Operator and Parts Manual Loader Models 495, S495 122011 P3690
Table of Contents - 495 & S495 Loader Table of Contents Introduction..................................................................................................................................4 • Terminology......................................................................................................................4 • Hydraulic (Hose Kit)..........................................................................................................5 Specifications..................................
Introduction - 495 & S495 Loader Introduction Allied by Farm King front-end loaders are backed by years of extensive research. Factory testing simulates specific operations to evaluate durability; days of continuous cycling in raising, twisting and dropping loads using a programmed hydraulic power unit represents years of extreme use. With one of the largest mounting kit application lists in the industry, there is an Allied front-end loader available for nearly every tractor, large or small, new or old.
Safety - 495 & S495 Loader Hydraulic (Hose Kit) Hose Kit “A” Loader powered by the tractor remotes. Consists of four hoses leading from loader tubing to tractor remote couplers Hose Kit “B” Loader operated by an external OC or CC valve that is powered from the tractor remotes. Hose Kit “C” Loader operated by an external valve that is plumbed into the tractor hydraulic system.
Specifications - 495 & S495 Loader Specifications 6
Specifications - 495 & S495 Loader Model number: 495 Mounting height: 36" (nominal) Typical range: 33" - 39" Description Bucket Lift Bore 2.50" 2.50" Rod 1.50" 1.50" Stroke 20.63" 20.63" A - Maximum lift height to pivot point (full height): 130" (11.0') B - Clearance with bucket dumped: 100.4" (8.4') C - Reach at maximum height: 28.2" D - Maximum dump angle: 38° F - Bucket rollback angle: 23.4° G - Digging depth: 5.5" H - Overall height in carry position: 70.7" (5.
Safety - 495 & S495 Loader Safety Safety Instructions Remember, YOU are the key to safety. Good safety practices not only protect you, but also the people around you. Make these practices a working part of your safety program. Be certain that everyone operating this equipment is familiar with the recommended operating and maintenance procedures and follows all the safety precautions. Most accidents can be prevented. Do not risk injury or death by ignoring good safety practices.
Safety - 495 & S495 Loader General Safety Instructions • • • • • • • • • • • • • • • • Have a first-aid kit available for use and know how to use it. Have a fire extinguisher available, stored in a highly visible location, and know how to use it. Wear appropriate protective gear.
Safety - 495 & S495 Loader Safety Decals 10
Safety - 495 & S495 Loader Important Precautions 11
Operation - 495 & S495 Loader Operation Operation General Operating Notes: Refer to tractor Operator's Manual for Operating information on the tractor's hydraulic system. Hydraulic systems using auxiliary valves should have them located for easy reach from the tractor seat. Hoses should be connected in such a manner that pushing forward on valve handles lowers the boom or dumps the bucket Warning Always connect boom hoses to float section.
Operation - 495 & S495 Loader Operating Suggestions for Loading When handling heavy loads, be sure to lower lift arms slowly. This is known as feathering the hydraulic lever. If load is lowered too fast and stopped suddenly, excessive shock loads are created which can damage loader or tractor. When loading bucket, drive straight into material. Attempting to turn tractor while loading bucket can cause damage to both the loader and tractor. Note: Bottom surface of bucket is parallel to line on motion.
Operation - 495 & S495 Loader Operating Suggestions for Backfilling DO THIS When backfilling approach pile with a flat bucket. Leave dirt in bucket. Dumping on each pass wastes time. Backgrade work surface with a loaded bucket. Release all pressure on lift cylinders so full weight of bucket is scraping ground. Use heel of bucket Do not use bucket in dumped position for bulldozing. This will only impose severe shock loading on the bucket cylinders and make it more difficult to maintain a level grade.
Operation - 495 & S495 Loader Attaching the Loader to Your Tractor 1. Postions the tractor as centrally as possible and drive, using lowest gear possible, into the loader frame until hoses can be connected. 2.
Operation - 495 & S495 Loader 7. Continue to drive the tractor forward until the subframe uprights are seated in the boot. 8. Secure the subframe uprights with the bolts and washers. Torque 500 ft-lb. When mounting for the first time, the front hook bolts will have to be tightened after positioning the hook directly over the mounting boss (most rearward position) 9. Raise the loader and lock the support stand tubes in the up position.
Operation - 495 & S495 Loader Removing the Loader from Your Tractor 1. Warning When removing the loader, it must be fitted with a bucket or other suitable attachment to give the frame stability after removal. If this is not done, the frame will not remain standing. Warning Always remove the loader on firm, level ground (away from children's play area and high traffic areas). This makes attaching and removing much faster and easier. It also makes the free standing loader more stable.
Operation - 495 & S495 Loader 4. Roll back the bucket slightly and simultaneously extend or retract the lift cylinders to free hooks from spools. Then slowly back up the tractor. 5. Once the subframe is clear of the boot and the hook is clear of the mounting boss, roll back the bucket all the way. This raises the rear uprights of the loader. On some mountings, the lift cylinders must be extended more while the tractor is backing up, so that the subframes clear the front axle. 6.
General Instructions - 495 & S495 Loader General Instructions As with any piece of equipment, the care with which your loader is operated and maintained will greatly affect it’s life and the safety of the people using it. 1. Keep all pivots well lubricated for longer bushing life. Inspect every 500 hours of operationfor wear. 2. Periodically check all bolts for tightness. If any bolt is damaged, replace it with a bolt ofequivalent grade or strength. 3.
Operation - 495 & S495 Loader TSL General Note and Instructions 1. The true self leveling system (TSL) utilizes mechanical linkages to maintain bucket level while raising and lowering. The pivot plate weldment, leveling tubes and linkages have been developed to ensure that the bucket remains at the same position throughout its range of motion. This feature is standard with 2.50" and 3.00" diameter bucket cylinders. 2.
Troubleshooting - 495 & S495 Loader Troubleshooting Problem Loader slow and/or will not dump Loader chatters or vibrates when raising and lowering Excessive movement at pivots Possible Cause Quick couplers leaking Hydraulic oil too heavy Change or replace filter Oil filter plugged Clean or replace filter Hydraulic pump worn Repair or replace pump Oil line restricted or leaking Replace damaged or restricted hoses or tube lines Inspect, clean, repair or replace valve Air in hydraulic system Cycle
Troubleshooting - 495 & S495 Loader Problem Insufficient lift capacity Possible Cause Remedy Improper hydraulic pump operation Repair or replace pump Load is greater than boom lift capacity Check loader specifications Internal boom cylinder leakage Replace any worn parts and install a seal repair kit Improper hydraulic valve operation Repair or replace valve Worn control valve Worn cylinder piston seals Have authorized dealer replace seals Excessive wear on bottom of bucket and wear pads Flo
Maintenance - 495 & S495 Loader Maintenance Lubrication Lubricate tractor hydraulic unit as indicated in tractor operator's manual. Keep bushings on lift arm pivots and cylinders well lubricated. Use high-grade lithium grease every 8 hours of operation.
Bolt Torque - 495 & S495 Loader Bolt Torque Checking Bolt Torque The tables shown below give correct torque values for various bolts and hex bolts. Tighten all bolts to the torques specified in chart unless otherwise noted. Check tightness of bolts periodically, using bolt torque chart as a guide. Replace hardware with the same strength bolt. Standard Bolt Torque Bolt Size (in) Grade 2 Grade 5 Grade 8 Torque Torque Torque ft-lb NM ft-lb NM ft-lb NM 0.25 0.313 0.
Parts - 495 & S495 Loader Sub Frame Assembly 26
Parts - 495 & S495 Loader Item Part # Description Qty 495 Qty S495 1 31607 495 Sub Frame Weldment Left 1 2 31606 495 Sub Frame Weldment Right 1 1 31611 495 S Sub Frame Weldment Left 1 2 31610 495 S Sub Frame Weldment Right 1 3 113253 Hook Weldment 2 2 4 112747 Plate Clamp 2 2 5 112746 Spacer Block 4 4 6 112748 Shim 2 2 7 112663 Cross Member Weldment 1 1 8 112668 Tube Cross Member 1 1 9 112642 Shaft Pivot 1.75 Dia x 5.
Parts - 495 & S495 Loader Main Frame Assembly 28
Parts - 495 & S495 Loader Item 1 Part # Description Qty 495 Qty 495S 31605 495 Main Frame Weldment 1 - 31609 S495 Main Frame Weldment - 1 2 24296 Quick Attach Weldment Left 1 1 3 24297 Quick Attach Weldment Right 1 1 4 112798 Tube Cross Qtach 1 1 5 108827 Pin Weldment 2 2 6 113433 Stand Weldment 2 2 7 113114 Strap Stand 2 2 8 24329 Wrench Mounting 1 1 9 110907 Pin 0.
Parts - 495 & S495 Loader Hydraulic Plumbing Assembly 30
Parts - 495 & S495 Loader Item Part # Description Qty 1 24458 2.5 Dia. x 20.63 Cyl. Assy. Bucket 2 2 24476 2.5 Dia. x 20.63 Cyl. Assy. Lift 2 3 812973 3/8 x 12" Hose 3/4 Morb x 3/4 Swfjic 2 4 811572 3/8 x 15" Hose 3/4 Morb x 3/4 Swfjic 2 5 812703 3/8 x 22" Hose 3/4 Morb x 3/4 Swfjic 2 6 812697 3/8 x 24" Hose 3/4 Morb x 3/4 Swfjic 2 7 113346 Tubing - Lift Cyl. Bottom Raise 1 8 113347 Tubing - Lift Cyl. Top Drop 1 9 113031 Tubing - Lift Cyl. Common (23.
Assembly - 495 & S495 Loader Assembly Hydraulic Cylinder Assembly Item Bucket Cylinders Diameter 2.50" 3.00" 2.50" 3.00" Length of Stroke 20.63" 20.63" 20.63" 20.63" Retracted Length 33.00" 33.00" 38.00" 38.00" Extended Length 53.63" 53.63" 53.63" 53.63" 24458 24407 24476 24479 Seal Kit No. X1110 X9946 X1110 X9947 Shaft Diameter 1.50" 1.50" 1.50" 1.75" Head Plate No. 24455 24856 24455 23791 2 Shaft Weldment No.
Safety - 495 & S495 Loader Pre-delivery Check List Before delivering this equipment please complete the following check list. __ 1. The loader has been installed using the appropriate mounting kit for the tractor and loader. __ 2. The hydraulic system installed is appropriate for the tractor and loader. __ 3. The loader is properly installed. __ 4. All bolts are tightened to the torque specifications shown in the torque chart. __ 5. All safety decals are readable. __ 6.
Warranty - 495 & S495 Loader Allied by Farm King Limited Warranty This document limits your warranty rights. Base Limited Warranty Buhler Industries Inc. provides this warranty only to original retail purchasers of its product. Buhler Industries Inc. warrants to such purchasers that all Buhler Industries Inc.
Warranty - 495 & S495 Loader Authorized Dealer and Labor Costs Repairs eligible for labor under this limited warranty must be made by Buhler Industries Inc. or an authorized Allied by Farm King dealer. Buhler Industries Inc. retains the exclusive discretion to determine whether it will pay labor costs for warranty repairs or replacements, and the amount of such costs that it will pay and the time in which the repairs will be made. If Buhler Industries Inc.
Warranty - 495 & S495 Loader (Note that some provinces or states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusion may not apply to you.) This warranty gives you specific legal rights and you may also have other rights, which vary from province to province or state to state. Buhler Industries Inc.
www.farm-king.com 1330 43rd Street NW Fargo, North Dakota USA 58102 Ph.: 701.282.7014 | Fax: 701.282.5865 E-mail: info@buhler.com www.farm-king.com Equipment shown is subject to change without notice. ©2011 Buhler Trading Inc. Printed in USA. TSX:BUI a division of Buhler Industries Inc.
