LIMITATO.
AR750S-DP Secure VPN Router Sikkerhet ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. ELEKTRISITET ADVARSEL: FARE FOR ELEKTRISK SJOKK For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som brukeren kan reparere på innsiden. Denne enheten inneholder FARLIGE SPENNINGER, og må kun åpnes av en faglig kvalifisert tekniker.
Installation and Safety Guide Merknad: En kanalkabel er nødvendig for å kople til strømkilden hvis enheten drives av strøm fra et likestrømsnett. Kanalkabelen må være utstyrt med ULmerke med type TC, normert for 600 V og 90 ºC med tre ledere som har en tykkelse på minst 12AWG (amerikansk ledningsmål). Advarsel: DETTE UTSTYRET SKAL BARE MONTERES ELLER SKIFTES UT AV KVALIFISERT PERSONELL SOM HAR GJENNOMGÅTT OPPLÆRING.
AR750S-DP Secure VPN Router Segurança AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas. AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS ATENÇÃO: PERIGO DE CHOQUE ELÉTRICO Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças que possam ser consertadas pelo usuário. Este aparelho contém VOLTAGENS PERIGOSAS e só deve ser aberto por um técnico qualificado e treinado.
Installation and Safety Guide TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e locais para instalações elétricas. Aviso: PARA UMA LIGAÇÃO CC CENTRALIZADA, INSTALE APENAS NUMA ZONA DE ACESSO RESTRITO. Nota: É necessário um cabo de bandeja para ligar a fonte de energia se a unidade for alimentada por um fonte CC centralizada. O cabo de bandeja deve fazer parte da lista UL do Tipo TC cabo de bandeja para 600 V e 90 graus C, com três condutores, com um mínimo de 14 AWG.
AR750S-DP Secure VPN Router Seguridad ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto. AVISOS ELECTRICOS ADVERTENCIA: PELIGRO DE ELECTROCHOQUE Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún componente en el interior al cual puede prestar servicio el usuario. Esta unidad contiene VOLTAJES PELIGROSOS y sólo deberá abrirla un técnico entrenado y calificado.
Installation and Safety Guide Batería de litio - Sólo deberá ser cambiada por un técnico entrenado y calificado. ATENCION: Peligro de explosión si la batería no se reemplaza en forma correcta. Reemplace sólo con el mismo tipo o equivalente que recomienda el fabricante. Deseche las baterías usadas según las instrucciones del fabricante. PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos Eléctricos locales y nacionales.
AR750S-DP Secure VPN Router Säkerhet VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK: RISK FÖR ELEKTRISK STÖTFör att undvika ELEKTRISK stöt, ta ej av locket. Det finns inga delar inuti som behöver underhållas. Denna apparat är under HÖGSPÄNNING och får endast öppnas av en utbildad kvalificerad tekniker.
Installation and Safety Guide Anmärkning: Kanalkabel krävs för att ansluta strömkällan om enheten ansluts till likströmsnät. Kanalkabeln måste vara UL-märkt och av TC-typ. Kabeln måste ha en märkspänning på 600 V och en märktemperatur på 90 grader Celsius samt ha tre ledare med en tjocklek på minst 14 AWG (amerikanskt ledningsmått). Varning: INSTALLATION OCH UTBYTE AV DENNA UTRUSTNING FÅR ENDAST UTFÖRAS AV AUKTORISERAD ELINSTALLATÖR.
AR750S-DP Secure VPN Router Connection to mains voltage supply Each PSU is supplied with a power cord that has been approved for use. The PSU must only use the supplied power cord. In the event that you require a replacement power cord, contact your authorised Allied Telesis distributor or reseller. For continued protection against the risk of fire and shock hazard, replace fuses only with the same type and rating. Telecommunications Interfaces Warning To reduce risk of fire use only No.
Installation and Safety Guide Connection to ISDN network Ports for the connection of other apparatus The following interfaces normally operate at SELV (Safe Extra Low Voltage) levels: ■ Asynchronous (console) ports ■ Ethernet ports ■ G703 ports ■ Synchronous ports Note SELV is a secondary circuit whose voltages do not exceed a safe value under normal operating conditions and under single fault conditions. Under normal operating conditions the voltages do not exceed 42.4 V peak AC or 60 V DC.
AR750S-DP Secure VPN Router US Federal Communications Commission (FCC) This equipment complies with Part 68 of the Federal Communications Commission (FCC) rules for the United States. A label is located on the underside of the base unit containing the FCC registration number. You must, upon request, provide the following information to your local telephone company: For the AR021U PIC Facility Interface Code 021S5 Service Order Code 6.
Installation and Safety Guide Canadian Department of Communications The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
