CONVERTEON™ Family Management Software AT-S70 User’s Guide CONVERTEON™ Family Media Converter Products Version 1.7.
Copyright © 2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis is a trademark of Allied Telesis, Inc. Microsoft and Internet Explorer are registered trademarks of Microsoft Corporation. Netscape Navigator is a registered trademark of Netscape Communications Corporation.
Contents Preface ............................................................................................................................................................................... 11 Where to Find Web-based Guides ...................................................................................................................................... 12 Contacting Allied Telesis ........................................................................................................................
Contents Displaying Detailed Line Card Information ................................................................................................................... 54 Displaying Line Card DIP Switch Settings .................................................................................................................... 56 Displaying Remote Module Status and Configuration Information ......................................................................................
AT-S70 Management Software User’s Guide Sending an OAM Variable Request................................................................................................................................... 133 Chapter 9: SNMPv3 ......................................................................................................................................................... 135 SNMPv3 Overview..................................................................................................................
Contents Downloading the Line Card Image and Bootloader Files to a Local Line Card ................................................................. 247 Downloading the Line Card Image File....................................................................................................................... 247 Downloading the Line Card Bootloader File ...............................................................................................................
Figures Figure 1. Connecting an RS-232 Cable to the Console Port on an AT-CV5M01 Management Card ............................... 23 Figure 2. Main Menu.......................................................................................................................................................... 25 Figure 3. System Configuration Menu ............................................................................................................................... 29 Figure 4. IP Parameters Menu.......
Figures Figure 51. Figure 52. Figure 53. Figure 54. Figure 55. Figure 56. Figure 57. Figure 58. Figure 59. Figure 60. Figure 61. Figure 62. Figure 63. Figure 64. Figure 65. Figure 66. Figure 67. Figure 68. Figure 69. Figure 70. Figure 71. Figure 72. Figure 73. Figure 74. Figure 75. Figure 76. Figure 77. Figure 78. Figure 79. Figure 80. Figure 81. Figure 82. Figure 83. Figure 84. Figure 85. Figure 86. Figure 87. Figure 88. Figure 89. Figure 90. Figure 91. Figure 92. Figure 93.
Tables Table 1. Menu Selection Options ...................................................................................................................................... 22 Table 2. Syslog Facility Applicable RFC 3164 Numerical Codes .................................................................................... 109 Table 3. OAM Active and Passive Mode Behaviors ........................................................................................................ 113 Table 4.
Tables 10
Preface This guide contains instructions on how to use the AT-S70 management software to manage and monitor the Converteon™ Series chassis, and how to upload or download the AT-S73 line card image onto Converteon™ Series line cards.
Preface Where to Find Web-based Guides The installation and user guides for all Allied Telesis products are available in portable document format (PDF) on our web site at www.alliedtelesis.com. You can view the documents online or download them onto a local workstation or server.
AT-S70 Management Software User’s Guide Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales and corporate information. Online Support You can request technical support online by accessing the Allied Telesis Knowledge Base from the following website: www.alliedtelesis.com/ support. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions.
Preface 14
Chapter 1 Overview The AT-S70 management software, with its menus interface, allows you to manage a Converteon™ Series chassis through an AT-CV5M01 Management Card.
Chapter 1: Overview Note To prevent unauthorized access, the management software program is password protected. If the password is changed and forgotten, you must call Allied Telesis Technical Support to have it reset back to the default password. For Technical Support contact information, refer to “Contacting Allied Telesis” on page 13.
AT-S70 Management Software User’s Guide Local Management Session You establish a local management session with a Converteon™ chassis by connecting a terminal or a PC with a terminal emulator program to the RS-232 Terminal Port on the management card installed in the front of the chassis, using the straight-through RS-232 management cable. This type of management session is referred to as “local” because you must be physically close to the chassis, such as in the wiring closet where the chassis is located.
Chapter 1: Overview Remote Management Session You can use any management workstation on your network that has the Telnet application protocol to manage a Converteon™ chassis. This type of management session is referred as a remote management session because you do not have to be in the wiring closet where the chassis is located. To establish a Telnet management session for any Converteon™ chassis, the chassis must have a management card and an IP address.
AT-S70 Management Software User’s Guide SNMP Management Session You can also remotely manage the Converteon™ chassis using an Simple Network Management Protocol (SNMP) management program such as HP Openview. This method, however, does not use the management interface. If you intend to manage the chassis from a management workstation using an SNMP management program, you need to load the following Management Information Base (MIB) file onto the management workstation.
Chapter 1: Overview Management Access Levels There are two levels of management access in the AT-S70 management software: manager and operator. When you log in as a manager, you can view and configure all operating parameters. When you log in as an operator, you can only view the operating parameters; you cannot change any values. You log in as a manager or an operator when you enter the appropriate username and password when you start an AT-S70 management session.
Chapter 2 Starting a Local or Remote Management Session This chapter describes the procedures for starting a local or remote management session on a Converteon™ chassis.
Chapter 2: Starting a Local or Remote Management Session Using the Menus Interface Table 1 lists the instructions on how to move through the menus and select menu options. Table 1. Menu Selection Options When directed to You must Highlight the option by pressing the Up ( ↑ ) or Down ( ↓ ) arrow key; then press Select an option or Type the first character of the desired option at the prompt and press .
AT-S70 Management Software User’s Guide Local Management Session The AT-CV5M01 Management Card has a port labelled “console.” You use this port to establish a local (out-of-band) management session through the AT-S70 management software. A chassis does not need an IP address for you to manage it from a local management session. You can start a local management session at any time on any Converteon™ chassis in your network.
Chapter 2: Starting a Local or Remote Management Session Note The Converteon™ chassis has an auto-detect feature on the serial port that automatically determines the speed of the local terminal. You activate this feature by pressing the Return or Enter key twice on your keyboard when you initially start the local interface or within five seconds after powering on or resetting the chassis.
AT-S70 Management Software User’s Guide The Main Menu is displayed, as shown in Figure 2. Allied Telesis AT-CV5M01 Management Module Software CV-5000 Chassis Main Menu Module Status and Configuration Remote Module Status and Configuration Administration Image Download System Configuration Quit Figure 2. Main Menu Quitting from a Local Management Session To end a local management session, return to the Main Menu and select Quit.
Chapter 2: Starting a Local or Remote Management Session Remote Management Session You can use any workstation on your network that has the Telnet application installed to manage a Converteon™ chassis. This type of management session is referred to as a remote management session because you do not have to be physically close to the chassis to start the session, such as with a local management session.
Chapter 3 Basic Parameters This chapter provides basic setup procedures for your Converteon™ Series chassis and contains the following sections: “When Does a Converteon™ Chassis Need an IP Address?” on page 28 “Saving the Configuration Settings” on page 29 “Configuring Basic Chassis Parameters” on page 30 “Configuring the Chassis Temperature Threshold” on page 37 “Pinging a Remote System” on page 38 “Restarting the Line Cards” on page 40 “Setting the RS-232 Terminal Baud Rate” o
Chapter 3: Basic Parameters When Does a Converteon™ Chassis Need an IP Address? When you assign a chassis an IP address, you must also assign it a subnet mask. The chassis uses the subnet mask to determine which portion of an IP address represents the network address and which the node address. You must also assign a gateway address to the chassis if the chassis and a remote management workstation are separated by a router.
AT-S70 Management Software User’s Guide Saving the Configuration Settings Whenever you change a setting, such as changing the speed of a port, you must specifically save the change to the configuration file. If you do not do so, these changes are lost when the chassis is reset or power cycled. To save the changes to the configuration file, perform the following procedure: 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 3.
Chapter 3: Basic Parameters Configuring Basic Chassis Parameters This section contains the following procedures: Naming the System “Naming the System,” next “Setting the System Date and Time” on page 30 “Configuring the System Location and Contact Information” on page 31 “Configuring the IP Address, Subnet Mask, and Default Gateway” on page 33 “Enabling or Disabling DHCP” on page 33 “Configuring the Management IP Addresses” on page 35 “Configuring SNMP Community Strings” on pag
AT-S70 Management Software User’s Guide chassis loses the values when it is reset or power cycled. Therefore, you must reset the values whenever you reset the chassis. To set the system’s date and time, perform the following procedure: 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 3 on page 29. 2. Adjust the following parameters as necessary: System Date(mm/dd/yy) Enter a date for the system in the “mm/dd/yy” format.
Chapter 3: Basic Parameters The IP Parameters Menu is displayed, as shown in Figure 4. IP Parameters Menu Converteon IP address: Subnet mask: Gateway address: 10.0.0.1 255.255.252.0 0.0.0.0 Manager Manager Manager Manager 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 address: address: address: address: Get community string: Set community string: Trap community string: public private public Location: Contact: California USA Allied Telesis > Disable DHCP Enable DHCP Return to System Configuration Menu...
AT-S70 Management Software User’s Guide Configuring the IP Address, Subnet Mask, and Default Gateway The procedure in this section explains how to manually assign an IP address, subnet mask, and gateway address to the chassis. To allow the chassis to obtain its IP configuration from a DHCP server on your network, go to “Enabling or Disabling DHCP” on page 33. To set the IP configuration for the chassis, perform the following procedure: 1. From the Main Menu, select System Configuration.
Chapter 3: Basic Parameters chassis. Note When you enable DHCP, any IP configuration settings that you manually assigned are overridden. Note BOOTP, another protocol that performs an identical function, is not supported on the Converteon™ chassis. To enable or disable the DHCP client software, perform the following procedure: 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 3 on page 29. 2.
AT-S70 Management Software User’s Guide Note When you enable the DHCP client software, the chassis immediately begins to query the network for a DHCP server. The chassis continues to query the network for its IP configuration until it receives a response. Any static IP address, subnet mask, and gateway address assigned to the chassis are deleted from the Administration menu and replaced with the values the chassis receives from DHCP server.
Chapter 3: Basic Parameters Configuring SNMP Community Strings To configure the SNMP community strings, perform the following procedure: Note SNMP access is disabled by default. To enable SNMP access, refer to “Configuring Management Access” on page 50. 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 3 on page 29. 2. From the System Configuration Menu, select IP Parameters.
AT-S70 Management Software User’s Guide Configuring the Chassis Temperature Threshold You can set a maximum temperature threshold for the chassis. Whenever the temperature threshold is exceeded, the chassis sends a trap to the management workstations. To set the chassis temperature threshold, perform the procedure: 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 3 on page 29. 2.
Chapter 3: Basic Parameters Pinging a Remote System You can instruct the chassis to ping a remote device on your network using the 10/100Base-TX port on the AT-CV5M01 Management Card. This procedure is useful in determining whether a valid link exists between the chassis and another device. The chassis sends an Internet Control Message Protocol (ICMP) echo request to the end node. If the end node is operating and receives the request, it sends a reply to the chassis.
AT-S70 Management Software User’s Guide 2. From the Administration Menu, select Ping a Remote System. The following message is displayed: Please enter Station IP Address to ping: 3. Enter the IP address of the end node to be pinged. 4. Press . The Omega interface activates the Activity Monitor window. This window reports the results of the ping command. The ping command continues until you press any key to stop it. 5. Press or select the “Return to ...
Chapter 3: Basic Parameters Restarting the Line Cards This procedure restarts the line cards. Note If DHCP is enabled, the IP address of the Converteon™ chassis MAY change after a reset or power cycle. For more information on how to enable DHCP, refer to “Enabling or Disabling DHCP” on page 33. To reset the chassis, perform the following procedure: 1. From the Main Menu, select Administration. The Administration Menu is displayed, as shown in Figure 6 on page 38. 2.
AT-S70 Management Software User’s Guide If you choose No, the Administration menu is redisplayed.
Chapter 3: Basic Parameters Setting the RS-232 Terminal Baud Rate Note The Converteon™ chassis has an auto-detect feature on the serial port that automatically determines the speed of the local terminal. You activate this feature by pressing the Return or Enter key twice on your keyboard when you initially start the local interface or within five seconds after powering on or resetting the chassis.
AT-S70 Management Software User’s Guide The Terminal Configuration Menu is displayed, as shown in Figure 8. Terminal Configuration Menu Converteon Data Rate (baud rate) ... Return to System Configuration Menu... Figure 8. Terminal Configuration Menu 3. From the Terminal Configuration Menu, select Data rate (baud rate). The Terminal Data Rate Menu is displayed, as shown in Figure 9.
Chapter 3: Basic Parameters 44
Chapter 4 Configuring Management Security Using the Omega Option This chapter describes the Omega options features in the AT-S70 software that can help prevent unauthorized individuals from changing the parameter settings of a Converteon™ chassis.
Chapter 4: Configuring Management Security Using the Omega Option Configuring the Manager and Operator Passwords The AT-S70 management software has two levels of management access: Manager and Operator. The Manager account allows you to configure all parameters of a Converteon™ chassis, while the Operator account only allows you to view the parameter settings. The default login name for Manager access is “manager” and the password is “friend”.
AT-S70 Management Software User’s Guide 2. From the System Configuration Menu, select Omega Options. The Omega Options Menu is shown in Figure 11. Omega Options Menu System Name: Manager Password: Operator Password: ***************** ***************** Timeout: 10 > Local Omega Enabled Disable Local Omega > Remote Omega Enabled No Remote Omega Return to System Configuration Menu... Figure 11. Omega Options Menu 3.
Chapter 4: Configuring Management Security Using the Omega Option 7. From the System Configuration Menu, select Save Configuration File.
AT-S70 Management Software User’s Guide Setting the Console Timeout The console timer causes the management software to automatically end a management session if it does not detect any activity from the local or remote management workstation during the specified period of time. This security feature can prevent unauthorized individuals from using your management workstation should you step away from your system while configuring a chassis. The default console timeout value is 10 minutes.
Chapter 4: Configuring Management Security Using the Omega Option Configuring Management Access To enable or disable a management access method, perform the following procedure: 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2. From the System Configuration Menu, select Omega Options. The Omega Options Menu is displayed, as shown in Figure 11 on page 47. 3.
Chapter 5 Working with Line Cards This chapter contains the following information for working with line cards and other modules using the management software: “Line Card Management Overview” on page 52 “Displaying Generic Line Card Information” on page 53 “Displaying Remote Module Status and Configuration Information” on page 58 “Configuring Generic Line Card Settings” on page 61 “Configuring the Line Card Operating Mode” on page 67 “Working with the AT-CM70S Line Card” on page 72
Chapter 5: Working with Line Cards Line Card Management Overview The Converteon chassis supports three series of line cards as identified by their model numbers: CV, CM, and the CV5M. The status information you can view and the changes you can make depend upon the line card model number. The line cards whose model number begin with “CV,” such as the AT-CV1KSS, are unmanaged cards and configuration options are limited to missing link, link testing, DIP switch settings, and limited port configuration.
AT-S70 Management Software User’s Guide Displaying Generic Line Card Information You can display general to specific information about the line cards using the following procedures: Displaying General Status Information “Displaying General Status Information,” next “Displaying Detailed Line Card Information” on page 54 “Displaying Line Card DIP Switch Settings” on page 56 To display the status of the modules and line cards in the Converteon™ chassis, perform the following procedure: 1.
Chapter 5: Working with Line Cards Status Indicates the current status of the line card. Possible status are: --: No line card or module installed. On: The line card is receiving power. Off: The line card is not receiving power. Resetting: The line card’s operational mode has been changed. Link (A) and Link (B) Displays whether there is an active connection between a port and the device connected to the port. Online indicates there is a link while Offline indicates there is no link.
AT-S70 Management Software User’s Guide To display line card status information, perform the following procedure: 1. From the Main Menu, select Module Status and Configuration. The Module Status and Configuration Menu is displayed, as shown in Figure 12 on page 53. 2. Select the line card whose information you want to display. 3. Press . An example of the Module Configuration Menu for the AT-CM202 line card is shown in Figure 13.
Chapter 5: Working with Line Cards Fiber port - 10M or 100M Copper port - Auto, 10M, or 100M Mode Displays the duplex mode of the ports. Possible values are: Auto - The port is auto-negotiating with the connected device to automatically configure to the highest common setting. Full - The port can send and receive data simultaneously. Half - The port can send or receive data, but not both at the same time.
AT-S70 Management Software User’s Guide The Module Configuration Menu (an example of the AT-CM202 line card is shown in Figure 13 on page 55) is displayed. 4. From the Module Configuration Menu, select Display DIP Switch Setting. The Display DIP Switch Setting menu is displayed, as shown in Figure 14. Display DIP Switch Setting Module 5 DIP Switch Operating Mode: SML Return to Module Status and Configuration ... Figure 14.
Chapter 5: Working with Line Cards Displaying Remote Module Status and Configuration Information The AT-S70 management software provides comprehensive status information about the operation of a remote module and its components. Note Allied Telesis Proprietary Remote Management – This feature is only supported on the AT-CM Series line cards such as the AT-CM202, and AT-CM212, and not the AT-CV Series line cards such as the AT-CV10x and AT-CV1KSS.
AT-S70 Management Software User’s Guide The Remote Module Status and Configuration Menu is displayed. The examples in Figure 15 and in Figure 16 show an AT-CV5000 chassis.
Chapter 5: Working with Line Cards Module Displays the model number of the module or line card and its slot number. Card Type Displays the model number of the remote line card. Version Displays the version number of the remote line card. Link Status (Port A) Displays the status of the connection between the ports on the local line card and the remote module. Possible status are: --: No link Online: Valid link No Support: Feature is not supported on the line card. More...
AT-S70 Management Software User’s Guide Configuring Generic Line Card Settings You can change the following settings to fit your network needs: Enabling and Disabling the Ports on a Line Card “Enabling and Disabling the Ports on a Line Card,” next “Changing the Line Card Port Duplex Mode” on page 62 “Configuring the Port Ingress/Egress Rate Limit” on page 63 When you enable the ports on a line card, you make it available to send and receive network traffic.
Chapter 5: Working with Line Cards 6. From the Port Management Menu, select Port Configurations. The Port Configuration Menu is displayed, as shown in Figure 18. Port Configuration Menu Converteon Module 4 - Port A > Port Enable Port Disable > Auto negotiate Full Half Ingress_Rate_Limit Egress_Rate_Limit Return to Module Management Menu... Figure 18. Port Configuration Menu 7. Select Port Enable to enable the port or Port Disable to disable the port. The default is enabled.
AT-S70 Management Software User’s Guide The Module Configuration Menu is displayed, as shown in Figure 13 on page 55. 4. Select the port to be configured. 5. Press . The Port Management Menu is displayed, as shown in Figure 18 on page 62. 6. From the Port Management Menu, select Port Configurations. The Port Configuration Menu is displayed, as shown in Figure 18 on page 62. 7. Select the one of the following duplex modes: Auto negotiate This is the default setting.
Chapter 5: Working with Line Cards Note The rate limit feature on an AT-CM2K0S line card differs from the feature described below. To configure the port rate limits on an AT-CM2K0S line card, refer to “Setting the Port Ingress and Egress Rate Limits” on page 88. To configure the ingress/egress rate limit on a line card, perform the following procedure: 1. From the Main Menu, select Module Status and Configuration. The Module Status and Configuration Menu is displayed, as shown in Figure 12 on page 53. 2.
AT-S70 Management Software User’s Guide The Port Ingress Rate Menu, shown in Figure 19, or the Port Egress Rate Menu, shown in Figure 20, is displayed. Port Ingress Rate Menu Converteon > Ingress_Rate_Limit_No Ingress_Rate_Limit_128K Ingress_Rate_Limit_256K Ingress_Rate_Limit_512K Ingress_Rate_Limit_1M Ingress_Rate_Limit_2M Ingress_Rate_Limit_4M Ingress_Rate_Limit_8M Return to Port Configuration Menu ... Figure 19.
Chapter 5: Working with Line Cards The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 9. From the System Configuration Menu, select Save Configuration File.
AT-S70 Management Software User’s Guide Configuring the Line Card Operating Mode By default, line cards are shipped without any operating mode selected. You can enable various operating modes by setting the DIP switches, as described in Appendix B, “DIP Switch Settings” on page 263 for detailed information. You can override the operating modes through the AT-S70 management software.
Chapter 5: Working with Line Cards connected to the fiber optic port that the connection on the twisted pair port has been lost. If the failure had started with the fiber optic cabling, the line card would drop the link to the twisted pair port. Some devices can be configured to take a specific action in the event of the loss of connection on a port, such as sending out a trap to a network management station to alert the network administrator of the problem.
AT-S70 Management Software User’s Guide Relationship Between the Line Card DIP Switches and the Line Card Operating Mode Configuring the Line Card Operating Mode When you enable any operating mode that is relevant to a particular line card, such as Smart MissingLink, that feature is enabled as the operating mode and you cannot select any other mode, even though it is enabled in the DIP switches. In order to enable the DIP switches, you must select the Line Card DIP Switch Mode.
Chapter 5: Working with Line Cards Note Only one operating mode can be active at a time. When you enable one mode, the others are disabled. Smart Missing Link Mode This mode performs exactly the same function as MissingLink™ with one additional feature. When a link is lost on a port, the LK LED of the port that still has a valid connection to its end node starts to blink.
AT-S70 Management Software User’s Guide The following prompt is displayed: Changing the Operation Mode will reset the line card. Change Operation Mode now? (Yes or No): 7. Type Y for Yes or N for No. and press . The Module Status and Configuration Menu is redisplayed and the module designation is shown as “Resetting” until the reset is complete. When the reset is complete, the new operating mode is displayed in the OpMode column. 8. From the Main Menu, select System Configuration.
Chapter 5: Working with Line Cards Working with the AT-CM70S Line Card The following sections describe operations related to the AT-CM70 line card: Displaying Status Information “Displaying Status Information,” next “Configuring the Local Console Settings” on page 74 “Configuring the T1/E1 Port Settings” on page 75 To view the status information an AT-CM70S line card, perform the following procedure: 1. From the Main Menu, select Module Status and Configuration.
AT-S70 Management Software User’s Guide Port Identifies the ports of the module. Link Displays the status of the link state on the ports. Online - Indicates that there is a valid link. Offline - Indicates that there is no link. Speed Displays the operating speed of the ports. Possible values are: Fiber port (Port A) - 10M or 100M Copper port (Port B) - Auto, 10M, or 100M Mode Displays the duplex mode of the ports.
Chapter 5: Working with Line Cards Configuring the Local Console Settings To change the TDM (time-division multiplexing) port parameters on the AT-CM70S line card from the local console, perform the following procedure: 1. Connect PC serial port to the Line card local console. Figure 23 is displayed upon boot up. You may need to turn the “Local Echo” setting on your AT-CM70S serial port terminal settings to ON. Figure 23.
AT-S70 Management Software User’s Guide T1 DSX-1(133 to 266ft) T1 DSX-1(266 to 399ft) T1 DSX-1(399 to 533ft) T1 DSX-1(533 to 655ft) T1 -7.5dB CSU T1 -15dB CSU T1 -22.
Chapter 5: Working with Line Cards The Module Status and Configuration Menu is displayed, as shown in Figure 12 on page 53. 2. Select the AT-CM70S line card whose information you want to change. 3. Press . The Module Configuration Menu is displayed, as shown in Figure 13 on page 55. 4. From the Module Configuration Menu, select TDM LIU (T1/E1) Configuration. The TDM Management Menu is displayed, as shown in Figure 24.
AT-S70 Management Software User’s Guide The LIU Mode and Channel Select Menu is displayed, as shown in Figure 25. LIU Mode and Channel Select Menu Module 15, Port C > Manufacture T1 Mode Manufacture E1 Mode Customized Mode Channel 1, Sub-Menu 1 Channel 1, Sub-Menu 2 Channel 2, Sub-Menu 1 Channel 2, Sub-Menu 2 Channel 3, Sub-Menu 1 Channel 3, Sub-Menu 2 Channel 4, Sub-Menu 1 Channel 4, Sub-Menu 2 Return to Port Configuration Menu ... Figure 25. LIU Mode and Channel Select Menu 6.
Chapter 5: Working with Line Cards Channel (1 to 4) , Sub-Menu 1 When one of these parameters is selected, the TDM Channel Configuration Menu 1 is displayed, as shown in Figure 26. TDM Channel Configuration Menu 1 Module 15, Port C > Long Haul Limited Long Haul > T1 T1 T1 T1 T1 T1 T1 T1 DSX-1(0 to 133ft)/0dB CSU DSX-1(133 to 266ft) DSX-1(266 to 399ft) DSX-1(399 to 533ft) DSX-1(533 to 655ft) -7.5dB CSU -15dB CSU -22.5dB CSU Return to LIU Mode and Channel Select Menu ... Figure 26.
AT-S70 Management Software User’s Guide Channel (1 to 4) , Sub-Menu 2 When one of these parameters is selected, the TDM Channel Configuration Menu 2 is displayed, as shown in Figure 27. TDM Channel Configuration Menu 2 Module 15, Port C Transmit All Ones > Transmit Data Normally > Transmit PRBS Disable Transmit PRBS Enable > Remote Loopback Disable Remote Loopback Enable > Local Loopback Disable Local Loopback Enable Return to LIU Mode and Channel Select Menu ... Figure 27.
Chapter 5: Working with Line Cards If you choose to change the operation mode of the line card TDM port. The following prompt is displayed: Change Operation Mode now? (Yes or No): 8. Type Y to accept the changes to the TDM port configuration, or type N to cancel the changes. 9. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 10. From the System Configuration Menu, select Save Configuration File.
AT-S70 Management Software User’s Guide Figure 28. UART Configuration Menu 6. From the UART Configuration Menu, select one of the following configurations: UART Local Console Mode Sets the UART configuration to communicate with other computers via the local console mode. This is the default setting. UART Back Plane Mode Sets the UART configuration to communicate with the computers via the backplane mode.
Chapter 5: Working with Line Cards Working with the AT-CV5M01 Management Card The following sections describe operations related to the AT-CV5M01Management Card: Displaying Port Status Information “Displaying Port Status Information,” next “Working with a Redundant AT-CV5M01 Management Card” on page 83 “Resetting the AT-CV5M01 Management Card” on page 84 The following procedure allows you to view the parameter settings of the 10/100Base-TX port on the AT-CV5M01 Management Card.
AT-S70 Management Software User’s Guide Port Identifies the port on the module. Link Displays the status of the link state on the port. Online - Indicates there is a valid link. Offline - Indicates there is no link. Speed Displays the operating speed of the port. Possible values are Auto, 10M or 100M. Mode Displays the duplex mode of the ports. Possible values are: Auto - The port is auto-negotiating with the connected device to automatically configure to the highest common setting.
Chapter 5: Working with Line Cards 3. Press . The CPM switch over menu is displayed, as shown in Figure 30. Converteon Do CPM switch over ? (Yes or No): Yes > No Return to Administration Menu ... Figure 30. CPM Switchover Menu 4. Choose Yes to start the switchover process or choose No to cancel. Resetting the AT-CV5M01 Management Card To reset the AT-CV5M01Management Card and restart the AT-S70 management software, perform the following procedure: 1.
AT-S70 Management Software User’s Guide Working with the AT-CM2K0S Line Card The AT-CM2K0SCM2K0S line card has several features not found on other line cards.
Chapter 5: Working with Line Cards 4. From the Configuration Menu, select Configure Max Frame Size. 5. Press . The Max Frame Size Config Menu is displayed, as shown in Figure 32. Max Frame Size Config Menu Module 14 > Max Frame Size: 1522/1518 Max Frame Size: 1632 Return to Module Configuration Menu ... Figure 32. Max Frame Size Config Menu 6. From the Max Frame Size Config Menu, select one of the following frame sizes: 1522/1518 Allows frames up to 1522 bytes. This is the default.
AT-S70 Management Software User’s Guide The Port Management Menu is displayed, as shown in Figure 33. Port Management Menu Module 14 - Port A Port Configuration Return to Module Configuration Menu... Figure 33. Port Management Menu for the AT-CM2K0S 5. From the Port Management Menu, select Port Configuration. The Port Configuration Menu for the SFP port is shown in Figure 34.
Chapter 5: Working with Line Cards The Show Port Statistics Menu is displayed, as shown in Figure 35. Show Port Statistics Module 14 - Port B Received Packets Transmitted Packets CRC Errors Collisions Return to Port Statistics ... Figure 35. Show Port Statistics Menu Setting the Port Ingress and Egress Rate Limits Rate limiting helps prevent traffic congestion on a network by allowing you to set a rate limit from 70 to 250,000 Kb/s for traffic coming into or exiting a port.
AT-S70 Management Software User’s Guide Note The process for setting the ingress or egress rate limit is the same, except for the selection of ingress or egress. Therefore, the figures in the rest of this procedure illustrate setting the ingress rate limit as an example of how to do both. The Port Ingress Rate Menu is displayed, as shown in Figure 36. Port Ingress Rate Menu Module 14, Port B Show Ingress Rate Limit Set Ingress Rate Limit Return to Port Configuration Menu ... Figure 36.
Chapter 5: Working with Line Cards Displaying the Port Ingress and Egress Rate Limits To display the ingress and/or egress rates for a port on an AT-CM2K0S line card, perform the following procedure: 1. From the Main Menu, select Module Status and Configuration. The Module Status and Configuration Menu is displayed, as shown in Figure 12 on page 53. 2. Select the AT-CM2K0S line card whose information you want to change. 3. Press .
Chapter 6 Monitoring System Performance This chapter describes the features in the AT-S70 for monitoring the performance of the Converteon™ chassis.
Chapter 6: Monitoring System Performance Using the System Activity Monitor The AT-S70 management software keeps a list of the chassis SNMP events, such as removal of a line card, loss of a data link, and failure of a fan module. This list is called the activity log and you use the activity monitor to display the log. The activity log contains only those events that have occurred since you started the management session. Ending the session purges the log.
AT-S70 Management Software User’s Guide Starting and Stopping the Activity Monitor To start or stop the activity log, perform the following procedure: 1. From the Main Menu, select Administration. The Administration Menu is displayed, as shown in Figure 6 on page 38. 2. From the Administration Menu, select Start Activity Monitor to start the activity monitor or Stop Activity Monitor to stop the activity monitor. The default is Stop Activity Monitor.
Chapter 6: Monitoring System Performance Using the System Diagnostics The AT-S70 management software can run a series of diagnostic selftests on the chassis and line cards. The following section describes how to run chassis diagnostics. This information can help you diagnose performance problems with the chassis.
AT-S70 Management Software User’s Guide The Diagnostics Menu is displayed, as shown in Figure 38. Diagnostics Menu Converteon Chassis Diagnostics Line Card Image Version Line Card Information SFP Information Return to Administration Menu... Figure 38. Diagnostics Menu 3. From the Diagnostics Menu, select Chassis Diagnostics. The AT-S70 management software runs the diagnostics on the chassis and displays the results in the Chassis Diagnostics menu. The example in Figure 39 shows an AT-CV5000 chassis.
Chapter 6: Monitoring System Performance The information displayed on the Chassis Diagnostics Menu is for viewing purposes only. The Chassis Diagnostics menu contains the following items of system information: Serial Number Displays the serial number and hardware revision level of the system. MAC Address Displays the MAC address of the chassis. Converteon Chassis Displays the Converteon™ chassis model and revision, such as “AT-CV5000 Revision 1.7.
AT-S70 Management Software User’s Guide Displaying the Line Card Software Versions To view the application and bootloader versions of the software on the line cards, perform the following procedure: 1. From the Main Menu, select Administration. The Administration Menu is displayed, as shown in Figure 6 on page 38. 2. From the Administration Menu, select Diagnostics. The Diagnostic Menu is displayed, as shown in Figure 38 on page 95. 3. From the Diagnostics Menu, select Line Card Image Version.
Chapter 6: Monitoring System Performance The Line Card Module Software Image Version menu contains the following information: Module Displays the name of the module or line card and its slot number. App Ver. Displays the software version on the line cards. BootLdr Ver. Displays the bootloader version on the line cards. 4. Press or hit any key to continue.
AT-S70 Management Software User’s Guide Displaying Line Card Information To view the MAC addresses and serial numbers of the line cards, perform the following procedure: 1. From the Main Menu, select Administration. The Administration Menu is displayed, as shown in Figure 6 on page 38. 2. From the Administration Menu, select Diagnostics. The Diagnostic Menu is displayed, as shown in Figure 38 on page 95. 3. From the Diagnostics Menu, select Line Card Information.
Chapter 6: Monitoring System Performance Module Displays the model name of the module or line card and its slot number. MAC Address Displays the MAC address of a line card. Serial Number Displays the serial number of a line card. 4. Press or hit any key to continue.
AT-S70 Management Software User’s Guide Displaying SFP Module Information To view the operating specifications of an SFP module information, perform the following procedure: 1. From the Main Menu, select Administration. The Administration Menu is displayed, as shown in Figure 6 on page 38. 2. From the Administration Menu, select Diagnostics. The Diagnostic Menu is displayed, as shown in Figure 38 on page 95. 3. From the Diagnostics Menu, select SFP Information.
Chapter 6: Monitoring System Performance The SFP Information window is displayed, as shown in Figure 43 and Figure 43, and lists the specifications of the selected SFP module.
Chapter 7 Event Log and Syslog Servers This chapter describes how to view and clear the contents of the event log. The event log allows you to view chassis information. This chapter also discusses how to configure the chassis to send its events to a syslog server.
Chapter 7: Event Log and Syslog Servers Event Log Overview A managed Converteon™ media chassis is a complex piece of computer that includes both hardware and software. Multiple software features operate simultaneously, interoperating with each other and processing large amounts of network traffic. It is often difficult to determine exactly what is happening when a chassis appears not to be operating normally, or what happened when the problem occurred.
AT-S70 Management Software User’s Guide Working with the Event Log This section contains the following procedures: Displaying the Event Log “Displaying the Event Log,” next “Clearing the Event Log” on page 107 To display the events in the event log, perform the following procedure: 1. From the Main Menu, select Administration. The Administration Menu is displayed, as shown in Figure 6 on page 38. 2. From the Administration Menu, select Event Log.
Chapter 7: Event Log and Syslog Servers An example of an event log is shown in Figure 45. Converteon Event Log Total Events: 8.
AT-S70 Management Software User’s Guide Clearing the Event Log To clear all the events in the event log and start fresh, perform the following procedure: 1. From the Main Menu, select Administration. The Administration Menu is displayed, as shown in Figure 6 on page 38. 1. From the Administration Menu, select Event Log. The Event Log Menu window is displayed, as shown in Figure 44 on page 105. 2. From the Event Log Menu, select Clear Event Log.
Chapter 7: Event Log and Syslog Servers Configuring the Syslog Server This section about the syslog server contains the following procedures: Configuring the Syslog Server’s IP Address “Configuring the Syslog Server’s IP Address,” next “Setting the Syslog Facility Code” on page 108 The chassis can only use the 10/100Base-TX port on the AT-CV5M01 Management Card to send out the packets to the sysLog server.
AT-S70 Management Software User’s Guide module or system that produced them. This grouping helps you determine which events belong to which device when a syslog server is collecting events from several network devices. You can specify only one facility code. To specify a facility code to include in the events sent to a syslog server, perform the following procedure: 1. From the Main Menu, select Administration. The Administration Menu is displayed, as shown in Figure 6 on page 38. 2.
Chapter 7: Event Log and Syslog Servers Table 2. Syslog Facility Applicable RFC 3164 Numerical Codes Numerical Code Facility 16 Local use 0 (LOCAL0) 17 Local use 1 (LOCAL1) 18 Local use 2 (LOCAL2) 19 Local use 3 (LOCAL3) 20 Local use 4 (LOCAL4) 21 Local use 5 (LOCAL5) 22 Local use 6 (LOCAL6) 23 Local use 7 (LOCAL7) 1 Various operating systems have been found to utilize Facilities 4, 10, 13 and 14 for security/authorization, audit, and alert messages which seem to be similar. 2.
Chapter 8 Operations, Administration, and Maintenance (OAM) This chapter describes the Operations, Administration, and Maintenance (OAM) feature, which provides mechanism useful for monitoring link operation such as remote fault indication and remote loopback control. In general, OAM provides network operators the ability to monitor the condition of the network and determine the location of the failing links or fault conditions.
Chapter 8: Operations, Administration, and Maintenance (OAM) Overview The Operation, Administration and Maintenance (OAM) is a group of functions that provides tools and utilities used to manage a network. The OAM feature is 802.3ah-compliant and is used to provide network indication, system configuration, performance monitoring, security management, diagnostic functions and configuration.
AT-S70 Management Software User’s Guide (OAMPDUs) for five seconds, the OAM discovery process will restart. One important aspect of the IEEE 802.3ah OAM spec is that an OAM entity may be in either Active or Passive mode. Active Mode – Active-mode stations forward OAM communications and can send queries and commands to a remote station. Passive Mode – Passive-mode stations wait for the peer station to forward OAM communications and then respond to commands and queries.
Chapter 8: Operations, Administration, and Maintenance (OAM) length-value (TLV) encoding of attributes within the type. The OAMPDU types are: Information OAMPDUs – Information OAMPDUs are used for discovery; they are variable-length OAMPDUs. There are three TLVs for Information PDUs: Local Information, Remote Information, and Organizational Specific. Local and Remote Information is used in the discovery process. The Organizational Specific Information TLV is used for vendor extensions.
AT-S70 Management Software User’s Guide Configuring OAM Operations on a Port To configure the OAM operations, perform the following procedure: 1. From the Main Menu, select Module Status and Configuration. The Module Status and Configuration Menu is displayed, as shown in Figure 46. Note The information displayed in this menu varies depending on the chassis used. For illustration purposes, an AT-CV5000 chassis is shown in Figure 46.
Chapter 8: Operations, Administration, and Maintenance (OAM) The Module Configuration Menu is displayed, similar to the one in Figure 47. Module Configuration Menu Converteon Module 4 Module: AT-CM202 Port A(100BaseFX) B(100BaseTX) Link Online ONline Speed 100M 10M Mode Full Half RX/ACT Off Off Configure Operating Mode Return to Module Status and Configuration Menu... Figure 47. Module Configuration Menu (Line Card) 4. Select the port whose OAM operations you want to configure. 5. Press .
AT-S70 Management Software User’s Guide The OAM Configuration Menu is displayed, as shown in Figure 49. OAM Configuration Module 4, Port A OAM Configuration Show Local OAM Information Show Remote OAM Information Show OAM Statistics OAM Loopback Test Send OAM Variable Request Return to Port Management Menu ... Figure 49. OAM Configuration Menu 7. From the OAM Configuration Menu, select OAM Configuration. The OAM Configuration submenu is displayed, as shown in Figure 50.
Chapter 8: Operations, Administration, and Maintenance (OAM) Enabled – The OAM administration status is enabled. (default) Disabled – The OAM administration status is disabled. Mode Indicates that the OAM sublayer entity is either in Active or Passive mode. Possible values are: Passive – The OAM sublayer entity is configured in Passive mode. (default) Active – The OAM sublayer entity is configured in Active mode.
AT-S70 Management Software User’s Guide Variable Retrieval Support Indicates whether or not the chassis supports sending Variable Response OAMPDUs. Yes – Supports sending Variable Response OAMPDUs. (default) No – Does not support sending Variable Response OAMPDUs. 8. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 9. From the System Configuration Menu, select Save Configuration File.
Chapter 8: Operations, Administration, and Maintenance (OAM) Displaying OAM Information and Statistics This section contains the following procedures for displaying the OAM information and statistics for a local or remote module: Displaying OAM Information for a Local Module Port “Displaying OAM Information for a Local Module Port,” next “Displaying OAM Information for a Remote Module Port” on page 125 To display the status on the local OAM, perform the following procedure: 1.
AT-S70 Management Software User’s Guide The Show Local OAM Information Menu is displayed, as shown in Figure 51.
Chapter 8: Operations, Administration, and Maintenance (OAM) Converteon™ to be used in a network where the Converteon™ chassis is not part of the IEEE802.3ah end points. In this mode, the OAM function of the line card is disabled. To configure as OAM bypass mode, the module will pass all OAMPDUs whose vendor OUI is not Allied Telesis. OAM Visible Mode – In this mode, the line card does respond to OAMPDU packets. In an unmanaged chassis, the line card will be in passive mode.
AT-S70 Management Software User’s Guide in the latest OAMPDU. This value is changed based on loopback actions by either the local or remote station. Possible values are: Forward – Parser passes received non-OAMPDUs to superior sublayer. (default) Loopback – Parser passes received non-OAMPDUs to Multiplexer during remote loopback test. Discard – Parser discards received non-OAMPDUs. Local Discovering Indicates the local station can accept or reject the configuration of the peer OAM entity.
Chapter 8: Operations, Administration, and Maintenance (OAM) No – No severe error condition has occurred. (default) Dying Gasp Indicates an unrecoverable failure condition has occurred when an equipment is about to be reset, reboot, or otherwise having a power failure. Yes – An unrecoverable local failure condition has occurred. No – No unrecoverable local failure condition has occurred. (default) Link Fault Indicates the PHY has determined a fault has occurred in the receive direction of the local port.
AT-S70 Management Software User’s Guide frame received is transmitted back on that same port except for the OAMPDUs and pause frames. The loopback command is acknowledged by responding with an information OAMPDU with the loopback state indicated in the state field. OAMPDUs continue to be exchanged during loopback mode, only data frames are looped back. Terminating Loopback – When the local station wishes to end the OAM loopback test, the local MAC Client stops sending frames.
Chapter 8: Operations, Administration, and Maintenance (OAM) 5. Press . The Port Management Menu is displayed, as shown in Figure 48 on page 116. 6. From the Port Management Menu, select OAM Configurations. The OAM Configuration Menu is displayed, as shown in Figure 49 on page 117. 7. From the OAM Configuration Menu, select the Show Remote OAM Information Menu. The Show Remote OAM Information Menu is displayed, shown in Figure 52.
AT-S70 Management Software User’s Guide 3. Press . The Module Configuration Menu is displayed, as shown in Figure 47 on page 116. 4. Select the port whose OAM statistics you want to display. 5. Press . The Port Management Menu is displayed, as shown in Figure 48 on page 116. 6. From the Port Management Menu, select OAM Configurations. The OAM Configuration Menu is displayed, as shown in Figure 49 on page 117. 7. From the OAM Configuration Menu, select the Show OAM Statistics Menu.
Chapter 8: Operations, Administration, and Maintenance (OAM) The Show OAM Statistics Menu is displayed, as shown in Figure 53.
AT-S70 Management Software User’s Guide OAM Loopback Test This section contains the following procedures for managing the OAM loopback test: Enabling or Disabling a Remote Loopback Test “Enabling or Disabling a Remote Loopback Test,” next “Starting or Stopping a Loopback Test” on page 130 “Displaying or Clearing the Loopback Test Statistics” on page 131 To enable or disable the OAM remote loopback test, perform the following procedure: 1.
Chapter 8: Operations, Administration, and Maintenance (OAM) The OAM Loopback Test Menu is displayed, as shown in Figure 54. OAM Loopback Test Module = 5, Port = 1 Enable Remote Loopback > Disable Remote Loopback Start Loopback Test > Stop Loopback Test Show Loopback Test Statistics Clear Loopback Test Statistics Return to OAM Configurations ... Figure 54. OAM Loopback Test Menu 8.
AT-S70 Management Software User’s Guide 5. Press . The Port Management Menu is displayed, as shown in Figure 48 on page 116. 6. From the Port Management Menu, select OAM Configurations. The OAM Configuration Menu is displayed, as shown in Figure 49 on page 117. 7. From the OAM Configuration Menu, select the OAM Loopback Test Menu. The OAM Loopback Test Menu is displayed, as shown in Figure 54 on page 130. 8.
Chapter 8: Operations, Administration, and Maintenance (OAM) The OAM Configuration Menu is displayed, as shown in Figure 49 on page 117. 7. From the OAM Configuration Menu, select the OAM Loopback Test Menu. The OAM Loopback Test Menu is displayed, as shown in Figure 54 on page 130. 8. From the OAM Loopback Test Menu, select Show Loopback Test Statistics to display the current loopback test statistics, or select Clear Loopback Test Statistics to clear all current loopback test statistics.
AT-S70 Management Software User’s Guide Sending an OAM Variable Request To send an OAM variable request, perform the following procedure: 1. From the Main Menu, select Module Status and Configuration. The Module Status and Configuration Menu is displayed, as shown in Figure 46 on page 115. 2. Select the line card whose OAM variable request you want to send. 3. Press . The Module Configuration Menu is displayed, as shown in Figure 47 on page 116. 4.
Chapter 8: Operations, Administration, and Maintenance (OAM) 9. Enter a number of the specific package or object being returned. The default is 1. 10. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 11. From the System Configuration Menu, select Save Configuration File.
Chapter 9 SNMPv3 This chapter provides a description of the AT-S70 implementation of the SNMPv3 protocol. In addition, the chapter contains procedures that allow you to create and modify SNMPv3 entities.
Chapter 9: SNMPv3 SNMPv3 Overview The SNMPv3 protocol builds on the existing SNMPv1 and SNMPv2c protocol implementation. In SNMPv3, User-based Security Model (USM) authentication is implemented along with encryption, allowing you to configure a secure SNMP environment. In addition, SNMP terminology changes in the SNMPv3 protocol. In the SNMPv1 and SNMPv2c protocols, the terms agent and manager are used. An agent is an SNMP user while a manager is an SNMP host.
AT-S70 Management Software User’s Guide protocols use keys to perform authentication. The keys for both protocols are generated locally using the Engine ID, a unique identifier that is assigned to the switch automatically, and the user password. You modify a key only by modifying the user password. In addition, you have the option of assigning no user authentication. In this case, no authentication is performed for this user. You may want to make this configuration for someone with super-user capabilities.
Chapter 9: SNMPv3 SNMPv3 MIB Views The SNMPv3 protocol allows you to configure MIB views for users and groups. The MIB tree is defined by RFC 1155 (Structure of Management Information), as illustrated in Figure 58.
AT-S70 Management Software User’s Guide MIB subtree view and a subtree mask is analogous to the relationship between an IP address and a subnet mask. The switch uses the subnet mask to determine which portion of an IP address represents the network address and which portion represents the node address. In a similar way, the subtree mask further refines the subtree view and enables you to restrict a MIB view to a specific row of the OID MIB table.
Chapter 9: SNMPv3 To configure the SNMP security information, you associate a user and its related information—View, Security Level, Security Model, Authentication Level, Privacy Protocol and Group—with the type of message and the host IP address. SNMPv3 Tables The SNMPv3 configuration is neatly divided into configuring SNMPv3 user information and configuring the message notification. You must configure all seven tables to successfully configure the SNMPv3 protocol.
AT-S70 Management Software User’s Guide After you configure an SNMPv3 user, you need to configure SNMPv3 message notification. This configuration is accomplished with the following tables: Configure SNMPv3 Notify Table Configure SNMPv3 Target Address Table Configure SNMPv3 Target Parameters Table You start the message notification configuration by defining the type of message you want to send with the SNMPv3 Notify Table.
Chapter 9: SNMPv3 For a more detailed description of the SNMPv3 Tables, see the following subsections: “SNMPv3 User Table” on page 142 “SNMPv3 View Table” on page 142 “SNMPv3 Access Table” on page 142 “SNMPv3 Group Table” on page 143 “SNMPv3 Notify Table” on page 143 “SNMPv3 Target Address Table” on page 143 “SNMPv3 Target Parameters Table” on page 143 SNMPv3 User Table The Configure SNMPv3 User Table menu allows you to create an SNMPv3 user and provides the options of configuri
AT-S70 Management Software User’s Guide group members to view the specified portion of the OID MIB table. The Write View allows group members to write to, or modify, the MIBs in the specified MIB view. The Notify View allows group members to send trap messages defined by the MIB view. Lastly, you can configure a storage type for this table entry which allows you to save this view to flash memory.
Chapter 9: SNMPv3 SNMPv3 Configuration Example 144 You may want to have two classes of SNMPv3 users—Managers and Operators. In this scenario, you would configure one group, called Managers, with full access privileges. Then you would configure a second group, called Operators, with monitoring privileges only. For a detailed example of this configuration, see Appendix B, “SNMPv3 Configuration Examples” on page 891.
AT-S70 Management Software User’s Guide Configuring SNMPv3 Entities This section describes how to configure SNMPv3 entities using the SNMPv3 Tables. To successfully configure this protocol, you must perform the procedures in the order given. For overview information about SNMPv3, see the “SNMPv3 Overview” on page 136.
Chapter 9: SNMPv3 Configuring the SNMPv3 User Table This section contains a description of the SNMPv3 User Table and how to create, delete, and modify table entries. Configure the SNMPv3 User Table first. Creating this table, allows you to create an entry in an SNMPv3 User Table for a User Name.
AT-S70 Management Software User’s Guide SNMPv3 Configurations Converteon Configure SNMPv3 User Table Configure SNMPv3 View Table Configure SNMPv3 Access Table Configure SNMPv3 Group Table Configure SNMPv3 Notify Table Configure SNMPv3 Target Address Table Configure SNMPv3 Target Parameters Table Save SNMPV3 Configuration Load SNMPV3 Configuration Return to System Configuration Menu ... Figure 61. SNMPv3 Configurations Menu 3. From the SNMPv3 Configurations menu, select Configure SNMPv3 User Table.
Chapter 9: SNMPv3 5. Enter a descriptive name of the user. You can enter a name that consists of up to 32 alphanumeric characters. The following prompt is displayed: Enter Authentication Protocol [M-MD5, S-SHA, N-None]: 6. Enter one of the following: M-MD5 This value represents the MD5 authentication protocol. With this selection, users (SNMP entities) are authenticated with the MD5 authentication protocol after a message is received. This algorithm generates the message digest.
AT-S70 Management Software User’s Guide Note You can only configure the Privacy Protocol if you have configured the Authentication Protocol with the MD5 or SHA values. 8. Select one of the following options: D-DES Select this value to make the DES privacy (or encryption) protocol the privacy protocol for this User Table entry. With this selection, messages transmitted between the host and the switch are encrypted with the DES protocol.
Chapter 9: SNMPv3 12. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 13. From the System Configuration Menu, select Save Configuration File. Deleting an SNMPv3 User Table Entry You may want to delete an entry from the SNMPv3 User Table. When you delete an entry in the SNMPv3 User Table, there is no way to undelete, or recover the entry. To delete an entry in the SNMPv3 User Table, perform the following procedure. 1.
AT-S70 Management Software User’s Guide 8. From the System Configuration Menu, select Save Configuration File.
Chapter 9: SNMPv3 Modifying an SNMPv3 User Table Entry This section describes how to modify parameters in an SNMPv3 Notify Table entry.
AT-S70 Management Software User’s Guide The following prompt is displayed: Enter User (Security) Name: 6. Enter the User Name of the User Table you want to modify. The following prompt is displayed: Enter Authentication Protocol [M-MD5, S-SHA, N-None]: 7. Enter one of the following: M-MD5 This value represents the MD5 authentication protocol. With this selection, users (SNMP entities) are authenticated with the MD5 authentication protocol after a message is received.
Chapter 9: SNMPv3 11. From the System Configuration Menu, select Save Configuration File.
AT-S70 Management Software User’s Guide Modifying the Privacy Protocol and Password To modify the Privacy Protocol and Password in an SNMPv3 User Table entry, perform the following procedure. Note You can only configure the Privacy Protocol if you have configured the Authentication Protocol with the MD5 or SHA values. 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2.
Chapter 9: SNMPv3 messages transmitted between the host and the switch are encrypted with the DES protocol. N -None Select this value if you do not want a privacy protocol for this User Table entry. With this selection, messages transmitted between the host and the switch are not encrypted. If you select None, proceed to step 10. If you select DES, the following prompt is displayed: Enter Privacy Password: 8.
AT-S70 Management Software User’s Guide 4. From the Configure SNMPv3 User Table menu, select Modify SNMPv3 Table Entry. The Modify SNMPv3 User Table is displayed, as shown in Figure 63 on page 152. 5. To change the storage type, select Set Storage Type. The following prompt is displayed: Enter User (Security) Name: 6. Enter the User Name. The following prompt is displayed: Enter Storage Type [V-Volatile, N-NonVolatile]: 7.
Chapter 9: SNMPv3 The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. 3. From the SNMPv3 Configurations menu, select Configure SNMPv3 User Table. The Configure SNMPv3 User Table menu is displayed, as shown in Figure 62 on page 147. 4. From the Configure SNMPv3 User Table menu, select Display SNMPv3 Table Entry. The Snmpv3 User Info menu is displayed, as shown in Figure 64. Converteon SNMPv3 User Info: Engine Id ............... User Name ................ Authentication Protocol .
AT-S70 Management Software User’s Guide Configuring the SNMPv3 View Table This section contains a description of the SNMPv3 View Table and how to create, delete, and modify table entries. Creating this table, allows you to specify a view using the following parameters: Subtree OID Subtree Mask MIB OID Table View To configure the SNMPv3 View Table, you need to be very familiar with the OID table.
Chapter 9: SNMPv3 The Configure SNMPv3 View Table menu is displayed, as shown in Figure 65. Configure SNMPv3 View Table Converteon Create SNMPv3 Table Entry Delete SNMPv3 Table Entry Modify SNMPv3 Table Entry Display SNMPv3 Table Entry Return to SNMPv3 Configurations ... Figure 65. Configure SNMPv3 View Table Menu 4. From the Configure SNMPv3 View Table menu, select Create SNMPv3 Table Entry. The following prompt is displayed: Enter View Name: 5. Enter a descriptive name of this View.
AT-S70 Management Software User’s Guide 7. Enter a subtree mask in hexadecimal format. This is an optional parameter that is used to further refine the value in the View Subtree parameter. This parameter is in binary format. The relationship between a subtree mask and a subtree is similar to the relationship between an IP address and a subnet mask. The subnet mask further refines the IP address.
Chapter 9: SNMPv3 10. Type Y to create a new table entry, or type N to cancel the entry. 11. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 12. From the System Configuration Menu, select Save Configuration File. Deleting an SNMPv3 View Table Entry You may want to delete an entry from the SNMPv3 View Table. Note Once an SNMPv3 View Table entry is deleted, there is no way to undelete, or recover the entry.
AT-S70 Management Software User’s Guide The following prompt is displayed: Do you want to Delete this table entry? (Yes or No): 7. Enter Y to delete the selected table entry or N to save the entry. 8. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 9. From the System Configuration Menu, select Save Configuration File.
Chapter 9: SNMPv3 The Modify SNMPv3 Table Entry menu is displayed, as shown in Figure 66. Converteon Configure SNMPv3 View Table Modify SNMPv3 Table Entry Set Subtree Mask Set View Type Set Storage Type Return to Configure SNMPv3 View Table ... Figure 66. Modify SNMPv3 View Table Menu 5. To modify the Subtree Mask for this view, select Set Subtree Mask. The following prompt is displayed: Enter View Name: 6. Enter an existing View Name.
AT-S70 Management Software User’s Guide parameter is dependent on the subtree you select. For example, if you configure the View Subtree parameter as MIB, ifEntry.0.3 has the following value: 1.3.6.1.2.1.2.2.1.0.3 To restrict the user’s view to the third row (all columns) of the ifEntry MIB, enter the following value for the Subtree Mask parameter: ff:bf 9. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 10.
Chapter 9: SNMPv3 Enter View Subtree (OID format/Text Name): 7. Enter the View Subtree value for this View Name. You can enter either a numeric value in hex format or the equivalent text name. For example, the OID hex format for TCP/IP is: 1.3.6.1.2.1.6 The text format is for TCP/IP is: tcp The following prompt is displayed: Enter View Type [I-Included, E-Excluded]: 8. Choose one of the following view types: I-Included Enter this value to permit the View Name to see the subtree specified above.
AT-S70 Management Software User’s Guide 3. From the SNMPv3 Configurations menu, select Configure SNMPv3 View Table. The Configure SNMPv3 View Table menu is displayed, as shown in Figure 65 on page 160. 4. From the Configure SNMPv3 View Table menu, select Modify SNMPv3 Table Entry. The Modify SNMPv3 Table Entry menu is displayed, as shown in Figure 66 on page 164. 5. To modify the storage type, select Set Storage Type. The following prompt is displayed: Enter View Name: 6.
Chapter 9: SNMPv3 To display the Display SNMPv3 View Table menu, perform the following procedure. 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2. From the System Configuration menu, select SNMPv3 Configurations. The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. 3. From the SNMPv3 Configurations menu, select Configure SNMPv3 View Table.
AT-S70 Management Software User’s Guide Configuring the SNMPv3 Access Table This section contains a description of the SNMPv3 Access Table and how to create, delete, and modify table entries. The SNMPv3 Access Table allows you to configure a security group. Each user must belong to a security group. After you have configured a security group, use the Group Table to assign users to security groups. Refer to “Creating an SNMPv3 Group Table Entry” on page 186.
Chapter 9: SNMPv3 The Configure SNMPv3 Access Table menu is displayed, as shown in Figure 68. Configure SNMPv3 Access Table Converteon Create SNMPv3 Table Entry Delete SNMPv3 Table Entry Modify SNMPv3 Table Entry Display SNMPv3 Table Entry Return to SNMPv3 Configurations ... Figure 68. Configure SNMPv3 Access Table Menu 4. To create a group in the SNMPv3 Access Table, select Create SNMPv3 Table Entry. The following prompt is displayed: Enter Group Name: 5. Enter a descriptive name of the group.
AT-S70 Management Software User’s Guide 6. Select one of the following SNMP protocols as the Security Model for this Group Name. 1-v1 Select this value to associate the Group Name with the SNMPv1 protocol. 2-v2c Select this value to associate the Group Name with the SNMPv2c protocol. 3-v3 Select this value to associate the Group Name with the SNMPv3 protocol. The SNMPv3 protocol allows you to configure the group to authenticate SNMPv3 entities (users) and encrypt messages.
Chapter 9: SNMPv3 8. Enter a value that you configured with the View Name parameter in the SNMPv3 View Table. A Read View Name allows the users assigned to this Group Name to view the information specified by the View Table entry. This value does not need to be unique. The following prompt is displayed: Enter Write View Name: 9. Enter a value that you configured with the View Name parameter in the SNMPv3 View Table.
AT-S70 Management Software User’s Guide 14. From the System Configuration Menu, select Save Configuration File. Deleting an SNMPv3 Access Table Entry You may want to delete an entry from the SNMPv3 Access Table. After you delete an SNMPv3 Access Table, there is no way to undelete, or recover, the entry. To delete an entry in the SNMPv3 Access Table, perform the following procedure: 1. From the Main Menu, select System Configuration.
Chapter 9: SNMPv3 3-v3 Select this value to associate the Group Name with the SNMPv3 protocol. The following prompt is displayed: Enter Security Level [A-AuthNoPriv, P-AuthPriv, NNoauthNoPriv]: 7. Enter the Security Level of this Group Name. Select one of the following Security Levels: A-AuthNoPriv This option represents authentication, but no privacy protocol. Select this security level if you want to authenticate SNMP users, but you do not want to encrypt messages using a privacy protocol.
AT-S70 Management Software User’s Guide Modifying an SNMPv3 Access Table Entry This section describes how to modify parameters in an SNMPv3 Access Table entry. For each entry in the SNMPv3 Access Table, you can modify the following parameters: Read View Name Write View Name Notify View Name Storage Type Configure the values of the Read View Name, Write View Name, and Notify View Name parameters with values previously configured with the View Name parameter in the SNMPv3 View Table.
Chapter 9: SNMPv3 The Modify SNMPv3 Table Entry menu is displayed, as shown in Figure 69. Converteon Configure SNMPv3 Access Table Modify SNMPv3 Table Entry Set Set Set Set Read View Name Write View Name Notify View Name Storage Type Return to SNMPv3 Access Table ... Figure 69. Modify SNMPv3 Table Entry Menu 5. To modify the Read View Name parameter, select Set Read View Name. The following prompt is displayed: Enter Group Name: 6. Enter a Group Name that was previously configured.
AT-S70 Management Software User’s Guide 8. Select one of the following security levels: A-AuthNoPriv This option represents authentication, but no privacy protocol. Select this security level if you want to authenticate SNMP users, but you do not want to encrypt messages using a privacy protocol.You can select this value if you configured the Security Model parameter with the SNMPv3 protocol. P-AuthPriv This option represents authentication and the privacy protocol.
Chapter 9: SNMPv3 Modifying the Write View Name To modify the Write View Name parameter in an SNMPv3 Access Table entry, perform the following procedure. 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2. From the System Configuration menu, select SNMPv3 Configurations. The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. 3. From the SNMPv3 Configurations menu, select Configure SNMPv3 Access Table.
AT-S70 Management Software User’s Guide 3-v3 Select this value to associate the Group Name with the SNMPv3 protocol. The following prompt is displayed: Enter Security Level [A-AuthNoPriv, P-AuthPriv, NNoauthNoPriv]: 8. Enter the Security Level configured for this Group Name. You cannot change the value of the Security Level parameter. Select one of the following security levels: A-AuthNoPriv This option represents authentication, but no privacy protocol.
Chapter 9: SNMPv3 The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 11. From the System Configuration Menu, select Save Configuration File. Modifying the Notify View Name To modify the Notify View Name parameter in an SNMPv3 Access Table entry, perform the following procedure. 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2. From the System Configuration menu, select SNMPv3 Configurations.
AT-S70 Management Software User’s Guide 1-v1 Select this value to associate the Group Name with the SNMPv1 protocol. 2-v2c Select this value to associate the Group Name with the SNMPv2c protocol. 3-v3 Select this value to associate the Group Name with the SNMPv3 protocol. The following prompt is displayed: Enter Security Level [A-AuthNoPriv, P-AuthPriv, NNoauthNoPriv]: 8. Enter the Security Level configured for this Group Name. You cannot change the value of the Security Level parameter.
Chapter 9: SNMPv3 A Notify View Name permits the users assigned to this Security Group to send traps specified in this view of the MIB tree. This value does not need to be unique. 10. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 11. From the System Configuration Menu, select Save Configuration File.
AT-S70 Management Software User’s Guide 7. Enter the Security Model configured for this Group Name. You cannot change the value of the Security Model parameter. Select one of the following SNMP protocols: 1-v1 Select this value to associate the Group Name with the SNMPv1 protocol. 2-v2c Select this value to associate the Group Name with the SNMPv2c protocol. 3-v3 Select this value to associate the Group Name with the SNMPv3 protocol.
Chapter 9: SNMPv3 Note If you have selected SNMPv1 or SNMPv2c, N-NoauthNoPriv is the only security level you can select. Enter Storage Type [V-Volatile, N-NonVolatile]: 9. Select one of the following storage types for this table entry: V-Volatile Select this storage type if you do not want the ability to save an entry in the SNMPv3 Access Table to the configuration file. N-NonVolatile Select this storage type if you want the ability to save an entry in the SNMPv3 Access Table to the configuration file.
AT-S70 Management Software User’s Guide The Snmpv3 Access Info menu is displayed, as shown in Figure 70. Converteon SNMPv3 Access Info: Group Name ................... Context Prefix ............... Security Model................ Security Level ............... Context Match ................ Read View .................... Write View.................... Notify View .................. Storage Type ................. Row Status ...................
Chapter 9: SNMPv3 Configuring the SNMPv3 Group Table This section contains a description of the SNMPv3 Group Table and how to create, delete, and modify table entries. The SNMPv3 Group Table allows you to associate a User Name with a Group Name. The User Name is configured in the Configure SNMPv3 User Table menu while the Group Name is configured in the Configure SNMPv3 Access Table menu.
AT-S70 Management Software User’s Guide The Configure SNMPv3 Group Table menu is displayed, as shown in Figure 71. Configure SNMPv3 Group Table Converteon Create SNMPv3 Table Entry Delete SNMPv3 Table Entry Modify SNMPv3 Table Entry Display SNMPv3 Table Entry Return to SNMPv3 Configurations ... Figure 71. Configure SNMPv3 Group Table Menu 4. To configure a group in the SNMPv3 Group Table, select Create SNMPv3 Table Entry. The following prompt is displayed: Enter Security Name: 5.
Chapter 9: SNMPv3 7. Enter a Group Name that you configured in the SNMPv3 Access Table. Refer to “Creating an SNMPv3 Access Table Entry” on page 169. There are four default values for this field: defaultV1GroupReadOnly defaultV1GroupReadWrite defaultV2cGroupReadOnly defaultV2cGroupReadWrite These values are reserved for SNMPv1 and SNMPv2c implementations. The following prompt is displayed: Enter Storage Type [V-Volatile, N-NonVolatile]: 8.
AT-S70 Management Software User’s Guide The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2. From the System Configuration menu, select SNMPv3 Configurations. The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. 3. From the SNMPv3 Configurations menu, select Configure SNMPv3 Group Table. The Configure SNMPv3 Group Table menu is displayed, as shown in Figure 71 on page 187.
Chapter 9: SNMPv3 7. Enter Y to delete this SNMPv3 Group table entry or N to save the Group table entry. 8. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 9. From the System Configuration Menu, select Save Configuration File. Modifying an SNMPv3 Group Table Entry This section describes how to modify parameters in an SNMPv3 Group Table entry.
AT-S70 Management Software User’s Guide The Modify SNMPv3 Group Table is displayed as shown in Figure 72. Converteon Configure SNMPv3 Group Table Modify SNMPv3 Table Entry Set Group Name Set Storage Type Return to Configure SNMPv3 Group Table ... Figure 72. Modify SNMPv3 Group Table Menu 5. To modify the Group Name, select Set Group Name. The following prompt is displayed: Enter User (Security) Name: 6. Enter a User Name.
Chapter 9: SNMPv3 This value must match a value configured in the Group Name parameter in the Configure SNMPv3 Access Table. Refer to “Creating an SNMPv3 Access Table Entry” on page 169. 9. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 10. From the System Configuration Menu, select Save Configuration File. Modifying the Storage Type To modify the Storage Type in an SNMPv3 Group Table entry, perform the following procedure. 1.
AT-S70 Management Software User’s Guide The following prompt is displayed: Enter Security Model [1-v1, 2-v2c, 3-v3]: 7. Enter the Security Model configured for this User Name. You cannot change the value of the Security Model parameter. Select one of the following SNMP protocols: 1-v1 Select this value if this User Name is configured with the SNMPv1 protocol. 2-v2c Select this value if this User Name is configured with the SNMPv2c protocol.
Chapter 9: SNMPv3 The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2. From the System Configuration menu, select SNMPv3 Configurations. The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. 3. From the SNMPv3 Configurations menu, select Configure SNMPv3 Group Table. The Configure SNMPv3 Group Table menu is displayed, as shown in Figure 71 on page 187. 4. From the Configure SNMPv3 Group Table menu, select Display SNMPv3 Table Entry.
AT-S70 Management Software User’s Guide Configuring the SNMPv3 Notify Table This section contains a description of the SNMPv3 Notify Table menu and how to create, delete, and modify table entries. The Configure SNMPv3 Notify Table menu allows you to define a name for sending traps. For each Notify Name, you define if a trap or inform message ia sent. The two message types, trap and inform, have different packet formats.
Chapter 9: SNMPv3 The Configure SNMPv3 Notify Table menu is displayed, as shown in Figure 74. Configure SNMPv3 Notify Table Converteon Create SNMPv3 Table Entry Delete SNMPv3 Table Entry Modify SNMPv3 Table Entry Display SNMPv3 Table Entry Return to SNMPv3 Configurations ... Figure 74. Configure SNMPv3 Notify Table Menu 4. To create an entry in the table, select Create SNMPv3 Table Entry. The following prompt is displayed: Enter Notify Name: 5. Enter the name associated with this trap message.
AT-S70 Management Software User’s Guide 8. Select one of the following storage types for this table entry: V-Volatile Select this storage type if you do not want the ability to save an entry in the SNMPv3 Notify Table to the configuration file. N-NonVolatile Select this storage type if you want the ability to save an entry in the SNMPv3 Notify Table to the configuration file. Allied Telesis recommends this storage type.
Chapter 9: SNMPv3 Note To display a Group Name and its associated parameters from the Configure SNMPv3 Group Table menu, type N to display the Next Page and P to display the previous page. 4. To delete an SNMPv3 Notify Table entry, select Delete SNMPv3 Table Entry. The following prompt is displayed: Enter Notify Name: 5. Enter a Notify Name. The following prompt is displayed: Do you want to Delete this table entry? (Yes or No): 6. Enter Y to delete the selected table entry or N to save the entry. 7.
AT-S70 Management Software User’s Guide The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. 3. From the SNMPv3 Configurations menu, select Configure SNMPv3 Notify Table. The Configure SNMPv3 Notify Table menu is displayed, as shown in Figure 74 on page 196. 4. From the Configure SNMPv3 Notify Table menu, select Modify SNMPv3 Table Entry. The Modify SNMPv3 Notify Table menu is displayed, as shown in Figure 75.
Chapter 9: SNMPv3 The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 9. From the System Configuration Menu, select Save Configuration File. Modifying a Notify Type To modify the Notify Type parameter in an SNMPv3 Notify Table entry, perform the following procedure. 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2. From the System Configuration menu, select SNMPv3 Configurations.
AT-S70 Management Software User’s Guide I-Inform Indicates this notify table is used to send inform messages. With this message type, the switch expects a response from the host. 8. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 9. From the System Configuration Menu, select Save Configuration File. Modifying a Storage Type To modify the Storage Type parameter in an SNMPv3 Notify Table entry, perform the following procedure. 1.
Chapter 9: SNMPv3 V-Volatile Select this storage type if you do not want the ability to save an entry in the SNMPv3 Notify Table to the configuration file. N-NonVolatile Select this storage type if you want the ability to save an entry in the SNMPv3 Notify Table to the configuration file. Allied Telesis recommends this storage type. 8. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 9.
AT-S70 Management Software User’s Guide The Configure SNMPv3 Notify Table is displayed, as shown in Figure 76. Configure SNMPv3 Notify Table Notify Name ................... Notify Tag .................... Notify Type.................... Storage Type .................. Row Status .................... sysadminTrap sysadminTag Trap NonVolatile Active N - Next Entry, P - Prev Entry, F - First Entry, R - Return Figure 76.
Chapter 9: SNMPv3 Configuring the SNMPv3 Target Address Table This section contains a description of the SNMPv3 Target Address Table menu and how to create, delete, and modify table entries. You use the SNMPv3 Target Address Table menu to assign the IP address of a host that is used for generating notifications. The Configure SNMPv3 Target Address Table menu is linked internally to the Configure SNMPv3 Notify Table through the Tag List parameter.
AT-S70 Management Software User’s Guide The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. 3. From the Configure SNMPv3 User Table menu, select Configure SNMPv3 Target Address Table. The Configure SNMPv3 Target Address Table menu is displayed, as shown in Figure 77. Configure SNMPv3 Target Address Table Converteon Create SNMPv3 Table Entry Delete SNMPv3 Table Entry Modify SNMPv3 Table Entry Display SNMPv3 Table Entry Return to SNMPv3 Configurations ... Figure 77.
Chapter 9: SNMPv3 The following prompt is displayed: Enter Timeout (10mS): [0 to 2147483647]-> 1500 8. Enter a timeout value in milliseconds. When an Inform message is generated, a response from the switch is required. The timeout value determines how long the switch considers the Inform message an active message. This parameter applies to Inform messages only. The range is from 0 to 2,147,483,647 milliseconds. The default value is 1500 milliseconds.
AT-S70 Management Software User’s Guide 12. Select one of the following storage types for this table entry: V-Volatile Select this storage type if you do not want the ability to save an entry in the SNMPv3 Target Address Table to the configuration file. N-NonVolatile Select this storage type if you want the ability to save an entry in the SNMPv3 Target Address Table to the configuration file. Allied Telesis recommends this storage type.
Chapter 9: SNMPv3 Note To display a Group Name and its associated parameters from the Configure SNMPv3 Group Table menu, type N to display the Next Page and P to display the previous page. 4. To delete an SNMPv3 Target Address Table entry, select Delete SNMPv3 Table Entry. The following prompt is displayed: Enter Target Address Name: 5. Enter a Target Address Name. The following prompt is displayed: Do you want to Delete this table entry? (Yes or No): 6.
AT-S70 Management Software User’s Guide 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2. From the System Configuration menu, select SNMPv3 Configurations. The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. 3. From the Configure SNMPv3 User Table menu, select Configure SNMPv3 Target Address Table. The Configure SNMPv3 Target Address Table menu is displayed, as shown in Figure 77 on page 205. 4.
Chapter 9: SNMPv3 The following prompt is displayed: Enter IP Address: 7. Enter the IP address of the host. Use the following format for an IP address: XXX.XXX.XXX.XXX 8. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 9. From the System Configuration Menu, select Save Configuration File.
AT-S70 Management Software User’s Guide This is the name of the SNMP manager, or host, that manages the SNMP activity on your switch. You can enter a name of up to 32 alphanumeric characters. The following prompt is displayed: Enter UDP Port#: [0 to 65535]-> 162 7. Enter a UDP port. You can enter a UDP port in the range of 0 to 65,535. The default UDP port is 162. 8. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 9.
Chapter 9: SNMPv3 5. To modify the Target Address Timeout, select Set Target Address Timeout. The following prompt is displayed: Enter Target Address Name: 6. Enter a previously configured Target Address Name. This is the name of the SNMP manager, or host, that manages the SNMP activity on your switch. You can enter a name of up to 32 alphanumeric characters. The following prompt is displayed: Enter Timeout (10mS): [0 to 2147483647]-> 1500 7. Enter a timeout value in milliseconds.
AT-S70 Management Software User’s Guide 3. From the Configure SNMPv3 User Table menu, select Configure SNMPv3 Target Address Table. The Configure SNMPv3 Target Address Table menu is displayed, as shown in Figure 77 on page 205. 4. From the Configure SNMPv3 Target Address Table menu, select Modify SNMPv3 Table Entry. The Modify SNMPv3 Target Address Table menu is displayed, as shown in Figure 78 on page 209. 5. To modify the Target Address Retries, select Set Target Address Retries.
Chapter 9: SNMPv3 2. From the System Configuration menu, select SNMPv3 Configurations. The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. 3. From the Configure SNMPv3 User Table menu, select Configure SNMPv3 Target Address Table. The Configure SNMPv3 Target Address Table menu is displayed, as shown in Figure 77 on page 205. 4. From the Configure SNMPv3 Target Address Table menu, select Modify SNMPv3 Table Entry.
AT-S70 Management Software User’s Guide Table entry, perform the following procedure. 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2. From the System Configuration menu, select SNMPv3 Configurations. The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. 3. From the Configure SNMPv3 User Table menu, select Configure SNMPv3 Target Address Table.
Chapter 9: SNMPv3 9. From the System Configuration Menu, select Save Configuration File. Modifying the Storage Type To modify the Storage Type parameter in an SNMPv3 Target Address Table entry, perform the following procedure. 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2. From the System Configuration menu, select SNMPv3 Configurations. The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. 3.
AT-S70 Management Software User’s Guide V-Volatile Select this storage type if you do not want the ability to save an entry in the SNMPv3 Target Address Table to the configuration file. N-NonVolatile Select this storage type if you want the ability to save an entry in the SNMPv3 Target Address Table to the configuration file. Allied Telesis recommends this storage type. 8. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 9.
Chapter 9: SNMPv3 The Configure SNMPv3 Target Address Table window is displayed, as shown in Figure 79. Configure SNMPv3 Target Address Table TargetAddress Name ........... host408 TDomain .......................1.3.6.1.6.1.1 TAddress ..................... 198.35.11.1 UDP Port ..................... 162 Timeout....................... 1500 Retries....................... 3 Tag List ..................... sysadminTag Parameters ................... SNMPmgrPC Storage Type .................
AT-S70 Management Software User’s Guide Configuring the SNMPv3 Target Parameters Table This section contains a description of the SNMPv3 Target Parameters Table and how to create, delete, and modify table entries. The SNMPv3 Target Parameters Table links the user security information with the message notification information configured in the Configure SNMPv3 Notify Table menu and Configure SNMPv3 Target Address Table menu.
Chapter 9: SNMPv3 There are three functions you can perform with the Configure SNMPv3 Target Parameters Table menu.
AT-S70 Management Software User’s Guide Enter a value of up to 32 alphanumeric characters. Note You are prompted to enter a value for the Message Processing Model parameter only if you select SNMPv1 or SNMPv2c as the Security Model. If you select the SNMPv3 protocol as the Security Model, then the Message Processing Model is automatically assigned to SNMPv3. The following prompt is displayed: Enter User (Security) Name: 6. Enter a User Name.
Chapter 9: SNMPv3 Note The value you configure for the Security Level must match the value configured for the User Name in the Configure SNMPv3 User Table menu. Refer to “Creating an SNMPv3 User Table Entry” on page 146. A-AuthNoPriv This option represents authentication, but no privacy protocol. Select this security level if you want to authenticate SNMP users, but you do not want to encrypt messages using a privacy protocol.
AT-S70 Management Software User’s Guide 11. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 12. From the System Configuration Menu, select Save Configuration File. Deleting an SNMPv3 Target Parameters Table Entry You may want to delete an entry from the SNMPv3 Target Parameters Table. When you delete an SNMPv3 Target Parameters Table entry, there is no way to undelete, or recover, the entry.
Chapter 9: SNMPv3 7. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 8. From the System Configuration Menu, select Save Configuration File. Modifying an SNMPv3 Target Parameters Table Entry This section provides procedures for modifying parameters in an SNMPv3 Target Parameters Table entry. The parameter values configured in the Target Parameters Table must match those configured in the other tables.
AT-S70 Management Software User’s Guide Note You cannot modify an entry in the SNMPv3 Target Parameter Table that contains a value of “default” in the Target Parameters Name field. Modifying the Security Name (User Name) In the AT-S70 implementation of the SNMPv3 protocol, the Security Name and the User Name parameters are equivalent. In the SNMPv3 Target Parameters Table menu, the Security Name and the User Name parameters are used interchangeably.
Chapter 9: SNMPv3 The Modify SNMPv3 Target Parameters Table menu is displayed, as shown in Figure 81. Converteon Configure SNMPv3 Target Parameters Table Modify SNMPv3 Table Entry Set Set Set Set Set Security Name (User Name) Security Model Security Level Message Process Model Storage Type Return to Configure SNMPv3 Target Parameters Table ... Figure 81. Modify SNMPv3 Target Parameters Table Menu 5. To change the Security Name parameter, select Set Security Name.
AT-S70 Management Software User’s Guide Caution If the values of the Security Model parameter in the SNMPv3 User Table and the SNMPv3 Target Parameter Table entry do not match, notification messages are not generated on behalf of this User (Security) Name. To modify the Security Model parameter in an SNMPv3 Target Parameter Table entry, perform the following procedure. 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2.
Chapter 9: SNMPv3 1-v1 Select this value if this User Name is associated with the SNMPv1 protocol. 2-v2c Select this value if this User Name is associated with the SNMPv2c protocol. 3-v3 Select this value if this User Name is associated with the SNMPv3 protocol. 8. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 9. From the System Configuration Menu, select Save Configuration File.
AT-S70 Management Software User’s Guide 5. To modify the Security Level, select Set Security Level. The following prompt is displayed: Enter Target Parameters Name: 6. Enter a previously configured Target Parameters Name. Enter a value of up to 32 alphanumeric characters. The following prompt is displayed: Enter Security Level [A-AuthNoPriv, P-AuthPriv, NNoauthNoPriv]: 7. Enter the Security Level.
Chapter 9: SNMPv3 The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 9. From the System Configuration Menu, select Save Configuration File. Modifying the Message Process Model You can modify the Message Process Model for SNMPv1 and SNMPv2c protocol configurations only. When you configure the SNMPv3 protocol, the Message Process Model is automatically assigned to the SNMPv3 protocol.
AT-S70 Management Software User’s Guide Enter Message Processing Model[1-v1,2-v2c,3-v3]: 7. Select one of the following SNMP protocols that is used to process, or send messages: 1-v1 Select this value to process messages with the SNMPv1 protocol. 2-v2c Select this value to process messages with the Security Name, or User Name, with the SNMPv2c protocol. 3-v3 Select this value to process messages with the SNMPv3 protocol. 8. From the Main Menu, select System Configuration.
Chapter 9: SNMPv3 The following prompt is displayed: Enter Target Parameters Name: 6. Enter a previously configured Target Parameters Name. Enter a value of up to 32 alphanumeric characters. The following prompt is displayed: Enter Storage Type [V-Volatile, N-NonVolatile]: 7. Select one of the following storage types for this table entry: V-Volatile Select this storage type if you do not want the ability to save an entry in the SNMPv3 Target Parameters Table to the configuration file.
AT-S70 Management Software User’s Guide The Configure SNMPv3 Target Parameters Table menu is displayed, as shown in Figure 80 on page 220. 4. From the Configure SNMPv3 User Table menu, select Display SNMPv3 Table Entry. The Snmpv3 Access Info menu is displayed, as shown in Figure 82. Configure SNMPv3 Target Parameters Table Target Parameters Name ....... Message Processing Model...... Security Model................ Security Name ................ Security Level ............... Storage Type .................
Chapter 9: SNMPv3 Saving SNMPv3 Configuration To save the changes made to the SNMPv3 Configuration, perform the following procedure: 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2. From the System Configuration menu, select SNMPv3 Configurations. The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. The following prompt is displayed: Do you want to save SNMPV3 Configuration? (Yes or No): 3.
AT-S70 Management Software User’s Guide Loading SNMPv3 Configuration To load the new changes made to the SNMPv3 Configuration, perform the following procedure: 1. From the Main Menu, select System Configuration. The System Configuration Menu is displayed, as shown in Figure 10 on page 46. 2. From the System Configuration menu, select SNMPv3 Configurations. The SNMPv3 Configurations menu is displayed, as shown in Figure 61 on page 147. 3.
Chapter 9: SNMPv3 236
Chapter 10 File Downloads and Uploads This chapter describes how to download the AT-S70 management software image and configuration updates and contains the following sections: “File Uploads and Downloads Overview” on page 238 “File Upload and Download Guidelines” on page 239 “Downloading the AT-S70 Software Image File” on page 241 “Downloading the Line Card Image and Bootloader Files to a Local Line Card” on page 247 “Downloading or Uploading a Configuration File” on page 257 The foll
Chapter 10: File Downloads and Uploads File Uploads and Downloads Overview The firmware on the Converteon™ chassis consists of the following three parts: AT-S70 management software This is the operating software for the chassis. AT-S70 bootloader This code initially controls the chassis whenever you power ON or reset the chassis. System configuration This contains the settings for the different system parameters.
AT-CV5000 Media Converter Chassis Installation Guide File Upload and Download Guidelines This sections covers the general guidelines that apply to downloading files from both local and remote management sessions. Refer to the sections below for guidelines apply to each management session. General Guidelines Configuration File Guidelines You can download a new AT-S70 image file onto the chassis from either a local or Telnet management session.
Chapter 10: File Downloads and Uploads Local Management Session Guidelines Remote Management Session Guidelines Line Card Image and Bootloader File Guidelines This section contains the guidelines for downloading a new AT-S70 software image file or configuration file onto a chassis from a local management session. Note To download a file through a Telnet management session, refer to “Remote Management Session Guidelines” on page 240.
AT-CV5000 Media Converter Chassis Installation Guide Downloading the AT-S70 Software Image File The AT-S70 software image file is provided in a self-extracting compressed file which also contains several other files. The software image file has an .IMG extension. This is the one to be used in the upgrade procedures. Note There are two different image files used with the Converteon™ products, the image file used to update the software on the management card is “ATS70.
Chapter 10: File Downloads and Uploads The Image Download menu is displayed, as shown in Figure 83.
AT-CV5000 Media Converter Chassis Installation Guide 8. Type Y for to start the download. The following prompt is displayed: Downloading Image through TFTP........... After the system has downloaded the new image, it reboots and begins to initialize the software. The system does not forward any network traffic during the initialization process. Note Wait until the software is initialized before you attempt to reestablish your management session.
Chapter 10: File Downloads and Uploads 6. From the HyperTerminal main window, select the Transfer > Send File, as shown in Figure 84. Figure 84. HyperTerminal Window The Send File window is displayed, as shown in Figure 85. Figure 85. Send File Window 7. Click the Browse button to select the file to be downloaded onto the chassis. 8. In the Protocol field, select the transfer protocol as either Xmodem or 1K Xmodem for a faster download. 9. Click Send.
AT-CV5000 Media Converter Chassis Installation Guide status of the software download. The download process takes several minutes to complete. Figure 86. Xmodem File Send Window If you are downloading a configuration file, the chassis automatically resets once the download is complete. Some network traffic may be lost during the system reset. Caution When downloading a chassis image file, the chassis must initialize it by decompressing it and writing it to FLASH. This requires several minutes to complete.
Chapter 10: File Downloads and Uploads After the download is complete, the HyperTerminal window is displayed with the status message shown in Figure 87. Figure 87. Download Complete Message 10. Press twice to reset the chassis. Some network traffic may be during the system reset. The download process is complete once the chassis has completed its reset. The new AT-S70 image file or configuration file is now active on the chassis. 11.
AT-CV5000 Media Converter Chassis Installation Guide Downloading the Line Card Image and Bootloader Files to a Local Line Card This section contains the following subsections: Downloading the Line Card Image File “Downloading the Line Card Image File,” next “Downloading the Line Card Bootloader File” on page 249 You can download the line card image file using Xmodem or TFTP, as described in the following procedures: “Downloading the Line Card Image File Using Xmodem,” next “Downloading the
Chapter 10: File Downloads and Uploads 6. Enter the slot number of the line card to be upgraded. 7. Press . The following prompt is displayed: Ready to download linecard image..... 8. Begin the image file transfer of the new management software image. Note The transfer protocol must be Xmodem or 1K Xmodem. 9. For an example of how to download the file using the Hilgraeve HyperTerminal program, refer to steps 6 to 12 in “Downloading the AT-S70 Software Image File Using Xmodem” on page 243.
AT-CV5000 Media Converter Chassis Installation Guide 8. Enter the filename of the image file stored on the TFTP server. 9. Press . The following prompt is displayed: Ready to download application image through TFTP. Warning: During Image Download Management activity is disabled. Do TFTP download now? (Yes or No): 10. Type Y for to start the download. The following prompt is displayed: Downloading Image through TFTP......1298 TFTP: Received 664120 bytes in 9.5 seconds Verifying Checksum....
Chapter 10: File Downloads and Uploads The following prompt is displayed: Ready to download application image via XModem. Warning: During Image Download Management activity is disabled. Do XMODEM download now? (Yes or No): 4. Enter Y to start the download process or N to cancel. 5. If you enter Y, the following prompt is displayed: Ready to download application image via XModem. Warning: During Image Download Management activity is disabled. Do XMODEM download now? (Yes or No): Linecard Slot Number: 6.
AT-CV5000 Media Converter Chassis Installation Guide The following prompt is displayed: Enter LineCard Slotnum: -> 4. Enter the slot number of the line card to be upgraded. 5. Press . The following prompt is displayed: TFTP Server IP Address-> 6. Enter the IP address of the TFTP server. 7. Press . The following prompt is displayed: Image File Name-> 8. Enter the filename of the image file stored on the TFTP server. 9. Press .
Chapter 10: File Downloads and Uploads Downloading the Line Card Image and Bootloader Files to a Remote Line Card This section contains the following subsections: Downloading the Line Card Image File to a Remote Line Card “Downloading the Line Card Image File,” next “Downloading the Line Card Bootloader File” on page 249 You can download the line card image file using Xmodem or TFTP, as described in the following procedures: “Downloading the Line Card Image File Using Xmodem,” next “Downlo
AT-CV5000 Media Converter Chassis Installation Guide 6. Enter the slot number of the line card to be upgraded. 7. Press . The following prompt is displayed: Ready to download linecard image..... 8. Begin the image file transfer of the new management software image. Note The transfer protocol must be Xmodem or 1K Xmodem. 9.
Chapter 10: File Downloads and Uploads 8. Enter the filename of the image file stored on the TFTP server. 9. Press . The following prompt is displayed: Ready to download application image through TFTP. Warning: During Image Download Management activity is disabled. Do TFTP download now? (Yes or No): 10. Type Y for to start the download. The following prompt is displayed: Downloading Image through TFTP......1298 TFTP: Received 664120 bytes in 9.5 seconds Verifying Checksum....
AT-CV5000 Media Converter Chassis Installation Guide The following prompt is displayed: Ready to download application image via XModem. Warning: During Image Download Management activity is disabled. Do XMODEM download now? (Yes or No): 4. Enter Y to start the download process or N to cancel. 5. If you enter Y, the following prompt is displayed: Ready to download application image via XModem. Warning: During Image Download Management activity is disabled.
Chapter 10: File Downloads and Uploads The following prompt is displayed: Enter LineCard Slotnum: -> 4. Enter the slot number of the line card to be upgraded. 5. Press . The following prompt is displayed: TFTP Server IP Address-> 6. Enter the IP address of the TFTP server. 7. Press . The following prompt is displayed: Image File Name-> 8. Enter the filename of the image file stored on the TFTP server. 9. Press .
AT-CV5000 Media Converter Chassis Installation Guide Downloading or Uploading a Configuration File When an AT-CV5M01 Management Card is replaced, all the parameter settings saved on the Management Card are gone. To keep the current parameter settings, make sure to upload the configuration file onto your computer or laptop before replacing the AT-CV5M01 Management Card. After a new AT-CV5M01 Management Card is installed, you can download the configuration file onto the new card.
Chapter 10: File Downloads and Uploads The following prompt is displayed: Ready to download configuration file through TFTP. Warning: During Download Configuration Management activity is disabled. Do TFTP download now? (Yes or No): 8. Type Y to start the download. The following prompt is displayed: Downloading Configuration file through TFTP, please wait ... After the system has downloaded the new configuration file, it reboots the system and begins to initialize the software.
AT-CV5000 Media Converter Chassis Installation Guide Configuration File Name-> _ 6. Enter the filename of the configuration file that is to be stored as on the TFTP server. 7. Press . The following prompt is displayed: Ready to upload Configuration file through TFTP. Warning: During Upload Configuration Management activity is disabled. Do TFTP upload now? (Yes or No): 8. Type Y for to start the download. The following prompt is displayed: Uploading Configuration file through TFTP, please wait ..
Chapter 10: File Downloads and Uploads 260
Appendix A AT-S70 Default Settings The following lists the AT-S70 factory default settings. Settings Default IP Address 10.0.0.1 Subnet Mask 255.255.252.0 Gateway Address 0.0.0.
Appendix A: AT-S70 Default Settings Settings Default Threshold Maximum Temperature Threshold 262 60
Appendix B DIP Switch Settings This appendix contains the following information about the DIP switch settings on the Converteon™ line cards: “DIP Switch Features” on page 264 “AT-CV10x Series Line Cards DIP Switches” on page 266 “AT-CM20x and AT-CM212x/1 Series Line Cards DIP Switches” on page 268 “AT-CM2K0S Line Card DIP Switches” on page 270 “AT-CV1KSS Line Card DIP Switches” on page 271 “AT-CM70S Line Card DIP Switch” on page 272 Note If you disable the Line Card DIP Switch Mode
Appendix B: DIP Switch Settings DIP Switch Features All Converteon™ line cards support Link Test, while other DIP switches on the line cards support the following features: MissingLink™ Mode Smart MissingLink Mode OAM Capability (AT-CM2K0S and AT-CM70S Converteon™ line cards only) For detailed information about the DIP switches for a specific Converteon™ line card, refer to the following sections: Link Test “AT-CV10x Series Line Cards DIP Switches” on page 266 “AT-CM20x and AT-CM212x/1
AT-S70 Management Software User’s Guide Note Smart MissingLink is supported on all Converteon™ line cards except the AT-CM70S. OAM OAM refers to the tools and utilities to install, monitor, test, and troubleshoot a network, helping carriers run their networks more efficiently. Note OAM is supported only on the AT-CM20x Series, AT-CM212x/1 Series, AT-CM2K0S, and the AT-CM70S Converteon™ line cards.
Appendix B: DIP Switch Settings AT-CV10x Series Line Cards DIP Switches The AT-CV10x series line cards feature two sets of DIP switches labeled “SW1” and “SW 2” as shown in Figure 90. ON SW1 SW2 1 2 3 4 SW 2 DIP Switch Set SW 1 DIP Switch Set 1 2 3 4 ON 1 2 3 4 1 2 3 4 AT-C M 202 LK AT T X M Figure 88. DIP Switch Sets on an AT-CV10x Series Line Card The DIP switches in the SW 1 DIP switch set allow you to set the operating mode of the line card.
AT-S70 Management Software User’s Guide Table 5 shows how to configure the MDI/MDI-X feature on the twisted pair port of an AT-CV10x Series line card by setting the DIP switches in the SW 2 DIP switch set. Table 5.
Appendix B: DIP Switch Settings AT-CM20x and AT-CM212x/1 Series Line Cards DIP Switches The AT-CM2xx series line cards feature two sets of DIP switches labeled “SW1” and “SW 2” as shown in Figure 89. ON SW 1 DIP Switch Set SW1 SW2 1 2 3 4 ON 1 2 3 4 SW 2 DIP Switch Set 1 2 3 4 1 2 3 4 AT-C M 202 LK Figure 89. DIP Switch Sets on an AT-CM2xx Series Line Card The DIP switches in the SW 1 DIP switch set allow you to set the operating mode of the line card.
AT-S70 Management Software User’s Guide Table 7 shows how to configure the MDI/MDI-X feature on the twisted pair port of an AT-CM20x Series or AT-CM212x/1 Series line card by setting the DIP switches in the SW 2 DIP switch set.. Table 7.
Appendix B: DIP Switch Settings AT-CM2K0S Line Card DIP Switches The AT-CM2K0S line card features one set of DIP switches labeled “SW1” as shown in Figure 90. SW 1 DIP Switch Set SW1 ON AT-C M 2K0 S LK AT SFP Figure 90. DIP Switch Set on an AT-CM2K0S Line Card The DIP switches in the SW 1 DIP switch set allow you to set the operating mode of the line card. For information about the operating modes, refer to “Configuring the Line Card Operating Mode” on page 67.
AT-S70 Management Software User’s Guide AT-CV1KSS Line Card DIP Switches The AT-CV1KSS line card features one set of DIP switches labeled “SW1”, as shown in Figure 91. 2 1 4 3 3 4 1 2 SW1 SW 1 DIP Switch Set ON AT-C V 1KS LK S AT S F P Figure 91. DIP Switch Set on an AT-CV1KSS Line Card The DIP switches in the SW 1 DIP switch set allow you to set the operating mode of the line card. For information about the operating modes, refer to “Configuring the Line Card Operating Mode” on page 67.
Appendix B: DIP Switch Settings AT-CM70S Line Card DIP Switch The AT-CM70S line card features one set of DIP switches located on the base board and labeled “SW1”, as shown in Figure 92. 1 O N 2 SW 1 DIP Switch Set AT-C M7 LK OA M 0S T1/E1 S F P 1 Figure 92. DIP Switch Set on an AT-CM70S Line Card The DIP switches in the SW 1 DIP switch set allow you to set the operating mode of the line card.
Appendix C SNMPv3 Configuration Examples This appendix provides two examples of SNMPv3 configuration using the SNMPv3 Table menus. In addition, a worksheet is provided which you can use as an aid when configuring the SNMPv3 protocol.
Appendix C: SNMPv3 Configuration Examples Configure SNMPv3 View Table Menu View Name: internet View Subtree OID: .1.3.6.1.2.1.
AT-S70 Management Software User’s Guide Configure SNMPv3 Target Address Table Target Address Name: host408 Ip Address: 198.35.11.
Appendix C: SNMPv3 Configuration Examples Storage Type: NonVolatile Configure SNMPv3 Access Table Group Name: Operators Security Model: SNMPv3 Security Level: Authentication Read View Name: internet Write View Name: Notify View Name: 276
AT-S70 Management Software User’s Guide SNMPv3 Worksheet This section provides a table that you can use as a worksheet when configuring SNMPv3. Each SNMPv3 Table is listed with its associated parameters.
Appendix C: SNMPv3 Configuration Examples SNMPv3 Parameters (Continued) SNMPv3 Notify Table Menu Notify Name Notify Tag Notify Type Storage Type SNMPv3 Target Address Table Menu Target Address Name Ip Address UDP Port# Timeout (10ms) Retries Tag List Target Parameters Storage Type SNMPv3 Target Parameters Table Menu Target Parameters Name User (Security) Name Security Model Security Level Storage Type 278
Appendix D Rate Limiting on the AT-CM2K0S Line Card Due to the hardware component design of the AT-CM2K0S line card, the rate limit you specify (see “Setting the Port Ingress and Egress Rate Limits” on page 88) may not be the same as the actual value used by the hardware. For example, when you specify a value between 150,000 and 250,000, the actual value for all settings in that range is 285,714.
Appendix D: Rate Limiting on the AT-CM2K0S Line Card Table 11.
AT-S70 Management Software User’s Guide Table 11.
Appendix D: Rate Limiting on the AT-CM2K0S Line Card Table 11.
AT-S70 Management Software User’s Guide Table 11.
Appendix D: Rate Limiting on the AT-CM2K0S Line Card Table 11.
AT-S70 Management Software User’s Guide Table 11.
Appendix D: Rate Limiting on the AT-CM2K0S Line Card Table 11.
AT-S70 Management Software User’s Guide Table 11.
Appendix D: Rate Limiting on the AT-CM2K0S Line Card Table 11.
AT-S70 Management Software User’s Guide Table 11.
Appendix D: Rate Limiting on the AT-CM2K0S Line Card Table 11.
AT-S70 Management Software User’s Guide Table 11.
Appendix D: Rate Limiting on the AT-CM2K0S Line Card Table 11.
AT-S70 Management Software User’s Guide Table 11.
Appendix D: Rate Limiting on the AT-CM2K0S Line Card Table 11.
AT-S70 Management Software User’s Guide Table 11.
Appendix D: Rate Limiting on the AT-CM2K0S Line Card Table 11.
AT-S70 Management Software User’s Guide Table 11.
Appendix D: Rate Limiting on the AT-CM2K0S Line Card 298
Index A activity log described 92 displaying 93 starting and stopping 93 activity log messages 93 activity monitor 92 AT-CM70S line card local console settings 74 status, displaying 72 TDM port, configuring 75 UART setting, configuring 80 AT-CV5M01 Management Card redundant 83 redundant switchover 83 status, displaying 82 AT-S70 management software downloading using TFTP 241 using Xmodem 243 factory default settings 261 C chassis date and time, configuring 30 diagnostics 94 name, configuring 30 temperatur
Index local management session described 17 starting 23 local OAM information, displaying 120 loopback control OAMPDUs 114 M management access levels 20 management access, configuring 50 management IP addresses, configuring 35 management session local described 17 starting 23 remote described 18 SNMP 19 manager password, configuring 46 maximum frame size, configuring on AT-CM2KOS line card 85 MD5 authentication protocol 136 menus navigation 22 MIB subtree view 138 MIB tree diagram 138 RFC 138 MIB variable
AT-S70 Management Software User’s Guide message notification 139 MIB views 138 overview 136 privacy protocols 137 SNMPv3 Access Table 142 SNMPv3 Notify Table 143 SNMPv3 SecurityToGroup Table 143 SNMPv3 Target Address Table 143 SNMPv3 Target Parameters Table 143 storage types 139 tables 140 User Table 142 View Table 142 SNMPv3 SecurityToGroup Table entry creating 186 deleting 188 displaying 193 modifying group name 190 storage type 192 SNMPv3 SecurityToGroup Table, described 143 SNMPv3 Target Address Table
Index 302
