Owner's manual

ManualsBrandsAllstar Products Group ManualsKitchenSUPER BELT MVP-SB

1

2

3

4

5

6

7

8

9

INSTALLATION AND OWNER’S MANUAL

As of date of manufacture,

meets all ANSI/UL 325 Safety

Requirements for Vehicular

Garage Door Openers

Residential Vehicular Garage Door Opener

Model MVP-SB SUPER BELT

READ THIS MANUAL CAREFULLY BEFORE INSTALLATION OR USE

104334

INSTALLER: Place this manual in the plastic envelope provided and

permanently attach to the wall near the pushbutton.

Product Features ................................................... 2

Component Identification..................................... 3

Identify Your Door Type ........................................ 3

Important Installation Instructions........................ 4

Assembly Instructions........................................... 5

Installing the Opener ............................................. 7

Mounting the Front Bracket ................................ 7

Mounting the Power Head................................... 7

Power Requirements/Permanent Wiring ............ 8

Control and Auxiliary Equipment.......................... 9

Installation of the Super Station ......................... 9

Standard Wall Push Button Installation ............. 9

Installation of Safe Finish Photosystem........... 10

Important Safety Instructions ........................... 11

Installation Checklist ........................................... 12

TABLE OF CONTENTS

WARNING

Indicates a

MECHANICAL

hazard of INJURY

OR DEATH. Gives

instructions to avoid

the hazard

.

Operation and Adjustment Instructions..............12

Basic Operating Parameters..............................12

Door Arm Connection ........................................13

Programming The Radio System ...................... 14

FCC and IC Radio Operation Statement ..........15

Testing the Limit Settings..................................16

Testing the Sensitivity .......................................16

Testing the Reversing System ..........................16

Testing the Safe Finish Photosystem ...............17

Operating the Super Station..............................17

Wiring Diagram..................................................... 18

Using the Manual Release Mechanism ...............19

Troubleshooting Guide ........................................19

Warranty Statement..............................................20

CAUTION

READ THESE STATEMENTS CAREFULLY AND FOLLOW THE INSTRUCTIONS CLOSELY

The Warning and Caution boxes throughout this manual are there to protect you and your equipment.

Pay close attention to these boxes as you follow the manual.

WARNING CAUTION

Indicates an ELECTRICAL

hazard of DAMAGE to the

door, door opener, or

equipment. Gives

instructions to avoid the

hazard

.

Indicates an

ELECTRICAL hazard

of INJURY OR

DEATH. Gives

instructions to avoid

the hazard

.

Indicates a MECHANICAL

hazard of DAMAGE to the

door, door opener, or

equipment. Gives

instructions to avoid the

hazard

.

By

Summary of content (20 pages)

PAGE 1
By As of date of manufacture, meets all ANSI/UL 325 Safety Requirements for Vehicular Garage Door Openers Residential Vehicular Garage Door Opener Model MVP-SB SUPER BELT INSTALLATION AND OWNER’S MANUAL INSTALLER: Place this manual in the plastic envelope provided and permanently attach to the wall near the pushbutton. 104334 READ THIS MANUAL CAREFULLY BEFORE INSTALLATION OR USE TABLE OF CONTENTS Product Features ................................................... 2 Component Identification ...........
PAGE 2
PRODUCT FEATURES The purpose of this booklet is to provide assembly, installation and operation information concerning the herein described Residential Garage Door Opener and related Accessory Products. NOTICE IT IS IMPORTANT THAT THIS INSTRUCTION MANUAL BE READ AND UNDERSTOOD COMPLETELY BEFORE INSTALLATION OR OPERATION IS ATTEMPTED. NOTICE THE IMPORTANT SAFEGUARDS AND INSTRUCTIONS IN THIS MANUAL CANNOT COVER ALL POSSIBLE CONDITIONS AND SITUATIONS WHICH MAY OCCUR DURING ITS USE.
PAGE 3
COMPONENT IDENTIFICATION RAIL/BELT ASSEMBLY DOOR ARM ROD DOOR ARM TUBE ASSEMBLY OPENER POWER UNIT CONTROL WIRE SPOOL OPENER HARDWARE PACKET BELT GUARD DOOR MOUNTING BRACKET SUPER STATION DELUXE WALL PUSH BUTTON RELEASE ROPE AND KNOB ! RUBBER BUMPER PUSHBUTTON “WARNING” LABEL RADIO TRANSMITTER TROLLEY OUTER HALF WALL MOUNTING BRACKET SAFE FINISH PHOTOSYSTEM WAR N I N G Child can be pinned under automatic garage door. Death or serious injury can result.
PAGE 4
IMPORTANT INSTALLATION INSTRUCTIONS WARNING! TO REDUCE THE RISK OF SEVERE INJURY OR DEATH READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS! AN UNBALANCED DOOR OR ONE THAT STICKS OR BINDS MAY PREVENT THE SENSING SYSTEM FROM WORKING PROPERLY, CAUSING INJURY OR DEATH. ENSURE DOOR IS PROPERLY BALANCED AND ELIMINATE ANY STICKING OR BINDING PRIOR TO INSTALLATION OF OPERATOR.
PAGE 5
ASSEMBLY INSTRUCTIONS NOTE: The Tee Rail/Belt Assembly is packaged separately from the Power Unit. The Inner Trolley half, Front Idler Sprocket, Belt, and Limit Cams are assembled on the Tee Rail at the factory. Follow the steps outlined below to complete assembly prior to installation. Refer to the Component Identification illustrations on page 3.
PAGE 6
ASSEMBLY INSTRUCTIONS STEP 6: VERY IMPORTANT: REINSTALL THE BELT RETAINING BLOCK REMOVED IN STEP 1 AT THIS TIME. SEE ILLUSTRATION E. Failure to reinstall the Belt Retaining Block may cause the operator to not reverse correctly. Tighten the two screws to securely hold the Belt Retaining Block in place. Install the Belt Guard by seating the guard over the the Drive Sprocket and Rear Idler Pulley on the power unit and snapping into place, see Illustration E.
PAGE 7
INSTALLING THE OPERATOR HORIZONTAL LINE VERTICAL CENTERLINE STEP 1: Mounting the Front Bracket — Sectional Doors and One-Piece Doors with Track: Mark a vertical centerline on the header above the door. By manually raising the door, determine the high arc of the door’s travel (see illustrations on page 4 ) and using a level, transfer this measurement to the header (see illustration at left). Draw a horizontal line, crossing the previously drawn centerline, at this point.
PAGE 8
INSTALLING THE OPERATOR about location of, and attachment to, ceiling joists, a carpenter should be contacted to provide assistance. A cross brace will be necessary if the power head is mounted 8” or more from the ceiling, see illustration at bottom of previous page. Attach a kick brace from the hanger angle to an opposite end Power Unit mounting hole to provide horizontal stability as shown. Optionally a hanger angle at the opposite end mounting hole can be used to provide horizontal stability.
PAGE 9
CONTROL AND AUXILIARY EQUIPMENT INSTALLATION OF THE SUPER STATION OR A STANDARD WALL PUSH WARNING BUTTON The Super Station (Deluxe Wall Pushbutton Station) is a 7 function station designed to work with and maximize the operation of your opener. Connection to any other operator may damage the operator and/or the Super Station. Only connet one Super Station to the operator. Do not connect more than one Super Station to the Operator.
PAGE 10
CONTROL AND AUXILIARY EQUIPMENT 10 Step 5: Install a Control Button Warning Label near place a similar mark on the opposite door jamb. The each control station, see illustration on previous page. One label is supplied with your opener. Contact your installing Dealer or the factory for additional warning labels. brackets may be temporarily mounted to the jamb with a 1" flat head nail (provided) using the small hole above the slot.
PAGE 11
STEP 4 : CONTROL AND AUXILIARY EQUIPMENT 108971 Final Installation A. Attach the"U" brackets to the "L" brackets with a 1/4-20 carriage bolt, washer and hex nut (provided). Insert the bolt from the inside of the "U" bracket and hand tighten only at this time. B. Place the transmitter and receiver units into their respective "U" brackets. See Illustration, at right. C. Connect the interconnect wire pair to the garage door opener terminals marked "1" & "4".
PAGE 12
OPERATION AND ADJUSTMENT INSTRUCTIONS 12 5. All wiring is correct to codes or better. There is PRE-POWER ONground continuity from the supply. The ground INSTALLATION CHECKLIST prong on the power cord is intact. Before continuing with the operation and adjustment section, make sure that: 6. All ropes have been removed from the door. The door moves freely without binding when 1. The front and rear mounts for the operator are raised or lowered manually.
PAGE 13
CAUTION! OPERATION AND ADJUSTMENT INSTRUCTIONS FIBERGLASS, ALUMINUM OR LIGHTWEIGHT STEEL GARAGE DOORS WILL REQUIRE REINFORCEMENT BEFORE INSTALLATION OF DOOR MOUNTING BRACKET. CONTACT YOUR DOOR MANUFACTURER FOR A REINFORCEMENT KIT OR INSTRUCTIONS. DOOR ARM CONNECTION AND INSTALLATION 110054-2 NOTE: If the door is of light construction IT IS necessary to reinforce the center stile with steel angle or wood to prevent damage to the door if it encounters an obstruction on closing.
PAGE 14
OPERATION AND ADJUSTMENT INSTRUCTIONS Remote Control Radio System As your transmitter is pre-coded at the factory with three of over 19,000 unique codes. As such, it is possible to control a single operator or a group of operators at one location or at multiple locations. The transmitter may be mounted on a visor using the metal visor clip (included) or attached to a key-chain with the built-in attachment. Your Remote Control Radio System transmitter is compatible with the HomeLink® systems.
PAGE 15
OPERATION AND ADJUSTMENT INSTRUCTIONS TEACHING THE OPERATOR THE TRANSMITTER CODE Press program button on Deluxe Wall Station Deluxe Wall Station Red LED and work light on the operator will turn ON (Note: The MVP radio system will learn 8 different MVP transmitter codes.
PAGE 16
OPERATION AND ADJUSTMENT INSTRUCTIONS STEP 1: Testing the Limit Settings: To check the Limit Settings, start the Opener by pushing the standard wall Push Button or Super Station. Be prepared to activate the button again quickly - per the Operating Parameters outlined on page 12 - or if you see that the door is going to over travel. As illustrated below, move the Cams toward the Power Unit to DECREASE door travel and toward the Front Idler to INCREASE door travel.
PAGE 17
OPERATION AND ADJUSTMENT INSTRUCTIONS adjustments are correct, the door will reverse within two seconds of contacting the object and travel to the Full Open position. If this does not occur, recheck the Limit Adjustments (Step 1, previous) and Sensitivity Adjustments (see Steps 2 & 3, previous). 104392 WARNING 1 1/2” BLOCK OF WOOD LAID FLAT (2”X4”) NOTE: Any time adjustments are made to Limits FAILURE TO TEST REVERSING SYSTEM COULD RESULT IN DEATH OR SERIOUS INJURY.
PAGE 18
OPERATION AND ADJUSTMENT INSTRUCTIONS 104394 STOP Button OPEN Button Learn Enable Button CLOSE Button Light Button Security Disable Switch Security Switch 2. Close Push button — Green-backlighting, arrow pointing down. Used to start the door downward. This button has no effect on a door in motion. Will allow constant pressure close operation if the photocell is misaligned. 3. Stop Button - Red-backlighting, universal “STOP” within an octogon. Used to stop a door in motion.
PAGE 19
WIRING AUXILIARY EQUIPMENT MANUAL RELEASE OPERATION TO RELEASE: WARNING KEEP PEOPLE AND OBJECTS OUT OF DOOR OPENING WHEN USING MANUAL DISCONNECT. AN OPEN OR PARTIALLY OPEN DOOR MAY FALL UNCONTROLLABLY IF DISCONNECTED FROM OPERATOR. CONTACT A SERVICE PROFESSIONAL TO CORRECT ANY DOOR PROBLEMS. TO RE-ENGAGE: NOTE: The MANUAL RELEASE MECHANISM is engaged by pulling the Release Handle down and away from the door.
PAGE 20
Manufacturer’s Limited Warranty Linear LLC warrants its Allstar brand MVP Series residential vehicular garage door operators as follows: • The drive train to be free from defects in materials and workmanship for Model MVP-SB (SuperBelt) for the entire period of ownership by the original purchaser. The drive train includes the motor, drive pulleys, drive shaft and sprocket, T-rail, frame and belt.