ALL0238RD Wireless N 300Mbit Dual-Band Access Point/Repeater User Manual
© Copyright 2014 All rights reserved. No part of this document may be reproduced, republished, or retransmitted in any form or by any means whatsoever, whether electronically or mechanically, including, but not limited to, by way of photocopying, recording, information recording, or through retrieval systems without the express written permission. We reserve the right to revise this document at any time without the obligation to notify any person and/or entity.
User Manual FactoryDefault-IP: 192.168.1.1 Username: admin Password: admin Contents About the Device ........................................................................................................ 2 Minimum System Requirements.................................................................. 3 Package Contents ....................................................................................... 3 Device Design .....................................................................................
User Manual About the Device ALLNET ALL0238RD is a dual band Wall-plugged 300Mbps Wireless-N Repeater, which supports wireless 802.11b/g/n, and one 10/100 Base-T Ethernet port. Repeat and Extend the WiFi Network ALL0238RD supports robust 802.11n technology with up to 300Mbps data transfer rate. The Repeater can take an existing 802.11n wireless signal, repeat and extend it to a longer range where it is too far away for the router or access point to reach.
User Manual Minimum System Requirements Your computer must meet the following minimum requirements. Any operating system can be used Web Browser 233MHz processor (or higher) Ethernet network adapter Or Wireless network adapter Package Contents Package contents are listed below. For any missing items, please contact your dealer immediately. Product contents vary for different models.
User Manual Device Design Front Panel LABEL STATE SMART LED Indicator 3 BARS Connected 2 BARS 1 BAR Connected Connected LABEL STATE OFF 2.4GHz Blinking OFF 5.0GHz Blinking Power LED Page 4 ON DESCRIPTION 95% and above (Excellent) 55-94% (Recommended) 10-54% (Weak) DESCRIPTION No Wireless Device is connected. A Wireless Device is connected and is actively transmitting / receiving data No Wireless Device is connected.
User Manual Top Panel LABEL WPS Button DESCRIPTION Press this button for 2 seconds to connect theALL0238RD to any WPS capable devices (Wireless Device) Press this button for 5 seconds to connect the ALL0238RD to any WPS capable devices (Wireless Router) Bottom Panel Reset Button Ethernet Port LABEL RESET ETHERNET PORT DESCRIPTION Press the Reset button for 30 seconds to restore the device to default factory settings Connect to computers/Ethernet devices Page 5
User Manual SMART LED Indicator Your ALL0238RD is equipped with a SMART LED indicator which determines the signal strength from your wireless router as seen below: NOTE: Wireless reception and throughput may vary according to the number of Wireless Devices that are in use, and at the same time, other nearby wireless devices, structure types, building materials, and other interferences present.
User Manual The Web User Interface The Web User Interface of your ALL0238RD allows you to configure the various features of your ALL0238RD. This will serve as your main tool in monitoring and configuring all of your ALL0238RD’s main features. Accessing the Web User Interface NOTE: To avoid any conflicts in accessing the Web User Interface, it is strongly advised to do the following: • Simply access the Web User interface through an Ethernet connection.
User Manual If you wish to connect to a wireless network immediately you may do the following steps: 1. Click the connect button that corresponds to the network you want to connect to. 2. Enter the correct Wireless Password of the preferred network then click the Apply button.
User Manual 3. Kindly wait for the repeater to finish initializing its connection. Your ALL0238RD would reboot upon successful connection displaying the status depending on the frequency band (2.4GHz or 5.0GHz) of the wireless network you connected to: For 2.4GHz wireless networks For 5.0GHz wireless networks NOTE: To know if you have successfully connected to your device, you may also check the LEDs of your ALL0238RD; the SMART LED Indicator would be in STABLE GREEN light.
User Manual Web User Interface Menu The web user interface was made for users to easily access and control your ALL0238RD’s main features. It is mainly comprised of the following menus: • Quick Connect • Setup • Wireless • Device Admin • Device Status • WPS Quick Connect The Quick Connect menu allows you to scan for the available wireless networks within range and connect to your preferred wireless network as well. To connect to a Wireless Network, simply do the following: 1.
User Manual 2. Determine your preferred wireless network then click its corresponding Connect button. You will then be redirected to the Wireless Setup page of your ALL0238RD as seen below: 3. Input the Wireless network’s passphrase on the WPA Passphrase (Wireless Password) text box then click Apply. Kindly wait for the repeater to finish initializing the connection. Your repeater would reboot upon successful connection.
User Manual Setup The Setup page shows the current properties of the ALL0238RD. This page also allows you to change the mode of operation, the SSID, the security mode, enable or disable the broadcast of your SSID, change the passphrase of the SSID broadcasted by your ALL0238RD, and define the encryption type. • SSID. Refers to your ALL0238RD’s wireless network name. • MAC Address. The MAC address of your ALL0238RD. The information in this field cannot be changed. • Broadcast SSID.
User Manual Wireless The Wireless page shows the current properties of the Wireless Network broadcasted by your ALL0238RD. This menu allows you to modify basic router settings, your wireless network’s security settings, and also add and delete MAC filters.
User Manual Basic Wireless Settings The Basic Wireless Settings page allows you to configure the basic properties of your ALL0238RD such as enabling the wireless feature and SSID broadcast, changing the name of the Wireless SSID, defining a preferred wireless mode for your ALL0238RD, changing the Wireless channel and various HT properties • Enable Wireless. Enable or Disable the wireless feature of your ALL0238RD. By default the Wireless feature of your ALL0238RD is enabled. • Broadcast SSID.
User Manual • Channel. You may opt to change your wireless channel when you are getting poor reception. You may choose the least channel used in your area for better wireless performance. • Channel Bandwidth. Here you can set your Channel Bandwidth to 20MHz and 20/40MHz. It is strongly suggested to leave this in Auto to achieve the best efficiency. • HT Data Rate and HT Guard Interval. These options are recommended to be set to Auto for maximum efficiency.
User Manual Wireless Security Settings The Wireless Security Settings page allows you to change the Security Mode, enable or disable the WPS feature of your ALL0238RD, and add a WPS enabled device by entering the needed PIN. • Security Mode. Select the type of encryption you want for your wireless network. • WPS. Allows you to enable or disable the WPS feature of your ALL0238RD. • Enrollee PIN.
User Manual MAC Filter Settings The MAC Filter page will provide additional protection to your wireless network. It allows or denies Wireless Devices from accessing the ALL0238RD with the use of the MAC address which is unique for every network device. To add a MAC Filter: 1. Specify your preferred Policy. • Disable. Disables the application of a MAC Filter to a specific device or to all the MAC Addresses specified in the list. • Allow.
User Manual d. Locate the Ethernet Adapter Ethernet or Ethernet Adapter Local Area Network section and find the ‘Physical Address’ (MAC Address). 3. Click the button located beside the MAC Address text box to apply changes. To remove a MAC Filter: 1. Click the button that corresponds to the MAC address that you wish to remove from the list.
User Manual Device Admin The Device Admin page allows you to configure various system oriented settings such as changing the devices IP Address, backing up the current configuration settings, upgrading the device’s firmware, restoring the device from a previously saved configuration file, resetting the device to its factory default, and defining a user password for the Web UI.
User Manual Device Information Allows you to view basic device information regarding your ALL0238RD such as the firmware version and its build date, the device’s serial number, MAC addresses of various interfaces, and view the Wireless’ status as well. • Firmware Version. Shows the current firmware version of the device • Build Date. Shows the date the firmware was created. • Serial Number. Shows the device’s serial number. • ETH/Bridge and Wireless MAC address.
User Manual LAN Configuration The LAN Configuration page allows you to specify a device IP address and Device subnet mask your ALL0238RD will use. Note: Change this IP address if you are using two ALL0238RD on the same network to avoid the occurrence of IP address conflict within your network. Configuration Settings The configuration settings page allows you to backup your ALL0238RD’s current settings, do a firmware upgrade, and restore an existing configuration by using the backed up file. • Backup.
User Manual • Update. Here you can load the saved configuration of your ALL0238RD. Click browse and load the saved settings then click the Apply button. • Restore. Click on the apply button to reset the unit back to its default factory settings.
User Manual Firmware Upgrade The Firmware Upgrade page allows you to update the firmware of your device for future changes and enhancement, however, it is strongly suggested to only upgrade your device firmware if it was advised by ALLNET GmbH Computersysteme. You may download the latest firmware for your device at www.allnet.de/downloads.html . To upgrade the firmware: 1. From the System page, click the Firmware Upgrade button. 2.
User Manual System Password Set a password on the web user interface to prevent other users from getting access to the web UI and avoid unwanted changes from your settings. To add a system password, simply type in your preferred password and click on apply to activate this feature. To disable the password, simply remove the password and click apply to save your settings. Note: Forgotten passwords cannot be recovered.
User Manual Device Status The device status page shows the current status of the AP, and also the wireless devices that are currently connected wirelessly to your ALL0238RD.
User Manual WPS WPS or Wifi Protected Setup makes it easier for you to connect your ALL0238RD to your wireless router and the ALL0238RD to your wireless devices with a simple push of a button. To connect the ALL0238RD to a Wireless Router via WPS: 1. Press the WPS button of ALL0238RD for 5 seconds. 2. Press the WPS button on your router for 2 seconds. To connect the ALL0238RD to a Wireless Device via WPS: 1. Press the WPS button of ALL0238RD for 2 seconds. 2.
User Manual Setup the Device In setting up your device kindly follow the instructions provided below. A diagram has also been provided for additional reference. 1 2 1. Plug your ALL0238RD to a power outlet. 2. Connect your ALL0238RD to the computer using an Ethernet cable through their respective Ethernet ports. 3. Launch a web browser and you will automatically be redirected to the Web User Interface of your ALL0238RD. If in any case it does not open, kindly type 192.168.1.
User Manual For 2.4GHz wireless networks For 5.0GHz wireless networks 6. Disconnect the Ethernet cable from ALL0238RD and computer then place the device at the location where it can get sufficient reception from your wireless router.
User Manual Page 29
User Manual Appendix FCC Statement This equipment has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications.
User Manual Safety Warnings For your safety, be sure to read and follow all warning notices and instructions. Do not open the device. Opening or removing the device cover can expose you to dangerous high voltage points or other risks. Only qualified service personnel can service the device. Please contact your vendor for further information. Do not use your device during a thunderstorm. There may be a risk of electric shock brought about by lightning. Do not expose your device to dust or corrosive liquids.
User Manual CE-Declaration of Conformity For the following equipment: Germering, 20th of March, 2014 WLAN N Access Point/ Repeater Dual-Band ALL0238RD The safety advice in the documentation accompanying the products shall be obeyed. The conformity to the above directive is indicated by the CE sign on the device. The ALLNET ALL0238RD conforms to the Council Directives of 1999/5/EC. This equipment meets the following conformance standards: This equipment is intended to be operated in all countries.
User Manual ALLNET GPL Code Statement This ALLNET product includes software code developed by third parties, including software code subject to the GNU General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). As applicable, the terms of the GPL and LGPL, and information on obtaining access to the GPL code and LGPL code used in this product, are available to you at: http://www.allnet.de/gpl.
User Manual To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code.
User Manual no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole.
User Manual distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.
User Manual LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12.
User Manual The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than `show w' and `show c'; they could even be mouse-clicks or menu items--whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the program, if necessary. Here is a sample; alter the names: Yoyodyne, Inc.
