User guide
Table Of Contents
- Contents
- Figures
- Tables
- Preface
- Section I
- Basic Operations
- Chapter 1
- Basic Switch Parameters
- Configuring the Switch’s Name, Location, and Contact
- Changing the Manager and Operator Passwords
- Setting the System Date and Time
- Rebooting a Switch
- Pinging a Remote System
- Returning the AT-S63 Management Software to the Factory Default Values
- Displaying the IP Address of the Local Interface
- Displaying System Information
- Chapter 2
- Port Parameters
- Chapter 3
- Enhanced Stacking
- Chapter 4
- SNMPv1 and SNMPv2c
- Chapter 5
- MAC Address Table
- Chapter 6
- Static Port Trunks
- Chapter 7
- Port Mirroring
- Section II
- Advanced Operations
- Chapter 8
- File System
- Chapter 9
- File Downloads and Uploads
- Chapter 10
- Event Logs and Syslog Client
- Chapter 11
- Classifiers
- Chapter 12
- Access Control Lists
- Chapter 13
- Class of Service
- Chapter 14
- Quality of Service
- Chapter 15
- Denial of Service Defenses
- Chapter 16
- IGMP Snooping
- Section III
- SNMPv3
- Chapter 17
- SNMPv3
- Configuring the SNMPv3 Protocol
- Enabling or Disabling SNMP Management
- Configuring the SNMPv3 User Table
- Configuring the SNMPv3 View Table
- Configuring the SNMPv3 Access Table
- Configuring the SNMPv3 SecurityToGroup Table
- Configuring the SNMPv3 Notify Table
- Configuring the SNMPv3 Target Address Table
- Configuring the SNMPv3 Target Parameters Table
- Configuring the SNMPv3 Community Table
- Displaying SNMPv3 Tables
- Section IV
- Spanning Tree Protocols
- Chapter 18
- Spanning Tree and Rapid Spanning Tree Protocols
- Chapter 19
- Multiple Spanning Tree Protocol
- Section V
- Virtual LANs
- Chapter 20
- Port-based and Tagged VLANs
- Chapter 21
- GARP VLAN Registration Protocol
- Section VI
- Port Security
- Chapter 22
- MAC Address-based Port Security
- Chapter 23
- 802.1x Port-based Network Access Control
- Section VII
- Management Security
- Chapter 24
- Encryption Keys, PKI, and SSL
- Chapter 25
- Secure Shell (SSH)
- Chapter 26
- TACACS+ and RADIUS Protocols
- Chapter 27
- Management Access Control List
- Index
AT-S63 Management Software Web Browser User’s Guide
Section I: Basic Operations 39
Displaying the IP Address of the Local Interface
This procedure displays the IP address and subnet mask of the local
interface on the switch. The local interface is used for enhanced stacking
and remote management of the switch with a Telnet or SSH client, or a
web browser. You cannot configure the local interface from the web
browser interface, For that, you must use the menus interface or the
command line interface.
To view the IP address and subnet mask of the local interface, perform the
following procedure:
1. From the home page, select Configuration.
The System page is displayed with the General tab selected by
default, as shown in Figure 1 on page 28. This procedure discusses
the parameters in the IP Configuration section of the web page.
Obtain IP Address from:
The options in this section indicate the source of the IP address of the
local interface. If DHCP or BOOTP is checked, the interface obtained
its IP address from a DHCP or BOOTP server on the network. If Static
is checked, the IP address was set manually.
IP Address
This parameter displays the IP address of the local management
interface. This address is either manually assigned to the interface or
obtained from a DHCP or BOOTP server.
Subnet Mask
This parameter specifies the subnet mask for the interface.
The IP address and subnet mask fields will be empty if no interface
has been designated as the local interface.
Default Gateway
For AT-9400 Switches that support IPv4 routing, such as the
AT-9424Ts and AT-9448Ts/XP switches, this field displays the IP
address of the next hop of the switch’s default route. The switch uses
the default route when it receives a network packet for routing, but
cannot find a route for it in the routing table. This field will contain
0.0.0.0 if no default route is defined on the switch.
For AT-9400 Switches that do not support IPv4 packet routing, such as
the AT-9424T/GB and AT-9424T/SP switches, this field displays the
default gateway address. This is the IP address of a router interface on
your network. The switch’s management software uses this address as
the next hop to reaching a remote network device, such as a remote
management workstation or a syslog server, when the switch’s local
interface and the remote device are on different subnets. The default
value is 0.0.0.0.