User Manual

ManualsBrandsAllied Telesis ManualsComputer HardwareAT-S63

Table Of Contents

Contents
Figures
Tables
Preface
- How This Guide is Organized
- Product Documentation
- Where to Go First
- Starting a Management Session
- Document Conventions
- Contacting Allied Telesis
Section I
Basic Operations
Chapter 1
Basic Switch Parameters
- Configuring the Stack’s Name, Location, and Contact
- Changing the Manager or Operator Password
- Setting the System Date and Time
- Resetting a Stack
- Pinging a Remote System
- Restoring the Factory Default Values
- Displaying the IP Address of the Local Interface
- Displaying System Information
Chapter 2
Port Parameters
- Configuring the Port Parameters
- Displaying the Port Parameters and Statistics
- Restoring the Default Settings on the Ports
Chapter 3
SNMPv1 and SNMPv2c
- Enabling or Disabling SNMP Management
- Creating New SNMPv1 and SNMPv2c Community Strings
- Modifying SNMPv1 and SNMPv2c Communities
- Deleting SNMPv1 and SNMPv2c Community Strings
- Displaying the SNMPv1 and SNMPv2c Community Strings
Chapter 4
MAC Address Table
- Displaying the MAC Address Table
- Adding Static Unicast or Multicast MAC Addresses
- Deleting Unicast or Multicast MAC Addresses
- Deleting All Dynamic MAC Addresses
- Changing the Aging Time
Chapter 5
Static Port Trunks
- Creating Static Port Trunks
- Modifying Static Port Trunks
- Deleting Static Port Trunks
- Displaying Static Port Trunks
Chapter 6
Port Mirroring
- Overview
- Creating the Port Mirror
- Modifying the Port Mirror
- Disabling the Port Mirror
- Deleting the Port Mirror
- Displaying the Port Mirror
Section II
Advanced Operations
Chapter 7
File System
- Listing the Files in Flash Memory or on a Compact Flash Card
- Selecting the Active Boot Configuration File
Chapter 8
File Downloads and Uploads
- General Guidelines
- Downloading a Master Configuration File
- Uploading a Configuration File or an Event Log File
Chapter 9
Event Logs and the Syslog Client
- Enabling or Disabling the Event Logs
- Displaying the Event Messages
- Clearing an Event Log
- Modifying an Event Log’s Full Action
- Saving an Event Log to a File
- Configuring Syslog Output Definitions
- Modifying Syslog Output Definitions
- Deleting Syslog Output Definitions
Chapter 10
IGMP Snooping
- Configuring IGMP Snooping
- Displaying the Host Nodes and the Multicast Routers
Section III
SNMPv3
Chapter 11
SNMPv3
- Configuring the SNMPv3 Protocol
- Enabling or Disabling SNMP Management
- Configuring the SNMPv3 User Table
- Configuring the SNMPv3 View Table
- Configuring the SNMPv3 Access Table
- Configuring the SNMPv3 SecurityToGroup Table
- Configuring the SNMPv3 Notify Table
- Configuring the SNMPv3 Target Address Table
- Configuring the SNMPv3 Target Parameters Table
- Configuring the SNMPv3 Community Table
- Displaying the SNMPv3 Tables
Section IV
Spanning Tree Protocols
Chapter 12
Spanning Tree and Rapid Spanning Tree Protocols
- Enabling or Disabling a Spanning Tree Protocol
- Configuring STP
- Configuring RSTP
Section V
Virtual LANs
Chapter 13
Port-based and Tagged VLANs
- Creating New Port-Based or Tagged VLANs
- Adding or Removing VLAN Ports
- Deleting VLANs
- Displaying VLANs
Section VI
Port Security
Chapter 14
802.1x Port-based Network Access Control
- Setting the Port Roles
- Enabling or Disabling 802.1x Port-based Network Access Control
- Configuring the Authenticator Port Parameters
- Configuring the Supplicant Port Parameters
- Displaying the Port Parameters and Port Status
- Configuring RADIUS Accounting
- Displaying the RADIUS Accounting Settings
Index
- Numerics
- A
- B
- D
- E
- F
- H
- I
- L
- M
- P
- Q
- R
- S
- T
- U
- V

Chapter 6: Port Mirroring

86 Section I: Basic Features

d. Using the stack ID pull-down menu in the upper left corner of the

switch image, select the ID number of the switch that has the port

that you want to make the new destination port. If the switch is

already displayed, you can skip this step.

e. Click the port until it turns solid white, as shown in Table 13 on

page 83.

f. Click Apply to close the Modify Mirror popup window.

8. To activate the port mirror again:

a. Click the Modify button.

b. Click the Enable Mirror checkbox to add the check and click the

Apply button.

9. To save your changes in the configuration file on the master switch,

click the Save Config button in the Configuration menu.