ALL0237R Wireless N 300Mbit Access Point/Repeater User´s Manual
ALLNET ALL0237R User Manual Table of Contents About the Device ........................................................................................................ 3 Minimum System Requirements.................................................................. 5 Package Contents ....................................................................................... 5 Device Overview ......................................................................................... 5 Front Panel ..................
User Manual Contents About the Device ........................................................................................................ 4 Minimum System Requirements.................................................................. 5 Package Contents ....................................................................................... 5 Device Overview ......................................................................................... 5 Front Panel ...........................................
ALLNET ALL0237R User Manual About the Device ALLNET ALL0237R is a Wall-plugged 300Mbps Wireless-N Repeater, which supports wireless 8 0 2 . 1 1 b /g/n, and one 10/100 Base-T Ethernet port. Repeat and Extend the WiFi Network ALL0237R supports robust 802.11n technology with up to 300Mbps data transfer rate. The extender can take an existing 802.11n wireless signal, repeat and extend it to a longer range where it is too far away for the router or access point to reach.
User Manual Minimum System Requirements Your computer must meet the following minimum requirements. Any operating system can be used Web Browser 233MHz processor Ethernet network adapter Or Wireless network adapter Package Contents Package contents are listed below. For any missing items, please contact your dealer immediately. Product contents may vary for different models.
ALLNET ALL0237R User Manual LABEL STATE DESCRIPTION 3 BARS Connected 95% and above RSSI (Excellent) 2 BARS Connected 55-94% RSSI (Recommended) 1 BAR Connected 10-54% RSSI (Weak) LED RRSI Top Panel WPS Button LABEL WPS BUTTON Page 6 of 27 DESCRIPTION Connect ALL0237R to any WPS capable devices
User Manual Bottom Panel Ethernet Port LABEL Reset Button DESCRIPTION RESET Press the Reset button for 5 seconds to restore the device to default factory settings ETHERNET PORT Connect to computers/Ethernet devices Page 7 of 27
ALLNET ALL0237R User Manual Accessing the User Interface To access the User Interface open a Web browser (Ex: Internet Explorer, Firefox or G.chrome) and type http://192.168.1.1 in the address bar and press enter. Quick Connect Press Quick Connect icon to scan for available wireless within the area.
User Manual Setup Mode of Operation Repeater Configure your device as a wireless repeater to extend the wireless coverage of your wireless router.
ALLNET ALL0237R User Manual SSID Here you can set the name of your wireless network. Select the option Disable on Broadcast SSID allow you to hide the wireless network name. Security Mode Select from different encryption type on the list to be used to provide security to your wireless network from unauthorized users.
User Manual Wireless Wireless Basic Settings Enable Wireless Enable or Disable wireless capability Broadcast SSID Set option to disable to hide your wireless network (Enable by default) SSID Here you can enter the name of your wifi network Wireless Mode This option allows you to select the type of wireless standard you want to allow to connect to your wireless network. Channel Change your wireless channel when you are getting poor reception.
ALLNET ALL0237R User Manual HT Data Rate and HT Guard Interval These options are recommended to be set to Auto for maximum efficiency. Wireless Security Settings Security Mode Select the type of encryption you want for your wireless network WPS Set this option to enable or disable WPS (Wifi Protected Setup) feature on this device Enrollee PIN Enter this PIN to wireless client that will be connecting to ALL0237R repeater to automatically configure the wireless device.
User Manual MAC Filter Settings This feature will provide additional protection to your wireless network. It allows or denies wireless clients from accessing through the ALL0237R with the use of the MAC address which is unique for every network devices. Policy Disable Use this option to disable or disregard the list of MAC address from blocking or allowing access to the wireless network.
ALLNET ALL0237R User Manual Where can I find the MAC address of my wireless client? On the Command Prompt type ipconfig/all to show all the network adapter(s) that are available.
User Manual Firmware Version Shows the current firmware version of the device Build Date Shows the date when firmware is created Serial Number Shows the device’s serial no ETH/Bridge and Wireless MAC address Shows the MAC address of the different Interface Wireless Status Shows the wireless device’s wireless status LAN Configuration Device IP address Shows the device’s current IP address Note: Change this IP address if you are using two ALL0237R on the same network to avoid IP address conflict within you
ALLNET ALL0237R User Manual Configuration Settings Backup Settings Allow you to save the current configuration of ALL0237R. Default file name for the backup file will be “RT2880_Settings.dat”. Click Apply to start saving your configuration. Update Here you can load the saved configuration of your ALL0237R. Click browse and load the saved settings by clicking on the apply button.
User Manual Restore Click on the apply button to reset the unit back to its factory settings. Unsaved information will be lost. Firmware Upgrade This option allows you to update the firmware of your device for future changes and enhancement. Download firmware only at http://www.allnet.de/downloads.html for future enhancement. Updating the firmware a. Connect an Ethernet cable between ALL0237R and computer b. Open web browser and type http://192.168.1.1 to access the user interface c.
ALLNET ALL0237R User Manual d. Click on the Browse button and locate and open the firmware for ALL0237R and click Apply to start the update. Note: It is recommended to only use firmware which is officially release by ALLNET, Using third party firmware will void the warranty of the device. System Password Set a password on web user interface to prevent other users from getting access to the web UI and avoid unwanted changes from your settings.
User Manual Configuring the Device Placement of the Wireless Repeater is crucial to get the best possible results for extending your existing wireless signal. It is ideal for the wireless repeater to be placed in a location where it can receive good wireless signal from the wireless router/AP so as to avoid disconnection and packet loss. LED smart indicator determines the signal strength from your wireless router.
ALLNET ALL0237R User Manual Wireless Repeater a. Plug your ALL0237R to a power outlet, switch it ON and connect the Ethernet cable between your ALL and Computer b. Launch web browser and you will be directed to the User Interface (In case it does not open type 192.168.1.1 and hit enter) c. Select your SSID (wireless network/wifi name) from the list and click connect d. Type the password for the wireless network of your router and click apply.
User Manual SETUP DIAGRAM (REPEATER) Wireless Devices Page 21 of 27
ALLNET ALL0237R User Manual Wireless Access Point Setup your ALL0237R as an access point to provide wireless network to router that doesn’t have wireless feature. a. b. c. Plug your ALL0237R to a power outlet Connect an Ethernet cable between the ALL0237R and Computer Launch web browser and you will be directed to the User Interface d. Go to Setup, set Mode of Operation to Access Point e. Type the name of your wireless network under SSID f. Type the password of the wireless network and click apply g.
User Manual Wireless Bridge Connect wired devices to your wireless network by connecting an Ethernet cable from a wired device, such as a Desktop PC, Game Console or Internet-ready LCD TV, to the Ethernet port of the ALL0237R. a. Plug in and turn ON your ALL0237R b. Connect the Ethernet cable between your computer and ALL0237R c. Launch a web browser. You will be directed to the user interface d. Click on Setup and set Mode of Operation to Bridge e. Type the name of your wireless network for the SSID f.
ALLNET ALL0237R User Manual SETUP DIAGRAM (BRIDGE) WPS WPS or Wifi Protected Setup makes it easier for you to connect your ALL0237R to your wireless router and ALL0237R to your wireless devices with a push of a button. (WPS feature must be enabled and must be supported on the wireless router and wireless devices that will be connected to ALL0237R) Configure ALL0237R to Wireless Router via WPS a. Press the WPS button of ALL0237R for 5 seconds b.
User Manual Page 25 of 27
ALLNET ALL0237R User Manual Safety Precautions Pluggable equipment must be installed near to an easily accessible socket outlet. Do not open, service, or change any component. Only qualified technical specialists are allowed to service the equipment. Observe safety precautions to avoid electric shock. Check voltage before connecting to the power supply. Connecting to the wrong voltage will damage the equipment.
User Manual CE-Declaration of Conformity For the following equipment: Germering, 7th of December, 2012 ALLNET Wireless N 300Mbit Access Point/Repeater ALL0237R The safety advice in the documentation accompanying the products shall be obeyed. The conformity to the above directive is indicated by the CE sign on the device. This equipment meets the following conformance standards: EN300328 V1.7.1 (2006-10) EN301489-1 V1.9.2 (2011-09) EN301489-17 V2.1.1 (2009-05) EN62311.
