Assembly

ManualsBrandsAllModern ManualsBedsCarey Upholstered Low Profile Standard Bed

upholstered side rails hardware

(6) 1¼” washers(6) 1” x 5/16” bolts

You will need:

• phillips screwdriver

• at head screwdriver

• pliers

*Open all hardware

packets in both packages

before starting assembly.

Wingbacks come with two

additonal bolts/washers

which are listed in the

chart in Step 5.

standard Bed assembly

(4) corner brackets

for all sizes

(2) side rails

for all sizes

support rails

(1) Twin/ Full/ Queen

(3) King/California King

(2) end rails

for all sizes

support legs

(1) Twin

(2) Full

(3) Queen

(6) King/California King

(4) legs

for all sizes

(1) upholstered foot rail

for all sizes

(2) upholstered side rails

for all sizes

bed components

Summary of content (6 pages)

PAGE 1
sta nd ar d Bed as s emb l y upholstered side rails hardware You will need: (6) 1” x 5/16” bolts (6) 1¼” washers • phillips screwdriver • flat head screwdriver • pliers *Open all hardware packets in both packages before starting assembly. Wingbacks come with two additonal bolts/washers which are listed in the chart in Step 5.
PAGE 2
bed hardware 1” x ¼” bolts (1) Twin (2) Full (3) Queen (6) King/California King (4) ¾” x 5/16” bolts (4) ¾” washer for all sizes ¼” nuts (10) Twin/ Full/ Queen (14) King/California King (8) ¾” screws (larger center) (1) wrench (1) 5/32” L wrench (1) 3/16” L wrench for all sizes for all sizes for all sizes ¼” bolts (10) Twin/ Full/ Queen (14) King/California King ¾” washer (smaller center) (1) Twin (2) Full (3) Queen (6) King/California King for all sizes (2) L Brackets for all sizes for al
PAGE 3
Step 1 1. Attach side rail and end rail to corner bracket. Make sure to align holes and snap into thinner slot. Continue this action until you have a rectangular frame. 1 2. Attach corners to rails using (8) ¼” bolts and (8) ¼” nuts. 2 3. Attach legs to rails using (4) ¾” x 5/16” bolts and (4) ¾” washers.
PAGE 4
Step 2 1. Attach each support bar using (2) ¼” bolts and (2) ¼” nuts. Make sure to attach the support bar underneath the bed frame. 1 Note: Twin/ Full/ Queen = 1 support bar King/California King = 3 support bars 2. Attach each support leg to the bar using (1) 1” x ¼” bolts and (1) ¾” washer. 2 (Queen bed frame image displayed) Step 3 1. Use (6) 1” x 5/16” bolts, (6) 1 ¼” washers to attach rails to bed frame loosely. Screw in side rails before attaching the foot rail. 2.
PAGE 5
Step 4 Connect assembled bed frame and rails to your headboard. Attach pieces using (4) 1” x ¼” bolts, (8) 1¼” washers*, and (4) ¼” nuts. Proceed to Step 5 for Wingback beds, otherwise continue onto Step 6. (Queen bed frame image displayed) * Use a washer on each side of the metal legs when attaching headboard to the bed frame. Step 5 Only for Wingback beds: Refer to chart to use assigned bolts and (2) 1 ¼” washers for the top hole (see image). Bolts are enclosed with headboard hardware.
PAGE 6
Step 6 With a phillips screwdriver, attach (2) L brackets and (8) ¾” self-tapping screws in the corners of the foot rail. This is needed to increase stability of upholstered rails.