D-Link WMP-G04 2.
Contents Introduction ......................................................................................................3 Wireless Basics ...............................................................................................5 6 Getting Started ................................................................................................. 9 Using the Configuration Utility .................................................................... 12 Networking Basics ...............................
Introduction The Alpha Networks WMP-G04 Wireless Mini PCI Card is an enhanced 802.11g high-performance, wireless adapter that supports high-speed wireless networking at home, at work or in public places. Unlike most network cards, the WMP-G04 provides speeds of up to 54 Mbps (compared to the standard 11 Mbps) This means that you do not need to change your entire network to maintain connectivity. You may sacrifice some of 802.11g’ s speed when you mix 802.11b and 802.
The WMP-G04 is compatible with existing 802.11b devices such as the AirPlus, AirPlusXtremeG and AirPremier family of products including the DWL-520, DWL-520+ and the DWL-AG530 Wireless PCI Adapter, the DI-624 Wireless Router/Access Point and the DWL-120 Wireless USB Adapter. (When used with 802.11b devices, the WMP-G04 will reach speeds at up to 11Mbps.) It is an ideal way to connect one laptop computer to a Wireless Local Area Network (WLAN.
Wireless Basics Alpha wireless products are based on industry standards to provide easy-touse and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the Alpha wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Wireless Basics (continued) People use wireless LAN technology for many different purposes: Mobility - Productivity increases when people have access to data in any location within the operating range of the WLAN. Management decisions based on real-time information can significantly improve worker efficiency. Low Implementation Costs – WLANs (Wireless Local Area Networks) are easy to set up, manage, change and relocate.
Wireless Basics (continued) Standards-Based Technology The WMPL-G04 Wireless Mini PCI Card increases the data rate up to 54 Mbps within the 2.4GHz band, utilizing OFDM technology. This means that in most environments, within the specified range of this device, you will be able to transfer large files quickly or even watch a movie in MPEG format over your network without noticeable delays.
Wireless Basics (continued) Installation Considerations The D-Link WMP-G04 lets you access your network, using a wireless connection, from virtually anywhere. Keep in mind, however, that the number , thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business.
Getting Started There are basically two modes of networking: n Access Point – using an Access Point, such as the DWL-900AP. n Peer-to-Peer – directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more WMP-G04 wireless network Mini PCI card. On the following pages we will show you an example of an Infrastructure Network and an Ad Hoc Network. An Infrastructure network contains an Access Point or Router.
Using the Configuration Utility If you wish to change the default settings or optimize the performance of the WMP-G04, D-Link has included a configuration utility for this purpose. However, in Windows XP, you will instead use zero configuration utility. Before you use the configuration utility for the WMP-G04, you must install the drivers and the configuration utility from the CD-ROM that came with the WMPG04. (Please see the Quick Installation Guide that came with the product.
Configuration Utility Link Info State: Displays the MAC Address of the Access Point that is associated with the WMP-G04. CurrentTxRate: The factory setting is set to 11 Mbps; however,Current TxRate: The default setting is 2. meaning displays the current transmit rate of the current association. Current Channel: Displays the channel information. Shows the channel on which the connection is made . In Access Point mode, this number changes as the radio scans the available channels.
Configuration Utility Configuration This configuration screen displays the default settings for the WMP-G04 To communicate on the network all devices must have the same settings for the following properties: Profiles Name You can manage the profiles that you have created for the wireless network at home, at the office and in public places. Scroll up and down and highlight the profile that you wish to configure. You can add a profile.
Configuration Utility Encryption Encryption – enable Encryption by pulling down the field . Encryption is disabled as the default setting. Create Keys Manually – enter a key in either ASCII (e.g., a word) or hexadecimal format Key Format – ASCII or Hexadecimal Key type – select the key length, either 64, or 128 bits, or 256 bits WEP Key – You can create up to 4 different security keys Click Apply to save the changes.
Configuration Utility IBSS IBSS Channel Selection However, the WMP-G04 will automatically select the channel to match the channel setting for the selected Access Point. In Ad Hoc mode, the channel must be manually set to the same channel for each wireless adapter.
Configuration Utility About The ABOUT screen gives you information about the Firmware and Utility Versions of the WMP-G04.
Networking Basics Using the Network Setup Wizard in Windows XP In this section you will learn how to establish a network at home or work, using Microsoft Windows XP. Note: Please refer to websites such as http://www.homenethelp.com and http://www.microsoft.com/windows2000 for information about networking computers using Windows 2000, ME or 98SE. Go to Start>Control Panel>Network Connections Select Set up a home or small office network When this screen appears, click Next.
Networking Basics Please follow all the instructions in this window: Click Next In the following window, select the best description of your computer. If your computer connects to the internet through a gateway/router, select the second option as shown.
Networking Basics Enter a Computer description and a Computer name (optional.) Click Next Enter a Workgroup name. All computers on your network should have the same Workgroup name.
Networking Basics Please wait while the Network Setup Wizard applies the changes. When the changes are complete, click Next. Please wait while the Network Setup Wizard configures the computer. This may take a few minutes.
Networking Basics In the window below, select the option that fits your needs. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next. Insert a disk into the Floppy Disk Drive, in this case drive A.
Networking Basics Please read the information under Here’ s how in the screen below. After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network. To continue click Next.
Networking Basics Please read the information on this screen, then click Finish to complete the Network Setup Wizard. The new settings will take effect when you restart the computer. Click Yes to restart the computer. You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network. After running the Network Setup Disk on all your computers, your new wireless network will be ready to use.
Networking Basics Naming your Computer To name your computer, please follow these directions:In Windows XP: n Click Start (in the lower left corner of the screen) n n Right-click on My Computer Select Properties and click n Select the Computer Name Tab in the System Properties window. n You may enter a Com- puter Description if you wish; this field is optional. n To rename the computer and join a domain, Click Change.
Networking Basics Naming your Computer n In this window, enter the Computer name n Select Workgroup and enter the name of the Workgroup n All computers on your network must have the same Workgroup name. n Click OK Checking the IP Address in Windows XP The wireless adapter-equipped computers in your network must be in the same IP Address range (see Getting Started in this manual for a definition of IP Address Range.
Networking Basics Checking the IP Address in Windows XP This window will appear. n Click the Support tab n Click Close Assigning a Static IP Address in Windows XP/2000 Note: Residential Gateways/Broadband Routers will automatically assign IP Addresses to the computers on the network, using DHCP (Dynamic Host Configuration Protocol) technology. If you are using a DHCP-capable Gateway/Router you will not need to assign Static IP Addresses.
Networking Basics Assigning a Static IP Address in Windows XP/2000 n Double-click on Network Connections n Right-click on Local Area Connections n Double-click on Properties 28
Networking Basics Assigning a Static IP Address in Windows XP/2000 n Click on Internet Protocol (TCP/IP) n Click Properties n In the window below, select Use the following IP address. Input your IP address and subnet mask. (The IP Addresses on your network must be within the same range. For example, if one computer has an IP Address of 192.168.0.2, the other computers should have IP Addresses that are sequential, like 192.168.0.3 and 192.168.0.4.
Networking Basics Checking the Wireless Connection by Pinging in Windows XP and 2000 n Go to Start > Run > type cmd. A window similar to this one will appear. Type ping xxx.xxx.xxx.xxx, where xxx is the IP Address of the Wireless Router or Access Point. A good wireless connection will show four replies from the Wireless Router or access point, as shown. Checking the Wireless Connection by Pinging in Windows ME and 98SE n Go to Start > Run > type command. A window similar to this will appear.
Warranty and Registration Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“ D-Link” ) provides this Limited warranty for its product only to the person or entity that originally purchased the product from: n D-Link or its authorized reseller or distributor and n Products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, addresses with an APO or FPO.
Governing Law: This Limited Warranty shall be governed by laws of the State of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This Limited warranty provides specific legal rights and the product owner may also have other rights which vary from state to state. Trademarks: D-Link is a registered trademark of D-Link Systems, Inc.
This device is intended only for OEM integrators under the following conditions: (1) The antenna must be installed such that 20cm is maintained between the antenna and users, and (2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing will not be required.
