Instructions / Assembly

ManualsBrandsAllSpace ManualsShelving24 in. W x 12 in. D Short Wire Shelf

THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,

MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL

CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS

PERSONAL INJURY AND/OR PROPERTY DAMAGE. IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A

PROBLEM WITH YOUR PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER

SERVICE DEPARTMENT AT 1-800-423-3598. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE:

MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR

PROBLEM OVER THE PHONE. .

Wall Organization System

Assembly Instructions

Welcome to Allspace! You have just purchased one of the most flexible multi-configuration

systems in the world of organization. Before you start assembly, please note the many

configuration suggestions at the end of the manual.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

Summary of content (13 pages)

PAGE 1
Welcome to Allspace! You have just purchased one of the most flexible multi-configuration systems in the world of organization. Before you start assembly, please note the many configuration suggestions at the end of the manual. Wall Organization System Assembly Instructions THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS.
PAGE 2
SAFETY WARNINGS WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. READ ALL INSTRUCTIONS BEFORE ASSEMBLY. Follow all warnings and safety precautions. If the installation is not performed correctly, the unit could fall off the wall and cause serious injury or death. Always use appropriate safety equipment when using power and hand tools. Always wear eye protection.
PAGE 3
COMPONENTS Component 450048U 450048C 450048HF 450075HF 450076HF 3 3 2 Component 1 2 2 1 2 450036-02 26 in. Top Track 10 10 3 6 3 3 2 2 1 1 1 N/A ✽✽ 1 1 1 N/A ✽✽ 8 8 4 6 15 15 9 9 22 22 16 12 6 6 4 4 5 5 3 3 6 6 4 N/A ✽✽ 37 37 25 21 450075HF 450076HF 450036-21 Standard Bar Connector 6 6 4 4 450036-23 Bike/Ladder Hook 4 4 2 3 450036-24 Hose Hook 450036-04 15 in. x 23-1/2 in.
PAGE 4
INSTALLATION The Allspace Wall Organization System was created to give you the amount of organization you need in whatever size space you have. Change that bare wall in the garage into rows of easily found tools. Store household items in that space above the washer. Keep office supplies handy by hanging a single square of pegboard in your home office. Allspace can fit in almost any space to serve almost any need.
PAGE 5
MOUNTING THE TOP TRACKS Now you are ready to mount the top tracks (450036-02). Remember that the insert slots in the tracks must be facing up toward the ceiling. Do not mount the track upside-down. For non-stud-direct wallboard mount, use minimum of three wall anchors (45003630/450036-36) per 26 inch top track. Your wallboard must be 5/8 in. or thicker for wallboard mount. When installing into wallboard, slip the plastic wall anchor sheath (450036-36) onto the 1.5 in. wall screws (450036-30).
PAGE 6
Each track must have at least two stud screws or three wallboard screws securing it to the wall. Use a level to check each track as it is mounted. Step 4 FASTENING VERTICAL STANDARDS TOGETHER 450036-03 450036-21 450036-32 Step 5 Now it is time to attach the vertical standards. These are the tracks that will run on either side of each piece of pegboard.
PAGE 7
MOUNTING VERTICAL STANDARDS TO TOP TRACKS 450036-02 450036-03 Step 6 Find the insert slots located on the top of the tracks (450036-02). Make sure the notch on the end of the standard (450036-03) is facing up. Line up the arms of the standard with the insert slots and careful push in and down. The standard should drop into the opening in the track with the notch hanging on the track lip. If needed, the standards have screw or wallboard mount holes for extra fastening support.
PAGE 8
MOUNTING PEGBOARD PANELS Make sure that the keyholes in both bars are facing the same direction. The round part of the keyhole should be toward the top. Step 8 450036-04 If you want the panels to fit tightly together in double vertical panel configurations (one panel on top of the other), you must insert the bottom pegboard panels first. Otherwise, mount pegboard panels as needed. Each pegboard panel (450036-04) has mounting hooks along either side.
PAGE 9
MOUNTING THE UTILITY TRACK This set includes four utility track bars. These utility track (450036-01) can be used for hanging bikes, ladders, hoses and larger tools. You can mount these tracks wherever they are needed. They can be mounted between the upper and lower pegboards or they can be mounted at the bottom below the pegboards. They can even be mounted on the pegboards themselves or directly to the wall without using vertical standards.
PAGE 10
MOUNTING HOOKS, UTILITY TRAYS AND BASKETS Now you are ready to attach the various hanging accessories. The plastic hooks have a keyhole-shaped lock on the back. To hang them, simply line the lock up with one of the keyholes in the pegboard and insert. Gently pull the hook down to lock into place. To remove, just reverse the procedure. Step 11 To hang a utility tray (450036-16/450036-17), line up both hooks with the keyholes on the pegboard. Insert into keyholes and pull down to lock. (See Figure 1.
PAGE 11
PREPARING AND MOUNTING BIKE/LADDER/HOSE HOOK Before you use the bike/ladder hook (450036-23), it is necessary to release the bike hook from its packing position. To do this, turn bike hook around so you can see the springs inside. Push up on one of the arms until you are able to swing it to the side. Release and the spring will pop back into the locked position. Repeat for the other side. (See Figure 3.) Depress springs and swing out to release bike hook arms.
PAGE 12
PREPARING AND MOUNTING WIRE SHELF AND BRACKET Note: Instructions only apply for model no. 450076HF 450036-38 Figure 1 Figure 2 Figure 3 Insert top hook of shelf bracket (450036-38) into mounting slot of vertical standard (450036-03) at desired height. The bracket should be inserted at an oblique angle (See Figure 1) Rotate shelf bracket clockwise until bottom hooks slide into mounting slot of vertical standard (See Figure 2).
PAGE 13
VERSATILITY Remember that your pegboard system can be adjusted to fit any space you have. Use one panel or all four, it’s up to you. 100 in. 37-7/8 in. 37-7/8 in. 52 in. 49 in. 52 in. 18-15/16 in. 25 in. 74 in. 37-7/8 in. 49 in. 18-15/16 in. 76 in. 25 in. 25 in. 100 in. 25 in. 25 in. 37-7/8 in. 18-15/16 in. 26 in. 18-15/16 in. 100 in. 25 in. 49 in. China Patents No. ZL 2014 2 0623701.