Manual
Table Of Contents
- Table of Contents
- List of Figures
- Preface
- Chapter 1
- Overview
- Section I
- Basic Operations
- Chapter 2
- Starting a Local or Telnet Management Session
- Chapter 3
- Enhanced Stacking
- Chapter 4
- Basic Switch Parameters
- When Does a Switch Need an IP Address?
- Configuring an IP Address and Switch Name
- Activating the BOOTP and DHCP Client Software
- Rebooting a Switch
- Configuring the Manager and Operator Passwords
- Setting the System Time
- Configuring the Console Startup Mode
- Configuring the Console Timer
- Enabling or Disabling the Telnet Server
- Setting the Baud Rate of the RS-232 Terminal Port
- Pinging a Remote System
- Returning the AT-S62 Software to the Factory Default Values
- Viewing System Hardware and Software Information
- Setting the Switch’s Temperature Threshold
- Chapter 5
- SNMPv1 and SNMPv2c Configuration
- Chapter 6
- Port Parameters
- Chapter 7
- MAC Address Table
- Chapter 8
- Port Trunking
- Chapter 9
- Port Mirroring
- Chapter 10
- Ethernet Statistics
- Section II
- Advanced Operations
- Chapter 11
- File System
- Chapter 12
- File Downloads and Uploads
- Chapter 13
- Event Log
- Chapter 14
- Quality of Service
- Chapter 15
- IGMP Snooping
- Chapter 16
- Denial of Service Defense
- Section III
- SNMPv3 Operations
- Chapter 17
- SNMPv3 Configuration
- SNMPv3 Overview
- Configuring the SNMPv3 Protocol
- Configuring the SNMPv3 User Table
- Configuring the SNMPv3 View Table
- Configuring the SNMPv3 Access Table
- Configuring the SNMPv3 SecurityToGroup Table
- Configuring the SNMPv3 Notify Table
- Configuring the SNMPv3 Target Address Table
- Configuring the SNMPv3 Target Parameters Table
- Configuring the SNMPv3 Community Table
- Displaying SNMPv3 Table Menus
- Displaying the Display SNMPv3 User Table Menu
- Displaying the Display SNMPv3 View Table Menu
- Displaying the Display SNMPv3 Access Table Menu
- Displaying the Display SNMPv3 SecurityToGroup Table Menu
- Displaying the Display SNMPv3 Notify Table Menu
- Displaying the Display SNMPv3 Target Address Table Menu
- Displaying the Display SNMPv3 Target Parameters Table Menu
- Displaying the Display SNMPv3 Community Table Menu
- Section IV
- Spanning Tree Protocols
- Chapter 18
- Spanning Tree and Rapid Spanning Tree Protocols
- Chapter 19
- Multiple Spanning Tree Protocol
- Section V
- Virtual LANs
- Chapter 20
- Tagged and Port-based Virtual LANs
- VLAN Overview
- Port-based VLAN Overview
- Tagged VLAN Overview
- Creating a Port-based or Tagged VLAN
- Example of Creating a Port-based VLAN
- Example of Creating a Tagged VLAN
- Modifying a VLAN
- Displaying VLANs
- Deleting a VLAN
- Deleting All VLANs
- Displaying PVIDs and Port Priorities
- Enabling or Disabling Ingress Filtering
- Specifying a Management VLAN
- Chapter 21
- GARP VLAN Registration Protocol
- Chapter 22
- Multiple VLAN Modes
- Section VI
- Port Security
- Section VII
- Management Security
- Chapter 25
- Web Server
- Chapter 26
- Encryption Keys
- Chapter 27
- Public Key Infrastructure Certificates
- Chapter 28
- Secure Shell (SSH) Protocol
- Chapter 29
- RADIUS and TACACS+ Authentication Protocols
- Chapter 30
- Management Access Control List
- Section VIII
- Web Browser Management
- Chapter 31
- Starting a Web Browser Management Session
- Chapter 32
- Enhanced Stacking
- Chapter 33
- Basic Switch Parameters
- Chapter 34
- SNMPv1 and SNMPv2c Community Strings
- Chapter 35
- Port Parameters
- Chapter 36
- MAC Address Table
- Chapter 37
- Port Trunking
- Chapter 38
- Port Mirroring
- Chapter 39
- File Downloads and Uploads
- Chapter 40
- Event Log
- Chapter 41
- Quality of Service
- Chapter 42
- IGMP Snooping
- Chapter 43
- Denial of Service Defense
- Chapter 44
- SNMPv3 Protocol
- Configuring the SNMPv3 Protocol
- Enabling the SNMP Protocol
- Configuring the SNMPv3 User Table
- Configuring the SNMPv3 View Table
- Configuring the SNMPv3 Access Table
- Configuring the SNMPv3 SecurityToGroup Table
- Configuring the SNMPv3 Notify Table
- Configuring the SNMPv3 Target Address Table
- Configuring the SNMPv3 Target Parameters Table
- Configuring the SNMPv3 Community Table
- Displaying SNMPv3 Tables
- Chapter 45
- STP, RSTP, and MSTP
- Chapter 46
- Virtual LANs
- Chapter 47
- GARP VLAN Registration Protocol
- Chapter 48
- MAC Address Security
- Chapter 49
- 802.1x Port-based Access Control
- Chapter 50
- Secure Shell Protocol
- Chapter 51
- Encryption Keys, PKI, and SSL
- Chapter 52
- RADIUS and TACACS+ Authentication Protocols
- Chapter 53
- Management Access Control List
- Appendix A
- AT-S62 Default Settings
- Basic Switch Default Settings
- Enhanced Stacking Default Setting
- SNMP Default Settings
- Port Configuration Default Settings
- Event Log Default Settings
- Quality of Service
- IGMP Snooping Default Settings
- Denial of Service Prevention Default Settings
- STP, RSTP, and MSTP Default Settings
- VLAN Default Settings
- GVRP Default Settings
- MAC Address Security Default Settings
- 802.1x Port-Based Network Access Control Default Settings
- Web Server Default Settings
- SSL Default Settings
- PKI Default Settings
- SSH Default Settings
- Server-Based Authentication Default Settings
- Management Access Control List Default Setting
- AT-S62 Default Settings
- Appendix B
- Index

AT-S62 User’s Guide
Section II: Advanced Operations 151
The following prompt is displayed:
Enter the file name (or None):
5. Enter a file name for the new configuration file.
The file name can be up to 16 alphanumeric characters. Spaces are
allowed. The filename must include the extension “.cfg”. See File
Naming Conventions on page 148.
Note
If the filename already exists, the system displays a message asking
if you want to overwrite the existing file.
Note
You cannot name a configuration file “default.cfg.” This file name is
reserved by the switch.
The management software create the new configuration file and
stores it in the file system. The file contains the current switch
configuration.
6. Type 1 to select Boot Configuration File.
The following prompt is displayed:
Enter the file name:
7. Enter the same file name that you entered in Step 5.
This makes your new configuration file the active file on the
switch. Any changes you now make to the switch’s parameter
settings are saved to this file.
The file name will now appear following selection 1 in the File
Operations menu. The file name should be followed by “Exist”,
meaning that the file exists in the switch’s file system. If “Not
Found” appears instead, you probably enter the name incorrectly,
in which case you need to repeat Steps 6 and 7.
Phase 2: Configuring the Switch’s Parameter Settings
Now that you have created a configuration file and designated it as the
active boot configuration file on the switch, you can now configure the
switch’s parameter settings by making those changes that you want the
new configuration file to contain. Once you have done that, be sure to
save your changes to the configuration file by returning to the Main
Menu and typing S to select Save Configuration Changes. Failure to save
your changes will mean that the configuration file will not contain the
new parameter settings.