Installation Instructions

ManualsBrandsAllura ManualsBuilding materials12" Textured Solid Fibercement Soffit

MaxiSOFFIT

to ASTM E-136, with zero me spread in accordance to ASTM E-184.

MaxiSOFFIT

STORAGE AND HANDLING:

 Protect from the weather.

 Use the plastic cover that is provided with the pallet to keep

product dry.

 MaxiSOFFIT

is produced with a factory-applied

primer; this primer does not provide adequate resistance

to moisture in the event the product is allowed to become

saturated during storage. If MaxiSOFFIT

becomes wet or

saturated, allow product to dry before installation.

 Store product

dry and at prior to installation.

 Installing MaxiSOFFIT

wet or saturated may cause

shrinkage at butt joint, which could produce breakage at corners.

 Protect edges and corners from chipping.

 Carry panels on edge.

MAXITILE is not responsible for damage caused by improper storage and / or handling of the product .

LAP SIDING INSTALLATION GUIDE

MaxiSOFFIT

It will not rot or deteriorate. It is non-combustible in accordance

is available in ¼” (6 mm) nominal thickness in

two types: Vented (V) and Non-Vented (NV), in two textures,

Smooth and Classic Cedar. Vented is designed

for generating natural ventilation, with more than 5 square

inches of vented area per lineal foot.

We suggest that you read these instructions at least twice.

and MAXITILE

Summary of content (6 pages)

PAGE 1
MaxiSOFFIT TM LAP SIDING INSTALLATION GUIDE and MAXITILE We suggest that you read these instructions at least twice. M a x i S O F F I T TM It will not rot or deteriorate. It is non-combustible in accordance to ASTM E-136, with zero me spread in accordance to ASTM E-184. MaxiSOFFIT TM is available in ¼” (6 mm) nominal thickness in two types: Vented (V) and Non-Vented (NV), in two textures, Smooth and Classic Cedar.
PAGE 2
PACKAGING: MaxiSOFFIT TM is delivered in full pallets. Type Thickness Non-Vented Non-Vented Vented or Non-Vented ¼” (6 mm) Width 4’ (1.22 m) 12” (0.30 m) Vented or Non-Vented 16” (0.41 m) Vented or Non-Vented 24” (0.61 m) Length Weight 8’ (2.44 m) 62.5 lb (28.4 kg) 60 pieces/pallet 10’ (3.05 m) 78.1 lb (35.5 kg) 50 pieces/pallet 12’ (3.66 m) 8’ (2.44 m) Packing 23.4 lb (10.6 kg) 240 pieces/pallet 31.3 lb (14.2 kg) 180 pieces/pallet 31.3 lb (14.
PAGE 3
FASTENERS:  Fasteners must be corrosion-resistant; preferably quality hot dipped galvanized nails. MAXITILE is not responsible for corrosion resistance of fasteners. Stainless steel fasteners are recommended when installing MAXITILE products near the ocean, or in very humid climates. Always check local building codes for additional requirements.  Screws shall be self-drilling all weather or stainless steel.  Staples are not allowed.
PAGE 4
INSTALLATION:   MaxiSOFFIT TM panels must be fastened to a solid, nailable substrate such as wood 2x subfascia.  Additional framing may be needed to ensure proper fastening.    An insect screen can be installed using building adhesive, but the net ventilation will be reduced. JOINTING METHODS:  Install MaxiSOFFIT TM panels in moderate contact at ends or leave 1/8” gap and caulk.  Maintain a minimum 1” gap between gutter end caps and siding & trim.
PAGE 5
FINISHING:  Patching:    Repair chips and dents with acrylic patching mortar. Prime patched areas before coating. Apply primer to repaired areas and then paint.  Use high quality, exterior grade, paintable elastomeric joint sealant, complying with ASTM-C 834 or ASTM-C 920 (grade NS, class 25) regulations. Caulking must be applied according to manufacturer’s written instructions and ASTM-C 1193.  Caulking:  Painting: MAXITILE siding, soffi t and trim must be allowed to breathe.
PAGE 6
MAXIMUM WIND LOADS FOR MaxiSOFFITTM Thickness (inch) 1/4” Fastener Type Fastener Spacing Frame Type 4d box 1½ 6 inches on 2 by 4 inch long center wood5 nails4 Stud Spacing (inches) Height of Building (feet) 16” 15 20 40 60 Maximum basic wind speed (mph) for exposure category 1 IBC, IRC2 UBC 3 B C 125 100 120 100 110 85 105 85 D B C D 85 85 --- 105 100 90 85 80 80 70 70 70 70 --- 1 N/A – not applicable 2 Basic wind speed is the 3-second gust, miles per hour (km/hr), in accordance with IB