User Manual

ManualsBrandsAllied Telesis ManualsComputer HardwareAT-S63

100

Table Of Contents

Contents
Figures
Tables
Preface
- How This Guide is Organized
- Product Documentation
- Where to Go First
- Starting a Management Session
- Document Conventions
- Contacting Allied Telesis
Section I
Basic Operations
Chapter 1
Basic Switch Parameters
- Configuring the Stack’s Name, Location, and Contact
- Changing the Manager or Operator Password
- Setting the System Date and Time
- Resetting a Stack
- Pinging a Remote System
- Restoring the Factory Default Values
- Displaying the IP Address of the Local Interface
- Displaying System Information
Chapter 2
Port Parameters
- Configuring the Port Parameters
- Displaying the Port Parameters and Statistics
- Restoring the Default Settings on the Ports
Chapter 3
SNMPv1 and SNMPv2c
- Enabling or Disabling SNMP Management
- Creating New SNMPv1 and SNMPv2c Community Strings
- Modifying SNMPv1 and SNMPv2c Communities
- Deleting SNMPv1 and SNMPv2c Community Strings
- Displaying the SNMPv1 and SNMPv2c Community Strings
Chapter 4
MAC Address Table
- Displaying the MAC Address Table
- Adding Static Unicast or Multicast MAC Addresses
- Deleting Unicast or Multicast MAC Addresses
- Deleting All Dynamic MAC Addresses
- Changing the Aging Time
Chapter 5
Static Port Trunks
- Creating Static Port Trunks
- Modifying Static Port Trunks
- Deleting Static Port Trunks
- Displaying Static Port Trunks
Chapter 6
Port Mirroring
- Overview
- Creating the Port Mirror
- Modifying the Port Mirror
- Disabling the Port Mirror
- Deleting the Port Mirror
- Displaying the Port Mirror
Section II
Advanced Operations
Chapter 7
File System
- Listing the Files in Flash Memory or on a Compact Flash Card
- Selecting the Active Boot Configuration File
Chapter 8
File Downloads and Uploads
- General Guidelines
- Downloading a Master Configuration File
- Uploading a Configuration File or an Event Log File
Chapter 9
Event Logs and the Syslog Client
- Enabling or Disabling the Event Logs
- Displaying the Event Messages
- Clearing an Event Log
- Modifying an Event Log’s Full Action
- Saving an Event Log to a File
- Configuring Syslog Output Definitions
- Modifying Syslog Output Definitions
- Deleting Syslog Output Definitions
Chapter 10
IGMP Snooping
- Configuring IGMP Snooping
- Displaying the Host Nodes and the Multicast Routers
Section III
SNMPv3
Chapter 11
SNMPv3
- Configuring the SNMPv3 Protocol
- Enabling or Disabling SNMP Management
- Configuring the SNMPv3 User Table
- Configuring the SNMPv3 View Table
- Configuring the SNMPv3 Access Table
- Configuring the SNMPv3 SecurityToGroup Table
- Configuring the SNMPv3 Notify Table
- Configuring the SNMPv3 Target Address Table
- Configuring the SNMPv3 Target Parameters Table
- Configuring the SNMPv3 Community Table
- Displaying the SNMPv3 Tables
Section IV
Spanning Tree Protocols
Chapter 12
Spanning Tree and Rapid Spanning Tree Protocols
- Enabling or Disabling a Spanning Tree Protocol
- Configuring STP
- Configuring RSTP
Section V
Virtual LANs
Chapter 13
Port-based and Tagged VLANs
- Creating New Port-Based or Tagged VLANs
- Adding or Removing VLAN Ports
- Deleting VLANs
- Displaying VLANs
Section VI
Port Security
Chapter 14
802.1x Port-based Network Access Control
- Setting the Port Roles
- Enabling or Disabling 802.1x Port-based Network Access Control
- Configuring the Authenticator Port Parameters
- Configuring the Supplicant Port Parameters
- Displaying the Port Parameters and Port Status
- Configuring RADIUS Accounting
- Displaying the RADIUS Accounting Settings
Index
- Numerics
- A
- B
- D
- E
- F
- H
- I
- L
- M
- P
- Q
- R
- S
- T
- U
- V

Section II: Advanced Operations 91

Section II

Advanced Operations

This section has the following chapters:

 Chapter 7, “File System” on page 93

 Chapter 8, “File Downloads and Uploads” on page 99

 Chapter 9, “Event Logs and the Syslog Client” on page 105

 Chapter 10, “IGMP Snooping” on page 123