Wireless Access Point AT-WA7400 Installation Guide PN 613-000487 RevA
Copyright © 2006 Allied Telesyn, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn, Inc.
Electrical Safety and Emissions Standards Standards: This product meets the following standards. U.S. Federal Communications Commission Declaration of Conformity Manufacturer Name: Declares that the product: Model Numbers: Allied Telesyn, Inc. Wireless Access Point AT-WA7400 This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules.
Industry Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
AT-WA7400 Wireless Access Point Installation Guide Translated Safety Statements Important: When you see the , go to the Allied Telesyn website www.alliedtelesyn.com for the translated safety statement in your language.
Contents Electrical Safety and Emissions Standards .............................3 Safety and Electromagnetic Emissions Certifications ...................4 Translated Safety Statements .......................................................5 Preface .......................................................................................13 Safety Symbols Used in this Guide .............................................14 Where to Find Web-based Guides ..............................................
Contents Powering On the Access Point ....................................................38 Running KickStart to Find Access Points on the Network ...........40 Installing KickStart on the Administrator’s PC .....................47 Warranty Registration..................................................................54 Chapter 3: Troubleshooting ....................................................55 Appendix A: Technical Specifications ...................................57 Physical Specifications ........
Figures Figure 1: AT-WA7400 Wireless Access Point21 Figure 2: Front and Back Panels22 Figure 3: Location of the Antenna Connectors31 Figure 4: Attaching the Antennas32 Figure 5: Attaching the Rubber Feet33 Figure 6: Aligning the Access Point for Mounting on the Wall35 Figure 7: Attaching the Magnets36 Figure 8: Attaching the LAN Cable37 Figure 9: Connecting the Power Adapter38 Figure 10: PoE Connection39 Figure 11: AT-WA7400 CD Main Page41 Figure 12: KickStart Page42 Figure 13: KickStart Welcome Page43 Fig
Contents 10
Tables Table 1. Table 2. Table 3. Table 4.
Tables 12
Preface This guide contains instructions on how to install the AT-WA7400 Wireless Access Point.
Preface Safety Symbols Used in this Guide This document uses the safety symbols defined in Table 1. Table 1. Safety Symbols Symbol 14 Meaning Description Caution Performing or omitting a specific action may result in equipment damage or loss of data. Warning Performing or omitting a specific action may result in electrical shock.
AT-WA7400 Wireless Access Point Installation Guide Where to Find Web-based Guides The installation and user guides for all Allied Telesyn products are available in portable document format (PDF) on our web site at www.alliedtelesyn.com. You can view the documents online or download them onto a local workstation or server.
Preface Contacting Allied Telesyn This section provides Allied Telesyn contact information for technical support as well as sales and corporate information. Online Support You can request technical support online by accessing the Allied Telesyn Knowledge Base: http://kb.alliedtelesyn.com. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions.
AT-WA7400 Wireless Access Point Installation Guide Allied Telesyn web site: www.alliedtelesyn.com Allied Telesyn FTP server: ftp://ftp.alliedtelesyn.com If you prefer to download new software from the Allied Telesyn FTP server from your workstation’s command prompt, you will need FTP client software and you must log in to the server. Enter “anonymous” for the user name and your email address for the password.
Preface 18
Chapter 1 Overview The AT-WA7400 Wireless Access Point is a wireless communications hub for devices on your network. It provides continuous, high-speed access between your wireless and Ethernet devices. You administer the AT-WA7400 Wireless Access Point using the AT-WA7400 management software.
Chapter 1: Overview Features The features of the AT-WA7400 Wireless Access Point include: High performance 54 Mbps data rate (802.11g - 802.11a with an upgrade as described in Appendix A, “Radio Bands” on page 59.) Security support via 802.11i (WPA2), WPA-PSK, TKIP, AES, IEEE 802.1x, and EAP/802.1 Multiple BSSID and Virtual LAN (VLANs) Inhibit SSID broadcast and Ignore SSID scan MAC Access Control for wireless interface Load balancing 802.
AT-WA7400 Wireless Access Point Installation Guide Front and Back Panels Figure 1 shows the AT-WA7400 Wireless Access Point. 301 Figure 1.
Chapter 1: Overview Figure 2 shows the front and back panels of the wireless access point. System LEDs LAN LEDs Wireless LEDs RESET TO DEFAULT 5V,2.8A LAN Reset Button Power Connector LAN Port Antenna Connectors Figure 2.
AT-WA7400 Wireless Access Point Installation Guide LEDs The system LEDs on the AT-WA7400 Wireless Access Point are described in Table 2. Table 2. System LEDs LED Power Test State Description Off The access point is not receiving power. Green The access point is receiving power. Off No system maintenance in progress. Amber System startup or maintenance in progress. The LAN LEDs are described in Table 3. Table 3.
Chapter 1: Overview Table 3. LAN LEDs (Continued) LED State Description Off The access point is not operating at 10 Mbps. Blinking The access point is sending or receiving data at 10 Mbps. The Wireless LEDs are described in Table 4. Table 4. Wireless LEDs LED LNK/ACT (WLAN a) LNK/ACT (WLAN g) 24 State Description Off No link is detected. Green An 802.11a WLAN link has been made. Blinking Green Network activity is occurring. Off No link is detected. Green An 802.
Chapter 2 Installation This chapter contains the following sections: “Reviewing Safety Precautions” on page 26 “Installation Guidelines” on page 28 “Unpacking the Access Point” on page 30 “Installing the Antennas” on page 31 “Using the Access Point on a Desktop” on page 33 “Mounting an Access Point on a Wall” on page 34 “Mounting the Access Point on a Metal Surface” on page 36 “Powering On the Access Point” on page 38 “Running KickStart to Find Access Points on the Network” on page 40
Chapter 2: Installation Reviewing Safety Precautions Please review the following safety precautions before you begin to install the AT-WA7400 Wireless Access Point. Note When you see the , go to the Allied Telesyn web site for translated safety statements. Warning: To prevent electric shock, do not remove the cover. No user-serviceable parts inside. This unit contains hazardous voltages and should only be opened by a trained and qualified technician.
AT-WA7400 Wireless Access Point Installation Guide Warning: Operating Temperature. This product is designed for a maximum ambient temperature of 40° degrees C. 9 All Countries: Install product in accordance with local and National Electrical Codes. 10 Caution: Do not install in direct sunlight, or a damp or dusty place.
Chapter 2: Installation Installation Guidelines Allied Telesyn recommends that you have an Allied Telesyncertified RF specialist conduct a site survey to determine the ideal locations for all your Allied Telesyn wireless network devices. To conduct a proper site survey, you need to have special equipment and training. The following general practices should be followed in any installation: Locate access points centrally within areas requiring coverage.
AT-WA7400 Wireless Access Point Installation Guide Microwave Ovens Microwave ovens operate in the same frequency band as 802.11g and 802.11b radios; therefore, if you use a microwave oven within range of your wireless network, you may notice network performance degradation. Both your microwave oven and your wireless network will continue to function, but you may want to consider relocating your microwave oven out of range of your access point. Cordless Telephones If you have an 802.11g or 802.
Chapter 2: Installation Unpacking the Access Point To unpack the AT-WA7400 Wireless Access Point, perform the following procedure: 1. Remove all components from the shipping package. Note Store the packing material in a safe location. You must use the original shipping material if you need to return the unit to Allied Telesyn. 2. Place the access point on a secure, level surface. 3. Ensure that the following hardware components are included in your access point package.
AT-WA7400 Wireless Access Point Installation Guide Installing the Antennas To install the antennas, perform the following procedure: 1. Remove the antennas from their package. 2. Locate the antenna connectors in the back of the AT-WA7400 Wireless Access Point, as shown in Figure 3. 5V,2 .8A RES ET TO DEF AUL T 303 LAN Antenna Connectors Figure 3.
Chapter 2: Installation 3. Screw one antenna into each antenna connector, as shown in Figure 4. 5V,2 .8A RES ET TO DEF AUL T 304 LAN Figure 4. Attaching the Antennas You can point the antennas in the direction that provides the best signal strength.
AT-WA7400 Wireless Access Point Installation Guide Using the Access Point on a Desktop You can place the AT-WA7400 Wireless Access Point on a desktop or other flat surface. To place the AT-WA7400 Wireless Access Point on a desktop, perform the following procedure: 1. Turn the access point over so that the top is resting on a flat surface. 2. Attach the four rubber feet to the bottom of the access point as shown in Figure 5. LAN 305 5V,2 .8A RES ET TO DEF AUL T Figure 5. Attaching the Rubber Feet 3.
Chapter 2: Installation Mounting an Access Point on a Wall To mount the AT-WA7400 Wireless Access Point on a wall, perform the following procedure: 1. Select a wall location and mark two hole locations for the anchors 98.425 mm (3.875 in.) apart. 2. At the two marked hole locations, pre-drill for the drywall anchors. 3. Install the anchors and drive the screws into the anchors leaving approximately 4.76 mm (.1875 in.) exposed.
AT-WA7400 Wireless Access Point Installation Guide 5V ,2 .8 A R ES ET TO D EF AU LT LA N 4. Align the keyholes on the back with the screw heads, as shown in Figure 6. 307 Figure 6. Aligning the Access Point for Mounting on the Wall 5. Place the keyhole slots on the bottom of the access point over the screw heads. 6. Slide the access point down onto the screw heads so that the access point is securely mounted on the wall. You can install the access point either horizontally or vertically.
Chapter 2: Installation Mounting the Access Point on a Metal Surface To mount the AT-WA7400 Wireless Access Point on a metal surface, perform the following procedure: 1. Select a location for the access point. 2. Turn the access point over and place it on a secure surface. 3. Screw the four magnets into the back of the access point, as shown in Figure 7. LAN 5V,2 .8A RES ET TO DEF AUL T Figure 7. Attaching the Magnets 4. Mount the access point on a metal surface.
AT-WA7400 Wireless Access Point Installation Guide Connecting the Access Point to the LAN To connect the AT-WA7400 Wireless Access Point to the LAN, perform the following procedure: 1. Locate the RJ45 cable in the box. 2. Connect one end of the cable to the LAN. 3. Connect the other end of the cable to the LAN port on the back of the access point, as shown in Figure 8. 5V,2 .8A RES ET TO DEF AUL T 308 LAN Figure 8.
Chapter 2: Installation Powering On the Access Point To power on the access point, perform the following procedure: Warning: Do not work on equipment or cables during periods of lightning activity. 4 Warning: Power cord is used as a disconnection device. To de-energize equipment, disconnect the power cord. 5 1. Do one of the following: a. Plug the power cord on the adapter into the power connector on the back panel, as shown in Figure 9, and plug the power adapter into a wall outlet. 5V,2 .
AT-WA7400 Wireless Access Point Installation Guide b. Plug a LAN cable from a unit that supports PoE into the LAN port, as shown in Figure 10. No other power connection is required. 5V,2 .8A RES ET TO DEF AUL T 308 LAN Figure 10. PoE Connection 2. Verify that the POWER LED is green. If the LED is off, refer to Chapter 3, ”Troubleshooting” on page 55. The access point is now powered on and ready for network operation.
Chapter 2: Installation Running KickStart to Find Access Points on the Network KickStart is an easy-to-use utility for discovering and identifying new AT-WA7400 Wireless Access Points. KickStart scans the network looking for access points, displays ID details on those it finds, and provides access to the AT-WA7400 Management Software. Note KickStart (and the other AT-WA7400 tools) recognizes and configures only AT-WA7400 Wireless Access Points.
AT-WA7400 Wireless Access Point Installation Guide To start the discovery process, perform the following procedure: 1. Do one of the following to create an Ethernet connection between the access point and your computer: Connect one end of an Ethernet cable to the LAN port on the access point and the other end to the same hub where your PC is connected. Connect one end of an Ethernet cable to the LAN port on the access point and the other end of the cable to the Ethernet port on the your PC. 2.
Chapter 2: Installation The KickStart page, as shown in Figure 12, provides two options: Open KickStart and Install KickStart. Figure 12. KickStart Page For information about installing KickStart, refer to “Installing KickStart on the Administrator’s PC” on page 47. Otherwise, continue with this procedure. 4. Click Open KickStart.
AT-WA7400 Wireless Access Point Installation Guide The KickStart Welcome page is displayed, as shown in Figure 13. Figure 13. KickStart Welcome Page 5. Click Next to search for access points.
Chapter 2: Installation Wait for the search to complete, or until KickStart has found your new access points, as shown in Figure 14. Figure 14. KickStart Search Results Page Note The KickStart utility only finds other AT-WA7400 Wireless Access Points. If KickStart does not find the AT-WA7400 Wireless Access Point you just installed, an informational window is displayed with troubleshooting information about your LAN and power connections. 6.
AT-WA7400 Wireless Access Point Installation Guide 7. Verify the MAC addresses against the hardware labels for each access point. This will be especially helpful later in providing or modifying the descriptive Location name for each access point. 8. Click Next. The Administration dialog box opens, as shown in Figure 15. Figure 15. Administration Dialog Box Note KickStart provides a link to the AT-WA7400 management software web pages via the IP address of the first access point of each model.
Chapter 2: Installation After your other access points are configured, you can also link to the AT-WA7400 management software web pages using the IP address for any of the other AT-WA7400 Wireless Access Points, for example http://IPAddressOfAccessPoint. 9. Click Administration. You are prompted for a user name and password, as shown in Figure 16. Figure 16. Login Dialog Box The default user name is “manager” and the default password is “friend.” 10.Enter the user name and password and click OK.
AT-WA7400 Wireless Access Point Installation Guide The Basic Settings page opens, as shown in Figure 17. Figure 17. Basic Settings Page Refer to the AT-WA7400 Management Software User’s Guide for information about how to configure the basic settings. Installing KickStart on the Administrator’s PC To install the KickStart utility on the administrator’s PC, perform the following procedure: 1. Insert the AT-WA7400 Wireless Access Point CD into the CDROM drive on your computer.
Chapter 2: Installation 2. Click KickStart Utility. The KickStart page, as shown in Figure 12 on page 42, provides two options: Open KickStart and Install KickStart. The Open KickStart option is described in “Running KickStart to Find Access Points on the Network” on page 40. 3. Click Install KickStart. The KickStart Setup Wizard dialog box is shown in Figure 18. Figure 18. KickStart Setup Wizard Dialog Box 4. Click Next.
AT-WA7400 Wireless Access Point Installation Guide The Select Installation Folder dialog box is shown in Figure 19. Figure 19. Select Installation Folder Dialog Box 5. Do one of the following: To see how much disk space the files require, click Disk Cost.
Chapter 2: Installation The KickStart Setup Disk Space dialog box is shown in Figure 20. Figure 20. KickStart Setup Disk Space Dialog box Select the drive where you want to install KickStart, and then click OK. Click Browse to select a specific location for the KickStart utility. The Browse for Folder window shows the default folder where the utility will be installed unless you select a different location. If this selection is OK, click OK. Otherwise, select a different folder and click OK. 6.
AT-WA7400 Wireless Access Point Installation Guide The KickStart Setup confirmation dialog box is shown in Figure 21. Figure 21. KickStart Installation Confirmation Dialog Box 7. Click Next to start the installation.
Chapter 2: Installation The Installing KickStart dialog box is shown in Figure 22. Figure 22.
AT-WA7400 Wireless Access Point Installation Guide When the installation is complete, the Installation Complete dialog box is displayed, as shown in Figure 23. Figure 23. KickStart Installation Complete Dialog Box 8. Click Close. You can now run KickStart from the Programs folder under Allied Telesyn.
Chapter 2: Installation Warranty Registration After installing your access point, you can register your product by completing the enclosed warranty card and sending it to Allied Telesyn.
Chapter 3 Troubleshooting If the AT-WA7400 Wireless Access Point is not operating correctly, do one of the following: Press the Reset to Default button once to reboot the access point. You can also reset the access point through the AT-S77 management software. See Chapter 20, “Maintenance and Monitoring” in the AT-WA7400 Management Software User’s Guide. Hold in the Reset to Default button for more than five seconds to restore the factory default settings.
Chapter 3: Troubleshooting 56
Appendix A Technical Specifications Physical Specifications Dimensions: 176.34 mm x 103.62 mm x 23.20 mm (W x D x H) (6.94 in. x 4.07 in. x .91 in.) Weight: 250 g (8.81 oz.) Environmental Specifications Operating Temperature: 0 to 50°C Storage Temperature: -20 to 70°C Operating Humidity: 10 to 90% noncondensing Storage Humidity: 10 to 95% noncondensing Operating Altitude Range: 3,000 m Power Specifications Input Supply Voltage: Power over Ethernet or 5 VDC/2.
Appendix A: Technical Specifications 300 328; EN 301 489 Transmitter EMC; Canada IC; CE Mark emission/ immunity; CE Marked (compliant with RTT&E, EMC, LVD Directives); C-Tick Electrical Safety: 58 UL 60950-1, CSA C22.2 No.
Appendix B Radio Bands Allied Telesyn’s AT-WA7400 Wireless Access Point is capable of operating in the 2.4GHZ (IEEE 802.11g/b) AND in the 5GHZ band (IEEE 802.11a) simultaneously. The access point is shipped with the 802.11g/b radio enabled and is software upgradeable to operate in 802.11g/b and 802.11a. For further information about this upgrade, please contact your Allied Telesyn sales representative. Some of the advantages of the 802.11a option are: Higher performance. 802.
Appendix B: Radio Bands 60
