Installation and Operation E R O F E B D REA CKING! A UNP Complies with ADA LISTED Guidelines
CONTENTS Introduction and Contact Information ................................... 3 Safety Instructions and Warnings ........................................ 4-5 INSTALLATION AND ASSEMBLY Rough-In Dimensions .......................................................... 6 Location and Leveling .......................................................... 7 Assembling the Fittings........................................................ 8-13 Hose Connections .......................................................
INTRODUCTION AND CONTACT INFORMATION Congratulations on your Walk-In Bathtub purchase. We know you’ll enjoy many years of comfort and convenience using it! Great care has gone into the design of our walk-in tubs to simplify the installation process, and to make the operation of your tub easy and troublefree. This manual will explain basic installation techniques and cover the operation of your tub. Please read it completely before you or your installer begins the installation process.
INSTALLATION INSTRUCTIONS UNPACKING AND MOVING YOUR TUB Inspect the shipping carton prior to unpacking. Use caution with box cutters or razor knives. In the unlikely event of damage which causes you to believe the bathtub inside may be damaged, document the damage by taking a photograph of the damaged area, and immediately contact your salesman or the company from which you purchased the tub. When moving the tub prior to installation, carry the bathtub by its metal sub-frame.
IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS IMPORTANTES RELATIVES A LA SECURITE READ AND FOLLOW ALL INSTRUCTIONS LIRE ET SUIVRE TOUTES LES INSTRUCTIONS SAVE THESE INSTRUCTIONS CONSERVER CES INSTRUCTIONS WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; CHILDREN SHOULD NOT USE HYDROMASSAGE BATHTUB WITHOUT ADULT SUPERVISION AVERTISSEMENT: RISQUE DE BLESSURE ET DE NOYADE. NE PAS LAISSER UN ENFANT UTILISER LA CUVE A REMOUS EN L’ABSENCE D’UN ADULTE.
ROUGH-IN DIMENSIONS When installing tub, use galvanized screw or nail driven into wall stud to overlap tub flange as shown below at left. Do NOT insert screw or nail through tub flange as shown below at right. This will weaken the tub’s structure and void the warranty. OK 1 2 3 4 5 1 NO! 2 Nail / screw does NOT pass through tub flange, damages tub. 1. 2. 3. 4. 5. Wall stud Sheetrock Nail or screw Tile Bathtub 3 Nail / screw passes through tub flange, damages tub.
Note: Since no two customers’ installations will be identical, these instructions are intended solely as a general reference. Your installation may vary depending on your circumstances. Installations should be done by a licensed contractor or plumber, and electrician. LOCATION AND LEVELING First, “test fit” the tub by placing it in the position where it will be installed.
ASSEMBLING THE FITTINGS Your tub comes with high quality brass fittings coated with a durable chrome finish. These include a Hand Shower, a Spigot, two Faucet Valves and a Diverter Valve. These fittings and their attachment hardware can be found in the accessories box shipped inside the tub. All threads should be wrapped with Teflon® tape prior to assembly.
FAUCET ASSEMBLY (cont.) To assemble the faucet valves, first install one rubber washer, steel washer, and retaining nut on faucet valve body in order shown (parts 5,6 and 7). Push faucet valve body (3) from bottom through correct hole in tub deck (4) and install second rubber washer, steel washer and retaining nut (5,6,7). Do not overtighten. Screw on chrome retaining ring (2), being careful not to damage the tub’s finish. Attach faucet handle (1).
SPIGOT ASSEMBLY Assembly of the spigot is as follows: Insert spigot body (1) and trim ring (2) from above through hole in tub deck (4). Be sure locating pin (8) is aligned correctly with small hole in tub deck. Install rubber washer (5) , steel washer (6) and retaining nut (7) on spigot valve body (3). Thread the spigot valve body through trim ring and tighten into spigot body. Tighten retaining nut. Do not overtighten. All threads should be wrapped with Teflon® tape prior to assembly. 1 8 2 5 6 7 4 1.
HAND SHOWER ASSEMBLY To assemble the hand shower, insert chrome hand shower support (1) through tub deck (3) from above. Install rubber washer (4) and retaining nut (5) on threaded portion of chrome hand shower support. Insert flexible hand shower hose (not shown for clarity) through chrome hand shower support (1). Connect the hand shower hose to the hand shower (1). Place hand shower (2) into chrome hand shower support.
HOSE CONNECTION Connect hoses* as shown in the diagram below. 1. Cold Water Faucet 2. Spigot/Diverter 1 5 2 4 3 6 3. Hot Water Faucet 4. Hand Shower 8 9 5. Cold Water Supply* 6. Faucet-to-Spigot Line: Cold 7. Hand Shower Hose 7 8. Faucet-to-Spigot Line: Hot 9. Hot Water Supply* *Water supply hoses not included. DRAIN CONNECTION 1 2 To Overflow Although drain connection may vary depending on your circumstances, a typical installation is shown at left.
ASSEMBLING THE FITTINGS: 46-INCH MODELS ONLY The 46” bathtub uses a slightly different faucet configuration. Rather than a diverter within the spigot, the diverter is a separate valve (see below). Installation and assembly is the same as pages 8-10. These fittings and their attachment hardware can be found in the accessories box shipped inside the tub. All threads should be wrapped with Teflon® tape prior to assembly.
ELECTRICAL CONNECTION Your Walk-In Bathtub functions on standard 110V-120V alternating current. The electrical connection of your tub must be installed in accordance with the National Electrical Code and with all local codes. It is highly recommended that your tub be wired on a separate circuit, with a dedicated GFCI circuit breaker rated for 25 amps. If the new circuit run exceeds 100 feet check with local codes for requirements.
ACCESS PANELS Your tub is designed for a trouble-free service. In the unlikely event that service is necessary, there are two access panels in the front of the tub. These are held in place by magnets, and can be removed with the suction cup tool included with your tub. ACCESS PANELS IN PLACE ACCESS PANELS REMOVED EXTENSION PANELS In the event that you wish to install your tub in a space wider than the tub itself, there is an extension panel kit inluded with your tub.
OPERATION (Jetted Bathtubs Only) CONTROL PANEL Once your Walk-In Bathtub is assembled and installed the operation is simple. On the inside wall of the tub you will see a control panel like the one shown at right and below. There are three buttons which control the functions of the tub. On-Off Switch Water Jet Switch Air Jet Switch First, turn on the power to the tub by pressing the On-Off button. The indicator light on the button will illuminate, signifying that the tub has been turned on.
INLINE HEATER FUNCTION The Inline Heater is pre-programmed to maintain a water temperature of 104o F. It is not designed to raise the temperature of cold bathwater, but to maintain the water temperature while running the water jet system. It is activated automatically when the water jet system is turned on, senses the current water temperature, and turns on and off automatically as needed to maintain this temperature.
CLEANING AND CARE The water and air jet systems should be cleaned before first use and on a monthly basis afterwards while the bathtub is in normal use. WATER JET SYSTEM (Jetted Bathtubs Only) 1. Fill the tub with WARM water 2-3 inches above the jets. Add 1/4 to 1/2 box of baking soda to the bathtub water. 2. Turn on jet massage system and run for 10 minutes. 3. Drain tub. 4. Fill tub with COLD water 2-3 inches above jets. 5. Turn on water jet system and run for 10 minutes. 6. Drain tub. 7.
FREQUENTLY ASKED QUESTIONS Q. A. Does the bathtub come with supply hoses? These are not supplied with the tub. Hoses are available at any home supply or hardware store. Q. A. What size threads are the faucet taps? The faucet threads are all 1/2" NIP. Q. A. Q. A. Q. A. Q. A. Q. A. Q. A. Q. A. Q. A. What if I am missing a part? Carefully double-check all packaging and cartons. If you are still missing a part please call 877629-5503 and ask for the Parts Department.
ALLURE WARRANTY POLICY Allure® Bathroom Fixtures carry 5-year warranties. This is a manufacturer’s warranty, which covers the mechanical and electrical assemblies of each bathroom fixture. There is a lifetime warranty on the door seal. Installation and associated labor is the singular responsibility of the owner, not Allure. Any costs related to installation and labor remain the responsibility of the owner and not Allure.
Technical Support: Call toll-free (877) 629-5503