AT-PWR3202 Power Supply Installation Guide

*613-000397 Rev B*
PN 613-000397 Rev. B 1 2 3
AT-PWR3202 Power Supply Installation Guide
Overview
AT-PWR3202 Power Supply is designed to be installed in an AT-RPS3204
Redundant Power Supply (RPS). The RPS can supply power to Allied Telesis
switches if the switch’s main power supply fails
.
Verifying Package Contents
Verify that the correct components are included in your package:
• AT-PWR3202 Power Supply
• One 21-pin D-combo connector cable
• This installation guide
If any item is missing or damaged, contact your Allied Telesis sales
representative for assistance.
Warranty
The AT-PWR3202 Power Supply has a Lifetime Year Warranty (Five Years
Power Supply and Fan). For detailed warranty information, see the
www.alliedtelesis.com website.
Installing the Power Supply
To install an AT-PWR3202 Power Supply, perform the following procedure:
1. Remove the AT-PWR3202 unit from its shipping package and store the
package in a safe place. You must use the original package if you need to
return the power supply to Allied Telesis.
2. On the back of the AT-RPS3204 unit, locate the power switch that
corresponds to the slot where you are going to install the power supply and
verify that the On/Off button is in the Off (out) position. From left to right on
the back, the power supplies are identified as B2, B1, A2, A1. (An AT-
RPS3204 is shipped with one AT-PWR3202 in the slot marked A1.)
3. Using a Phillips head screwdriver, remove the cover from the slot in the front
of the AT-RPS3204 unit where you want to install the power supply.
Note
As an example, the following steps show an AT-PWR3202 unit installed in
slot A2 of the AT-RPS3204 Redundant Power Supply.
Keep the slot cover in a safe area in case you remove a power supply. The
slot cover helps maintain proper air flow through the RPS.
4. Slide the AT-PWR3202 Power Supply into the slot
5. Use a Phillips head screwdriver to tighten the captive screws.
6. On the back of the AT-RPS3204 unit, plug one end of the 21-pin D-combo
connector cable into the connector that corresponds to the slot in which you
installed the AT-RPS3202 Power Supply.
7.
Tighten the captive screws.
892
STA
TU
S
POWER
FAULT
AT-PW
R3202
12V
D
C
,1
6
.
6A MAX
STATUS
POWER
F
AUL
T
STATUS
POW
E
R
F
AULT
893
AT-PW
R320
2
12VDC ,16.6A MAX
STATUS
POWER
FAULT
STATUS
POWER
FAULT
894
S
TA
T
U
S
POWER
FAULT
AT-PW
R320
2
12VD
C
,16.6A
M
A
X
AT-PW
R
320
2
12VD
C
,16
.6A
M
A
X
STATUS
POW
ER
FAULT
STATUS
POWER
FAULT
895
STATUS
POWER
FAULT
AT
-P
W
R3202
12VD
C
,16.6A MA
X
AT-PWR3202
12VD
C ,16.6A MA
X
198
RPS O
U
TPU
T A2
12VDC
R
PS O
UTPU
T A
1
12VDC
AC INPUT A
2/A
1
100 - 240 VAC
~
O
N
O
F
F
O
N
O
F
F
A1
A2
199
RPS OUTPU
T A2
12VDC
RPS OUTPUT A1
12VDC
AC INPUT A2/A
1
100 - 240 VAC
~
ON
OFF
O
N
OFF
A1
A2